Sony BDV-F7 / HBD-F7 Service Manual ▷ View online
HBD-F7
9
NOTE OF CONNECTON OF THE CN601 AND CN602
ON MB-134 BOARD
Both the harness from AMP board and the harness from USB
board can be connected with the CN601 and CN602 on MB-134
board. Refer to “2-13. USB BOARD BLOCK” (page 19) and “2-
14. MB-134 BOARD” (page 20) when you connect the harness
with the CN601 and CN602 on MB-134 board so as not to connect
it by mistake.
ON MB-134 BOARD
Both the harness from AMP board and the harness from USB
board can be connected with the CN601 and CN602 on MB-134
board. Refer to “2-13. USB BOARD BLOCK” (page 19) and “2-
14. MB-134 BOARD” (page 20) when you connect the harness
with the CN601 and CN602 on MB-134 board so as not to connect
it by mistake.
CN601
CN602
Wire to the USB board (CN856)
and MB-134 board (CN601).
and MB-134 board (CN601).
USB board
MB-134 board
MB-134 board
Wire to the AMP board (CN853)
and MB-134 board (CN602).
and MB-134 board (CN602).
AMP board
USB
board
board
to AMP
board
board
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistors referring to the fi gure below.
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistors referring to the fi gure below.
• AMP board (C318, C350, C366)
Both ends of CN301.
CN301
5
C318 C350 C366
– AMP Board (Conductor Side) –
800
:/2 W
1
• POWER board (C903)
Both ends of respective capacitor.
C903
– POWER Board (Conductor Side) –
800
:/2 W
HBD-F7
10
HOW TO EJECT THE DISC WHEN POWER SWITCH TURN OFF
Note 1: After the rear cover is removed, this work is done.
Note 2: Please prepare the JIG Connector (Part No. 1-770-638-11 FFC connector/FPC 7P).
Note 3: Operate by setting up the BD drive without fail in the vertical direction.
Note 2: Please prepare the JIG Connector (Part No. 1-770-638-11 FFC connector/FPC 7P).
Note 3: Operate by setting up the BD drive without fail in the vertical direction.
REGULATED
DC POWER
SUPPLY
DC POWER
SUPPLY
2 pin
1 pin
Connect JIG connector to wire (flat type) (5 core)
that removes CN2490 of MB-134 board.
that removes CN2490 of MB-134 board.
Refer to below figure and supply DC5V to 1 pin and 2 pin.
JIG connector
CN2490
Note 4: 3 – 7 pin are cut beforehand before it installs connector.
PROCESSING OF LEAD WIRE
AMP board
–
Rear view
–
(Parts are removed until AMP board is seen)
HBD-F7
11
AMP BOARD SERVICE POSITION
• Please connect following extension jig.
• Please connect following extension jig.
Jig No.
Part No.
Pitch (mm)
Cores
Length (mm)
1
J-2501-225-A
1
9
300
2
J-2501-248-A
1
27
300
Connect extension jig
2
to the AMP board (CN103)
and MB-134 board (CN1505).
and MB-134 board (CN1505).
CN1505
MB-134 board
Connect extension jig
1
to the AMP board (CN102)
and FL board (CN701).
and FL board (CN701).
CN701
CN103
CN102
FL board
AMP board
In checking the board, make discharge for
eOectric shock SreYention. (5 00 ȍ2 :)
eOectric shock SreYention. (5 00 ȍ2 :)
Caution
MB-134 BOARD SERVICE POSITION
• Please connect following extension jig.
• Please connect following extension jig.
Jig No.
Part No.
Pitch (mm)
Cores
Length (mm)
3
J-2501-248-A
1
27
300
4
J-2501-086-A
1
19
300
Connect extension jig
3
to the AMP board (CN103) and
MB-134 board (CN1505).
MB-134 board (CN1505).
MB-134 board
Connect extension jig
4
to the AMP board (CN106) and AUDIO board (CN604).
AUDIO board
CN604
CN106
CN103
CN1505
AMP board
HBD-F7
12
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. REAR COVER BLOCK
(Page
(Page
13)
2-3. BOTTOM
(COM)
ASSY
(Page
13)
2-4. FRONT PANEL BLOCK
(Page
(Page
14)
2-6. SHIELD PLATE (REAR) BLOCK
(Page
(Page
15)
2-7. SHIELD PLATE (FRONT) BLOCK,
FUSE
FUSE
(F901)
(Page
16)
2-8. AMP
BOARD
(Page
16)
2-13. USB BOARD
BLOCK
(Page
BLOCK
(Page
19)
2-10. TUNER BLOCK
(Page
(Page
18)
2-9. POWER
BOARD
(Page
17)
2-15. BD DRIVE BLOCK (BSX-1)
(Page
(Page
20)
2-16. BOTTOM COVER
(Page
(Page
21)
2-17. OPTICAL DEVICE
(KEM-460AAA)
(Page
(KEM-460AAA)
(Page
22)
2-14. MB-134 BOARD
(Page
(Page
20)
2-12. SHIELD PLATE
(AUDIO)
(AUDIO)
BLOCK
(Page
19)
2-11. AUDIO BOARD
(Page
(Page
18)
2-5. HAMON (COM) BLOCK
(Page
(Page
15)
2-18. HOW TO BEND FFC
(Page 22, 23)
Click on the first or last page to see other BDV-F7 / HBD-F7 service manuals if exist.