Sony CDP-C591 / CDP-CE235 / CDP-CE335 / SEN-R2900 Service Manual ▷ View online
— 4 —
HOW TO OPEN THE DISC TRAY WHEN POWER
SWITCH TURNS OFF
SWITCH TURNS OFF
NOTE FOR MAIN GEAR INSTALLATION
IN
OUT
Tray
Insert a tapeing driver into the aperture of the unit bottom,
and turn in the direction of arrow (to OUT direction.)
and turn in the direction of arrow (to OUT direction.)
* To close the disc tray, turn the driver
in the reverse direction(to IN direction).
in the reverse direction(to IN direction).
2
Set the cut-out of the ENCODER
to the right when viewed from the front view.
3
Install the MAIN GEAR while aligning
the protrusion of the MAIN GEAR to
the cut-off of the ENCODER.
the cut-off of the ENCODER.
6
Stopper washer (5)
5
Rotate the MAIN GEAR until the portion
that has no gears, of the MAIN GEAR
is aligned with the shaft of the GEAR (REV).
Then insert the GEAR (REV).
is aligned with the shaft of the GEAR (REV).
Then insert the GEAR (REV).
Projected portion
SHAFT
1
Rotate the GEAR (U/D)
to the arrow
A
direction.
4
Open the SET LEVER and
LOCK LEVER in the direction of
the arrow
the arrow
B
, and push in the MAIN GEAR.
Front view
B
B
A
— 5 —
SECTION 1
GENERAL
Identifying the Parts
Front Panel
1
1
/
u
POWER switch
2
CONTINUE button
3
SHUFFLE button
4
PROGRAM button
5
REPEAT button
6
DISC CHECK button
7
DISC 1-5 button
8
Display window
9
”
(play) button
!º
P
(pause) button
!¡
p
(stop) button
!™
EX-CHANGE button
!£
DISC SKIP button
!¢
6
OPEN/CLOSE button
!∞
AMS knob
!§
FADER button
!¶
MUSIC SCAN button
!•
CLEAR button
!ª
CHECK button
@º
)
(forward) button
@¡
0
(backward) button
@™
Disc tray
@£
PEAK SEARCH button
@¢
EDIT/TIME FADE button
@∞
TIME button
1
2 3 4 5 6
7
8
9 0 !¡
!™
!£
!¢
!∞
!§
!•
@º
@™
@£
@¢
@∞
!¶
!ª
@¡
— 6 —
SECTION 2
DISASSEMBLY
2-2. BACK PANEL AND DISC TABLE
Note :
Follow the disassembly procedure in the numerical order given.
2-1. CASE, BOTTOM PLATE AND FRONT PANEL
5
Four screws
(BVTP 3
×
10)
7
Bottom plate
!¡
Three screws
(BVTP 3
×
10)
6
Three screws
(BVTP 3
×
10)
2
Two screws
(M3
×
8)
3
Two screws
(BV3
×
8)
1
Two screws
(M3
×
8)
0
Two screws
(BVTT3
×
8)
!™
Front panel
4
Case
8
Flat type wire(35 core)
(MAIN board, to CN402)
9
Flat type wire(9 core)
(MAIN board, to CN402)
7
Screw
(BVTP 3
×
8)
!¡
Screw
(BVTP 3
×
8)
9
Screw
(BVTP 3
×
8)
5
Screw
(BVTP 3
×
8)
6
Bracket (guide B1)
!™
Bracket
(guide B1)
0
Bracket (guide F1)
8
Bracket (guide F1)
4
Flat type wire(6 core)
(MAIN board, to CN404)
1
Connector
3
Back panel
!¢
Disc table(B)
!∞
Disc table(A)
2
Five screws
(BVTP 3
×
10)
!£
Screw
(PTPWH 3
×
12)
— 7 —
2-3. OPTICAL PICK-UP BLOCK ASSEMBLY
2-4. BRACKET (GEAR) ASSEMBLY
Note :
As for the installation of the main gear, refer to “Note for MAIN
GEAR installation” on page 4.
GEAR installation” on page 4.
5
Two screws
(PTPWH 2.6
×
6)
4
Two screws
(PTPWH 2.6
×
6)
7
Compression spring(BU)
1
Pull out the tray.
(Refer to "HOW TO OPEN THE DISC TRAY WHEN
POWER SWITCH TURNS OFF" on page 4.)
POWER SWITCH TURNS OFF" on page 4.)
6
Holder (BU)
8
Compression spring (BU)
9
Optical pick-up block assembly
2
Flat type wire(16 core)
(BD board, to CN101)
3
Screw
(PTPWH 3
×
12)
6
Rotary encoder
4
Gear (MAIN)
2
Gear (REV)
8
Gear (U/D)
0
Bracket (GEAR)
assembly
3
Stopper washer(5)
1
Stopper washer(5)
7
Stopper washer(5)
5
Screws
(BVTP 3
×
8)
9
Five screws
(BVTP 3
×
8)