DOWNLOAD Sony CDP-XA20ES Service Manual ↓ Size: 833.94 KB | Pages: 38 in PDF or view online for FREE

– 9 –

A

2

nylon rivet

3

lug

4

leaf spring
(spindle)

5

two nylon rivets

0

Removal the optical
pick-up to direction
of the arrow 

A

.

6

lug

7

leaf spring (A) (OP)

8

claw

9

sled shaft

1

wire (flat type) (16 core)
(optical pick-up connector)

1

Pull the tray.

3

Hang the belt

4

screw
(BVTP 3 

×

 8)

6

loading motor board

7

Remove the two
solders of loading motor.

5

two claws

8

loading motor
(M103)

2

connector
(CN103)

– 10 –

4

two screws
(BV/RING)

1

three connectors
(CN901, 902, 951)

2

four screws
(BVTT 3 

×

 6)

4

screw (BV/RING)
(AEP, UK)

3

power board

5

two screws
(BVTT 3 

×

 6)

6

Removal the main board
to direction of the arrow 

A

.

A

– 11 –

Connect the TP19 (AFADJ) on the BD board to the ground and
turn on the power supply.
The AF mode is then activated and the following check can be
made.

After confirming display of all on, keep pressing the following
button, and the following display is attained.

” (PLAY) button

 (Display: 01)

P

 

(PAUSE) button

2

4

6

8

10

12

14

16

18

20

 (Display: 02)

(

(

count display

button number
display

A track number on FL display tube increases if 

= AMS +

knob is rotated in 

+ direction, or decreases in = direction.

Keep pressing the

§OPEN/CLOSE button, and all on display is

attained again.

All buttons are assigned with numbers respectively, and when each
button is pressed, it is counted and its number is displayed.  Up to
“16” can be counted.
A button pressed once is not further counted but the number is
displayed. (Table 4-1)

Button

Display

Button

Display

TIME

 

09

PUSH

24

ENTER

PLAY

10

EDIT/

27

MODE

TIME FADE

AUTO

18

REPEAT

28

SPACE

CHECK

19

PEAK

29

SEARCH

CLEAR

20

p

33

FADER

21

(

01

0

22

P

02

)

23

§

all light

OPEN/CLOSE

up

All buttons are assigned with numbers respectively.
If a button is kept pressed, its button number is displayed on the
FL display tube of main unit.  (Table 4-2)

(

button number
display

– 12 –

Button

Display

Button

Display

1

 

00

10

32

2

01

>10

39

3

02

TIME

40

4

03

A – B

42

5

04

REPEAT

44

6

05

=

48

7

06

+

49

8

07

·

50

9

08

0

51

CHECK

13

)

52

CLEAR

15

SHUFFLE

53

+

18

p

56

–

19

P

57

CONTINUE

29

DISPLAY

86

ON/OFF

PROGRAM

31

FADER

95

Button No.

Test Mode

3

Tracking servo off

8

Tracking servo on

11

S-curve measuring mode

12

All servo off

13

Top turnblack display

14

Botton turnblack display

15

Center display

16

Optimum point display

17

Optimum jitter display

18

TE traverse display

19

VC, FE and RF display

20

Autogain display
(Focus, tracking and sled)

* For button numbers 3, 8, 11, and 12, use them only when an

oscilloscope is connected.

The spindle servo can be operated for play in the CLV-S mode by
connecting TP18 (ADJ) and after turning on the power supply.

Disconnect the lead wire of test point connected in first step.

Connect the TP18 (ADJ) on the BD board to the ground and turn
on the power supply.  The ADJ mode is then activated and the
following operation is executed.
• There is no problem even if Guarded Frame Sync is low value

continuously during playing.

• Do not perform high speed search during an access.
• The gain of focus servo and spindle servo does not lower during

playing.

• Manual operation and measurement of the servo system are pos-

sible.  (For detailed operating method, see Table 4-3. in ADJ
Mode.)

After all music numbers are displayed, press the  TIME  button,
and the jitter display mode is then set.  The button functions are as
listed below.

Button Functions (Operate with remote commander.)

Connecting Location:
[BD  BOARD] – Side B –

TP19 (AFADJ)

TP18 (ADJ)

IC102

IC351

IC361