Sony CDP-CE105 Service Manual ▷ View online
— 5 —
SECTION 2
GENERAL
LOCATION OF CONTROLS
1 POWER switch
2 Front cover
3 OPEN switch
4 Display window
5 CONTINUE button
6 SHUFFLE button
7 PROGRAM button
2 Front cover
3 OPEN switch
4 Display window
5 CONTINUE button
6 SHUFFLE button
7 PROGRAM button
8 REPEAT button
9 DISC SKIP button
0 ) ± (manual search, AMS*) button
9 DISC SKIP button
0 ) ± (manual search, AMS*) button
!¡ ≠ 0 (manual search, AMS*) button
!™ p (STOP) button
!£ · P (play, pause) button
!¢ DISC 1-5 buttons
* AMS is the abbreviation for Automatic Music Sensor.
1
2
3
4
5678
9
0
!¡
!™
!£
!¢
— 6 —
SECTION 3
DISASSEMBLY
Note:
Follow the disassembly procedure in the numerical order given.
3-1. FRONT PANEL BLOCK
1
Remove the case.
2
Flat type wire (19 core)
(Main board, CN302)
(Main board, CN302)
3
Screw (BVTT 3x8)
4
Two screws (BVTT 3x8)
Claw
Claw
3-2. CD MECHANISM DECK
1
Flat type wire (20 core)
(Main board, CN304)
(Main board, CN304)
2
Connector 9P
(Main board, CN303)
(Main board, CN303)
3
Two screws (BVTT3x6)
4
Three screws (BVTT 3x6)
5
CD mechanism deck
— 7 —
3-3. BU BRACKET ASSEMBLY
1
Yoke bracket
2
BU bracket assembly
3-4. DISC TABLE
Note:
When the Disc table is installed, adjust the positions
of Roller cam and mark
of Roller cam and mark
( as shown in the figure, then
set to the groove of disc table.
1
Screw (BVTP 3x8)
2
Screw (BVTP 3x8)
3
Bracket (BU)
4
Step screw
5
Disc table
A
A
— 8 —
SECTION 4
TEST MODE
4-1. AF MODE
The following checks can be performed in the AF mode, which is
set by connecting the test point (AFJ) terminal on DISPLAY
board to the Ground and turning on the power.
set by connecting the test point (AFJ) terminal on DISPLAY
board to the Ground and turning on the power.
• FL tube check
After all segments light up, when the
≠0 button is pressed,
the following will be displayed. (Partial lighting 1)
4-2. ADJ MODE
The following operations are performed in the ADJ mode, which
is set by connecting the test point (ADJ) terminal to the Ground and
turning on the power.
is set by connecting the test point (ADJ) terminal to the Ground and
turning on the power.
• Servo related manual operations and measurement can be
performed.
(For details of operations, refer to Table of Key Operations in ADJ
Mode.)
(For details of operations, refer to Table of Key Operations in ADJ
Mode.)
TABLE OF BUTTON OPERATIONS IN ADJ MODE
The functions of the number buttons are shown in the following
table.
table.
FUNCTIONS OF NUMBER BUTTONS
(Use the widely use remote commander with 20 keys.)
Function
15
16
17
18
19
20
S curve check (in stop mode)
Tracking servo, sled servo off
Tracking servo, sled servo on
E-F balance indication
E-F balance indicati down
E-F balance indication up
Button
[ DISPLAY BOARD ] — Conductor Side —
(Partial lighting 1)
When the
)± button is pressed, the following will be dis-
played. (partial lighting 2)
(Partial lighting 2)
When the
p button is pressed, all will light up again.
• Key check
All buttons have corresponding button numbers. When a button
is pressed, the counter will count up and display the button’s num-
ber. However, the counter will only count to “14”. It will not count
for buttons already pressed once, but will display the button’s num-
ber.
is pressed, the counter will count up and display the button’s num-
ber. However, the counter will only count to “14”. It will not count
for buttons already pressed once, but will display the button’s num-
ber.
Â
Â
Display of button
number
number
Display of counting
DISC 4
DISC 5
CONTINUE
SHUFFLE
PROGRAM
REPEAT
DISC SKIP
07
All lit
Partial lighting 1
Partial lighting 2
08
09
10
Button No.
Displayed
Button No.
Displayed
· P
p
≠ 0
) ±
DISC 1
DISC 2
DISC 3
18
17
13
12
11
19
20
Button
Button
IC401
R404
R405
TP
AFJ
TP
ADJ
Click on the first or last page to see other CDP-CE105 service manuals if exist.