DOWNLOAD Sony BDV-F500 / BDV-F700 / HBD-F500 / HBD-F700 Service Manual ↓ Size: 6.99 MB | Pages: 119 in PDF or view online for FREE

2011C05-1

© 

2011.03

Model Name Using Similar Mechanism

NEW

Mechanism Type

BSX-1

Optical Pick-up Name

KEM-460AAA

•  HBD-F500 is the amplifi er, video, BD/DVD/Super Audio CD/CD system, USB, LAN and tuner section in BDV-F500.
•  HBD-F700 is the amplifi er, video, BD/DVD/Super Audio CD/CD system, USB, LAN and tuner section in BDV-F700.

HBD-F700:
POWER OUTPUT (rated)
Front L/Front R:

85 W + 85 W (at 4 ohms, 1 
kHz, 1% THD)

POWER OUTPUT (reference) 
Front L/Front R:

130 W (per channel at 4 
ohms, 1 kHz)

Subwoofer:

140 W (at 4 ohms, 100 Hz)

HBD-F500:
POWER OUTPUT (rated)
Front L/Front R:

80 W + 80 W (at 4 ohms, 1 
kHz, 1% THD)

POWER OUTPUT (reference) 
Front L/Front R:

115 W (per channel at 4 
ohms, 1 kHz)

Subwoofer:

120 W (at 4 ohms, 100 Hz)

Inputs (Analog)
AUDIO (IN)

Sensitivity: 450/250 mV

Inputs (Digital)
SAT/CABLE (DIGITAL IN OPTICAL), 
TV (DIGITAL IN OPTICAL)

Supported formats: LPCM 
2CH (up to 48 kHz), Dolby 
Digital, DTS

Outputs

VIDEO OUT: 1 Vp-p 75 
ohms
HDMI OUT: Type A (19 
pin)

Signal format system

PAL/NTSC

 (USB) port:

Type A (For connecting 
USB memory, memory 
card reader, digital still 
camera, and digital video 
camera)

Maximum current:

500 mA

LAN (100) terminal

100BASE-TX Terminal

System

PLL quartz-locked digital 
synthesizer

FM tuner section
Tuning range

87.5 MHz - 108.0 MHz 
(50 kHz step)

Antenna (aerial)

FM wire antenna (aerial)

Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency

10.7 MHz

Power requirements
European models:

220 V - 240 V AC, 
50/60 Hz

Latin American models:

110 V - 240 V AC, 
50/60 Hz 

Power consumption
European models:

On: 85 W
Standby: 0.3 W (at the 
Power Saving mode) 

Latin American models:

On: 90 W
Standby: 0.3 W (at the 
Power Saving mode) 

Dimensions (approx.)

452 mm × 198 mm × 119 
mm (w/h/d) incl. 
projecting parts

Mass (approx.)

5.0 kg

Design and specifications are subject to change 
without notice.

Photo: HBD-F500

NOTES  ON  CHIP  COMPONENT  REPLACEMENT
• 

Never reuse a disconnected chip component.

• 

Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

FLEXIBLE  CIRCUIT  BOARD  REPAIRING
• 

Keep the temperature of soldering iron around 270 °C during 
repairing.

• 

Do not touch the soldering iron on the same conductor of the 
circuit board (within 3 times).

• 

Be careful not to apply force on the conductor when soldering 
or unsoldering.

0  OR  DOTTED  LINE  

0  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  

This appliance is classified as a 
CLASS 3R LASER product. 
Visible and invisible laser radiation 
is emitted when the laser protective 
housing is opened, so be sure to 
avoid direct eye exposure.

This marking is located on the laser 
protective housing inside the 
enclosure.

• This system incorporates High-

Definition Multimedia Interface 
(HDMI

TM

) technology.

HDMI, the HDMI logo and High-
Definition Multimedia Interface 
are trademarks or registered 
trademarks of HDMI Licensing 
LLC.

• Java and all Java-based 

trademarks and logos are 
trademarks or registered 
trademarks of Sun Microsystems, 
Inc.

• “BD-LIVE” and 

“BONUSVIEW” are trademarks 
of Blu-ray Disc Association.

• “Blu-ray Disc” is a trademark.

• “Blu-ray Disc,” “DVD+RW,” 

“DVD-RW,” “DVD+R,” “DVD-
R,” “DVD VIDEO,” and “CD” 
logos are trademarks.

• “BRAVIA” is a trademark of 

Sony Corporation.

• “AVCHD” and the “AVCHD” 

logo are trademarks of Matsushita 
Electric Industrial Co., Ltd. and 
Sony Corporation.

•

, “XMB,” and “xross media 

bar” are trademarks of Sony 
Corporation and Sony Computer 
Entertainment Inc.

• “PLAYSTATION” is a trademark 

of Sony Computer Entertainment 
Inc.

