Sony CDP-EX880 / CDP-MS717 / DHC-EX880MD / DHC-MD717 Service Manual ▷ View online
– 37 –
6-7.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC301
µ
PD784215GF-516-3BA (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1, 2
NC
O
Not used (open)
3
LED LAT
O
Serial data latch pulse output to the LED driver (IC602) “L” active
4
DRV CS
O
Chip select signal output to the fluorescent indicator tube driver (IC601) “L” active
5
RE
O
Data read enable signal output to the S-RAM (IC315) “L” active
6
WE
O
Data write enable signal output to the S-RAM (IC315) “L” active
7
DRV RST
O
Reset signal output to the fluorescent indicator tube driver (IC601) and LED driver (IC602)
“L”: reset
“L”: reset
8
NC
O
Not used (open)
9
VDD
—
Power supply terminal (+5V)
10
BD RST
O
Reset signal output to the BD section “L”: reset
11
BD PWR
O
Power on/off control signal output for the BD section power supply “L”: power on
Not used (open)
Not used (open)
12, 13
NC
O
Not used (open)
14
LD OUT
O
Motor control signal output to the loading motor driver (IC371) “L” active *1
15
LD IN
O
Motor control signal output to the loading motor driver (IC371) “L” active *1
16
STK DW
O
Motor control signal output to the elevator up/down motor driver (IC371) “L” active *2
17
STK UP
O
Motor control signal output to the elevator up/down motor driver (IC371) “L” active *2
18
OUT SW
I
Detection input from the disc tray open/close detect switch (SW505)
“L”: disc tray is open, “H”: disc tray is close
“L”: disc tray is open, “H”: disc tray is close
19
IN SW
I
Detection input from the disc tray open/close detect switch (SW505)
“L”: disc tray is close, “H”: disc tray is open
“L”: disc tray is close, “H”: disc tray is open
20
STK SW
I
Detection input from the stocker switch (SW501)
“L”: when sub tray is completely set into the stoker
“L”: when sub tray is completely set into the stoker
21
MID SW
I
Detection input from the mid switch (SW504)
“L”: when sub tray is at the position where it between removed tray and set into the stoker
“L”: when sub tray is at the position where it between removed tray and set into the stoker
22
TEST
I
Input terminal for the test (fixed at “L” in this set)
23
INIT SW
I
Detection input from the init switch (SW502)
“L”: when disc tray is at the position where it can be play
“L”: when disc tray is at the position where it can be play
24
CNT SW
I
Detection input from the count switch (SW503)
“L”: when elevator is at the position where it each sub tray stock position
“L”: when elevator is at the position where it each sub tray stock position
25
PANEL SW
I
Detection input from the CD tray open/close detect switch (S671)
“L”: CD panel close, “H”: CD panel open
“L”: CD panel close, “H”: CD panel open
26
(GND)
I
Not used (fixed at “L”)
27
ADJ
I
Input terminal for the CD test mode setting “L”: test mode, normally: “H”
28
AMUTE
O
Analog line muting on/off control signal output terminal “L”: line muting on
29
DATA
O
Serial data output to the CXD2519Q (IC103) in BD section
30
CLK
O
Serial data transfer clock signal output to the CXD2519Q (IC103) in BD section
31
XLT
O
Serial data latch pulse output to the CXD2519Q (IC103) in BD section “L” active
32
BUSCLK
I
Bus data reading clock signal input for the system control bus
33 to 36
BUSD0 to
BUSD3
I/O
Two-way data bus with the system control bus
37
VDD
—
Power supply terminal (+5V)
38
X2
O
Main system clock output terminal (12.5 MHz)
*1 Loading motor (M502) control
*2 Elevator up/down motor (M501) control
Function
Function
Terminal
Terminal
LD IN (pin !∞)
“L”
“H”
“H”
“L”
STK UP(pin !¶)
“L”
“H”
“H”
“L”
LD OUT (pin !¢)
“H”
“L”
“H”
“L”
STK DW (pin !§)
“H”
“L”
“H”
“L”
IN
OUT
BRAKE
RUN
IDLE
UP
DOWN
BRAKE
RUN
IDLE
– 38 –
Pin No.
Pin Name
I/O
Function
39
X1
I
Main system clock input terminal (12.5 MHz)
40
VSS
—
Ground terminal
41
XT2
O
Sub system clock output terminal Not used (open)
42
XT1
I
Sub system clock input terminal Not used (fixed at “L”)
43
RESET
I
System reset signal input from the reset signal generator (IC311) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
44
BUSCLK
O
Bus data transfer clock signal output for the system control bus
45
BUSBSY
I/O
Busy signal in/out terminal for the system control bus
46
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2519Q (IC103) in BD section
47
DQSY
I
Data read enable signal input from the CD text decoder (IC104) in BD section
48
NC
O
Not used (open)
49
JOG0
I
Jog dial pulse (0) input from the rotary encoder (S661) (for SELECTOR)
50
JOG1
I
Jog dial pulse (1) input from the rotary encoder (S661) (for SELECTOR)
51
AVDD
—
Power supply terminal (+5V) (for A/D converter)
52
AVREF0
I
Reference voltage (+5V) input terminal (for A/D converter)
53
KEY0
I
Key input terminal (A/D input) (S611 to S613, S616 and S618)
CD1 to CD3, REPEAT, CLEAR keys input
CD1 to CD3, REPEAT, CLEAR keys input
54
KEY1
I
Key input terminal (A/D input) (S621 to S623, S626 to S628)
§ (CD1 to CD3), MENU/NO, ENTER/YES, DISC SKIP keys input
§ (CD1 to CD3), MENU/NO, ENTER/YES, DISC SKIP keys input
55
KEY2
I
Key input terminal (A/D input) (S631 to S638)
fl, p, 0, ), DISPLAY, CONTINUE, SHUFFLE, PROGRAM keys input
fl, p, 0, ), DISPLAY, CONTINUE, SHUFFLE, PROGRAM keys input
56
SELECT0
(CDTEXT)
I
Input terminal for the Japanese letter in function setting
“L”: input possible (fixed at “H” in this set)
“L”: input possible (fixed at “H” in this set)
57
SELECT1
(MECHA MODEL)
I
Input terminal for the separate/complete type setting of CD section and other sections
“L”: separate type, “H”: complete type (fixed at “L” in this set)
“L”: separate type, “H”: complete type (fixed at “L” in this set)
58
DISC SNS
I
Detection input from the disc in detect sensor (Q501) “H”: disc in
59
MID SNS
I
Detection input from the disc tray close detect sensor (IC501) “H”: disc tray is closed
60
(GND)
I
Not used (fixed at “L”)
61
AVSS
—
Ground terminal (for A/D converter)
62
TEST
I
Input terminal for the test (fixed at “L” in this set)
63
NC
O
Not used (open)
64
AVREF1
I
Reference voltage (+5V) input terminal (for D/A converter)
65
SRDT
I
Serial data input from the CD text decoder (IC104) in BD section
66
NC
O
Not used (open)
67
SCLK
O
Serial data transfer clock signal output to the CD text decoder (IC104) in BD section
68
SUBQ
I
Subcode Q data input from the CXD2519Q (IC103) in BD section
69
NC
O
Not used (open)
70
SQCLK
O
Subcode Q data reading clock signal output to the CXD2519Q (IC103) in BD section
71
XMODE
O
Reset/power down mode setting signal output to the CD text decoder (IC104) in BD section
72
SENSE2
I
Internal status monitor input from the CXA1992AR (IC101) in BD section
73
SENSE
I
Internal status monitor input from the CXD2519Q (IC103) in BD section
74
DRV DAT
O
Serial data output to the fluorescent indicator tube driver (IC601) and LED driver (IC602)
75
DRV CLK
O
Serial data transfer clock signal output to the fluorescent indicator tube driver (IC601) and LED
driver (IC602)
driver (IC602)
76 to 83
A0 to A7
O
Address signal output to the S-RAM (IC315)
84 to 91
D0 to D7
I/O
Two-way data bus with the S-RAM (IC315)
92 to 98
A8 to A14
O
Address signal output to the S-RAM (IC315)
99
NC
O
Not used (open)
100
VSS
—
Ground terminal
– 39 –
• Waveforms
– BD Board –
– BD Board –
1
IC101
#£
(RF O) (CD PLAY)
Approx.
1.2 Vp-p
2
IC101
$∞
(TEO) (CD PLAY)
Approx.
180 mVp-p
3
IC101
1
(FEO) (CD PLAY)
4
IC103
@¶
(MDP) (CD PLAY)
Approx.
280 mVp-p
2.4 Vp-p
7.6
µ
s
6
IC103
^º
(XPCK)
7
IC103
*ª
(XTAI)
8
IC103
&¢
(WFCK)
5
IC103
^™
(RFCK)
4.9 Vp-p
136
µ
s
5 Vp-p
230 ns
80 mVp-p
16.9344 MHz
5 Vp-p
136
µ
s
– PANEL Board –
1
IC601
@¡
(XIN)
2
IC601
@º
(XOUT)
– MAIN Board –
1
IC103
#ª
(X1)
3 Vp-p
12.5 MHz
750 mVp-p
Approx. 740 kHz
4.7 Vp-p
Approx. 753 kHz
– 40 –
SECTION 7
EXPLODED VIEWS
The components identified by
mark
mark
! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
specified.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list is given in the last of
the electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
(1) MAIN SECTION
1
4-977-699-11 LEG (F)
2
4-988-161-01 SPRING, RING
3
4-995-074-01 KNOB (JOG)
4
X-4949-032-1 PANEL ASSY, FRONT
5
4-962-708-01 EMBLEM (4-A), SONY
6
X-4949-035-1 LID ASSY
* 7
1-667-599-11 LED BOARD
* 8
A-4724-093-A PANEL BOARD, COMPLETE
9
3-363-099-01 SCREW (CASE 3 TP2)
10
4-977-698-11 CASE
* 11
4-995-118-11 PANEL (CD), BACK (EX880)
* 11
4-995-118-21 PANEL (CD), BACK (MS717)
* 12
1-667-598-16 JACK BOARD
* 13
A-4724-092-A MAIN BOARD, COMPLETE
14
4-965-822-01 FOOT
15
4-951-620-41 SCREW (2.6), +BVTP
16
1-783-102-11 WIRE (FLAT TYPE) (5 CORE)
17
1-783-104-11 WIRE (FLAT TYPE) (17 CORE)
18
1-783-105-11 WIRE (FLAT TYPE) (23 CORE)
19
1-783-103-11 WIRE (FLAT TYPE) (11 CORE)
20
4-989-453-01 CUSHION (LID)
7
6
5
4
3
20
2
15
15
15
14
17
18
13
11
12
9
10
19
1
8
15
9
16
#2
#2
#1
#1
#1
#2
CDM48B-5BD29
not supplied
not supplied
#1
Click on the first or last page to see other CDP-EX880 / CDP-MS717 / DHC-EX880MD / DHC-MD717 service manuals if exist.