• This product incorporates 

copyright protection technology 
that is protected by U.S. patents 
and other intellectual property 
rights.
Use of this copyright protection 
technology must be authorized by 
Macrovision, and is intended for 
home and other limited viewing 
uses only unless otherwise 
authorized by Macrovision.
Reverse engineering or 
disassembly is prohibited.

• This system incorporates with 

Dolby* Digital and the DTS** 
Digital Surround System.

* Manufactured under license 

from Dolby Laboratories.
Dolby and the double-D 
symbol are trademarks of 
Dolby Laboratories.

** Manufactured under license 

under U.S. Patent #’s: 
5,451,942; 5,956,674; 
5,974,380; 5,978,762; 
6,226,616; 6,487,535; 
7,212,872; 7,333,929; 
7,392,195; 7,272,567 & 
other U.S. and worldwide 
patents issued & pending. 
DTS and the Symbol are 
registered trademarks, & 
DTS-HD, DTS-HD Master 
Audio, and the DTS logos 
are trademarks of DTS, Inc. 
Product includes software. 
© DTS, Inc. All Rights 
Reserved.

• DivX

®

, DivX Certified

®

 and 

associated logos are registered 
trademarks of DivX, Inc. and are 
used under license.

• Music and video recognition 

technology and related data are 
provided by Gracenote

®

. 

Gracenote is the industry standard 
in music recognition technology 
and related content delivery. For 
more information, please visit 
www.gracenote.com. 
CD, DVD, Blu-ray Disc, and 
music and video-related data from 
Gracenote, Inc., copyright © 
2000-present Gracenote. 
Gracenote Software, copyright © 
2000-present Gracenote. One or 
more patents owned by Gracenote 
apply to this product and service. 
See the Gracenote website for a 
nonexhaustive list of applicable 
Gracenote patents. Gracenote, 
CDDB, MusicID, MediaVOCS, 
the Gracenote logo and logotype, 
and the “Powered by Gracenote” 
logo are either registered 
trademarks or trademarks of 
Gracenote in the United States 
and/or other countries.

CAUTION
Use of controls or adjustments or performance of procedures 
other than those specifi ed herein may result in hazardous radia-
tion exposure.

  .............................................   4

 

2-1.  Disassembly  Flow ...........................................................   12
2-2.  Rear Cover Block ............................................................   13
2-3.  Bottom  (COM) Assy .......................................................   13
2-4.  Front Panel Block ...........................................................   14
2-5.  Hamon (COM) Block .....................................................   15
2-6.  Shield Plate (Rear) Block ...............................................   16
2-7.  AMP Board .....................................................................   16
2-8.  Tuner Block.....................................................................   17
2-9.  AUDIO  Board .................................................................   17
2-10.  Shield Plate (Audio) Block .............................................   18
2-11.  USB Board Block ...........................................................   18
2-12.  MB-134 Board ................................................................   19
2-13.  Shield Plate (Front) Block, Fuse (F901) .........................   19
2-14.  POWER  Board ................................................................   20
2-15.  BD Drive Block (BSX-1) ...............................................   21
2-16.  Bottom  Cover ..................................................................   22
2-17.  Optical Device (KEM-460AAA) ....................................   23
2-18.  How To Bend FFC ..........................................................   23

TEST  MODE 

 ............................................................   25

ELECTRICAL  CHECK 

 .........................................   34

5-1.  Block Diagram - SERVO Section - ................................   35
5-2.  Block Diagram - MEMORY Section - ............................   36
5-3.  Block Diagram - AUDIO Section - .................................   37
5-4.  Block Diagram - AMP Section - .....................................   38
5-5.  Block Diagram - REGULATOR Section - ......................   39
5-6.  Block Diagram 

- PANEL, POWER SUPPLY Section - ...........................   40

5-7.  Printed Wiring Board 

- MB-134 Board (Component Side) - .............................   42

5-8.  Printed Wiring Board 

- MB-134 Board (Conductor Side) - ...............................   43

5-9.  Schematic Diagram - MB-134 Board (1/13) - ................   44
5-10.  Schematic Diagram - MB-134 Board (2/13) - ................   45
5-11.  Schematic Diagram - MB-134 Board (3/13) - ................   46

5-12.  Schematic Diagram - MB-134 Board (4/13) - ................   47
5-13.  Schematic Diagram - MB-134 Board (5/13) - ................   48
5-14.  Schematic Diagram - MB-134 Board (6/13) - ................   49
5-15.  Schematic Diagram - MB-134 Board (7/13) - ................   50
5-16.  Schematic Diagram - MB-134 Board (8/13) - ................   51
5-17.  Schematic Diagram - MB-134 Board (9/13) - ................   52
5-18.  Schematic Diagram - MB-134 Board (10/13) - ..............   53
5-19.  Schematic Diagram - MB-134 Board (11/13) - ..............   54
5-20.  Schematic Diagram - MB-134 Board (12/13) - ..............   55
5-21.  Schematic Diagram - MB-134 Board (13/13) - ..............   56
5-22.  Printed Wiring Board - AUDIO Board - .........................   57
5-23.  Schematic Diagram - AUDIO Board (1/2) - ...................   58
5-24.  Schematic Diagram - AUDIO Board (2/2) - ...................   59
5-25.  Printed Wiring Boards - AMP Section (1/2) - .................   60
5-26.  Printed Wiring Board - AMP Section (2/2) - ..................   61
5-27.  Schematic Diagram - AMP Section (1/4) - .....................   62
5-28.  Schematic Diagram - AMP Section (2/4) - .....................   63
5-29.  Schematic Diagram - AMP Section (3/4) - .....................   64
5-30.  Schematic Diagram - AMP Section (4/4) - .....................   65
5-31.  Printed Wiring Board - FL Board - .................................   66
5-32.  Schematic Diagram - FL Board - ....................................   67
5-33.  Printed Wiring Boards - PANEL Section - .....................   68
5-34.  Schematic Diagram - PANEL Section - ..........................   69
5-35.  Printed Wiring Board - POWER Board - ........................   70
5-36.  Schematic Diagram - POWER Board - ..........................   71

6-1.  Rear Cover Section .........................................................   97
6-2.  Front Panel Section .........................................................   98
6-3.  AMP Board Section ........................................................   99
6-4.  MB-134 Board Section ...................................................  100
6-5.  Front Shield Section ........................................................  101
6-6.  POWER Board Section ...................................................  102
6-7.  BD Drive Section (BSX-1) .............................................  103

   ..............................  104

Accessories are given in the last of the electrical parts list.

The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by 
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also 
use the procedure in the printed matter which is included in the 
repair parts.
The fl exible board is easily damaged and should be handled with 
care.

NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused 
on the disc refl ective surface by the objective lens in the optical 
pickup block. Therefore, when checking the laser diode emission, 
observe from more than 30 cm away from the objective lens.

UNLEADED  SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with 

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.
•  Unleaded solder melts at a temperature about 40 °C higher 

than ordinary solder.

 

Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.

 

Soldering irons using a temperature regulator should be set to 
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if 

the heated tip is applied for too long, so be careful!

•  Strong viscosity
 

Unleaded solder is more viscous (sticky, less prone to fl ow) 
than ordinary solder so use caution not to let solder bridges 
occur such as on IC pins, etc.

•  Usable with ordinary solder
 

It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.

J-6090-199-A

BLX-104

Single Layer

J-6090-200-A

BLX-204

Dual Layer

J-2501-307-A

CD (HLX-A1)

J-2501-305-A

HLX-513

Single Layer (NTSC)

J-2501-306-A

HLX-514

Dual Layer (NTSC)

J-6090-077-A

HLX-506

Single Layer (PAL)

J-6090-078-A

HLX-507

Dual Layer (PAL)

Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-

989-1

[]) (page 1-3 to 1-14E) for the use of BLX-104/204.

1. BLX-104
Procedure:
1.  Select 23.976Hz/1080p.
2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
4.  Check each outputs.
 Video:
 

Composite/S Video/component/HDMI.

 Audio:
 

Speaker out.

*  When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) 

can use instead of 1080/24p.

 

However this is temporary correspondence.

2. BLX-204
Procedure:
1.  Select 1080i (59.94Hz or 50Hz).
2.  Play “4.Motion picture”.
3.  Check whether player can play back or not (Check the picture 

and sound output).

3.  CD (HLX-A1)
Procedure:
Check whether player can play back or not (Check the sound out-
put).

4.  HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1.  After displayed Main Menu, select “1.Video Signal”.
2.  Play “1.Color bar 100%” (Check the picture and sound out-

put).

3.  Return to Menu.
4.  Play “Demonstration 4:3” or “Demonstration 16:9” (Check the 

picture and sound output).

NOTE  THE  IC101,  IC104,  IC105,  IC204,  IC205,  IC307,  
IC311,  IC501  AND  IC502  ON  THE  MB-134  BOARD  
REPLACING
IC101, IC104, IC105, IC204, IC205, IC307, IC311, IC501 and  
IC502 on the MB-134 board cannot exchange with single. When 
these parts are damaged, exchange the entire mounted board.

RELEASING  THE  DISC  SLOT  LOCK
The disc slot lock function for the antitheft of an demonstration 
disc in the store is equipped.

Releasing Procedure:
1.  Press the [

?/1

] button to turn on the system.

2.  Press the [FUNCTION] button to select “BD/DVD”.
3.  Press the [

x

] and [

Z

] buttons simultaneously and hold for 

more than fi ve seconds, “DEMO OFF” is displayed on the 
fluorescent indicator tube (around 5 seconds).

Note: When “DEMO ON” is displayed, the disc slot lock is not released 

by turning power on/off with the [

?/1] button.

ABOUT  THE  LENS  CLEANING
Do not do the lens cleaning with the cotton bud etc. It causes the 
trouble.