DOWNLOAD Sony BDV-E370 / BDV-E470 / BDV-E570 / BDV-E870 / BDV-T57 / HBD-E370 / HBD-E470 / HBD-E570 / HBD-E870 / HBD-T57 Service Manual ↓ Size: 8.76 MB | Pages: 127 in PDF or view online for FREE

2011A05-1

© 

2011.01

•  HBD-E370 is the amplifi er, video, BD/DVD/Super Audio CD/CD 

system, USB, LAN and tuner section in BDV-E370.

•  HBD-E470 is the amplifi er, video, BD/DVD/Super Audio CD/CD 

system, USB, LAN and tuner section in BDV-E470.

•  HBD-E570 is the amplifi er, video, BD/DVD/Super Audio CD/CD 

system, USB, LAN and tuner section in BDV-E570.

•  HBD-E870 is the amplifi er, video, BD/DVD/Super Audio CD/CD 

system, USB, LAN and tuner section in BDV-E870.

•  HBD-T57 is the amplifi er, video, BD/DVD/Super Audio CD/CD 

system, USB, LAN and tuner section in BDV-T57.

Model Name Using Similar Mechanism

BDP-S370

Mechanism Type

BPX-5

Optical Pick-up Block Name

KEM-460AAA

Photo: HBD-E370

U.S. models:
POWER OUTPUT AND TOTAL HARMONIC 
DISTORTION:
(FTC) 
Front L + Front R:

With 3 ohms loads, both 
channels driven, from 180 

- 20,000 Hz; rated 60 watts 

per channel minimum 
RMS power, with no more 
than 1% total harmonic 
distortion from 250 milli 
watts to rated output.

Other models:
POWER OUTPUT (rated)
Front L/Front R:

108 W + 108 W (at 3 ohms, 
1 kHz, 1% THD)

HBD-E370:
POWER OUTPUT (reference) 
Front L/Front R/Center/Surround L/Surround R:

142 W (per channel at 3 
ohms, 1 kHz)

Subwoofer:

140 W (at 3 ohms, 80 Hz)

HBD-E870/HBD-E570/HBD-E470/HBD-T57:
POWER OUTPUT (reference) 
Front L/Front R/Center/Surround L/Surround R:

167 W (per channel at 3 
ohms, 1 kHz)

Subwoofer:

165 W (at 3 ohms, 80 Hz)

Inputs (Analog)
AUDIO (AUDIO IN)

Sensitivity: 450/250 mV

Inputs (Digital)
SAT/CABLE (COAXIAL), TV (OPTICAL)

Supported formats: LPCM 
2CH (up to 48 kHz), Dolby 
Digital, DTS

Outputs

VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms

P

B

/C

B

, P

R

/C

R

: 0.7 Vp-p 

75 ohms

HDMI OUT: Type A (19 
pin)

Signal format system

NTSC (US, Canadian, PX,

 (USB) port:

Type A (For connecting 
USB memory, memory 
card reader, digital still 

camera, and digital video 
camera)

Maximum current:

500 mA

LAN (100) terminal

100BASE-TX Terminal

System

PLL quartz-locked digital 
synthesizer

FM tuner section
Tuning range
North American and PX models:

(100 kHz step)

Other models:

87.5 MHz - 108.0 MHz 
(50 kHz step)

Antenna (aerial)

FM wire antenna (aerial)

Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency

10.7 MHz

Power requirements
North American and Mexican models:

120 V AC, 60 Hz

Other models: 

50/60 Hz 

Power consumption

On: 170 W
Standby: 0.3 W (at the 
Power Saving mode) 

Dimensions (approx.)

430 mm × 85 mm × 335 
mm (17 in × 3 

3

/

8

 in × 

13 

1

/

4

 in) (w/h/d) incl. 

projecting parts

Mass (approx.)

4.8 kg (10 lb 10 oz)

Design and specifications are subject to change 
without notice.

Latin American and  

PAL/NTSC (Other  
models)

220 - 240 V AC,

Mexican models) 

120 V AC, 50/60 Hz

Taiwan model:

Latin American and PX models: 

110 - 240 V AC,

50/60 Hz 

87.5 MHz - 108.0 MHz 

NOTES  ON  CHIP  COMPONENT  REPLACEMENT
• 

Never reuse a disconnected chip component.

• 

Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

FLEXIBLE  CIRCUIT  BOARD  REPAIRING
• 

Keep the temperature of soldering iron around 270 °C during 
repairing.

• 

Do not touch the soldering iron on the same conductor of the 
circuit board (within 3 times).

• 

Be careful not to apply force on the conductor when soldering 
or unsoldering.

SAFETY  CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, 
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.

LEAKAGE  TEST
The AC leakage from any exposed metal part to earth ground and 
from all exposed metal parts to any exposed metal part having a 
return to chassis, must not exceed 0.5 mA (500 microamperes.). 
Leakage current can be measured by any one of three methods.
1.  A commercial leakage tester, such as the Simpson 229 or RCA 

WT-540A. Follow the manufacturers’ instructions to use these 
instruments.

2.  A battery-operated AC milliammeter. The Data Precision 245 

digital multimeter is suitable for this job.

3.  Measuring the voltage drop across a resistor by means of a 

VOM or battery-operated AC voltmeter. The “limit” indication 
is 0.75 V, so analog meters must have an accurate low-voltage 
scale. The Simpson 250 and Sanwa SH-63Trd are examples 
of a passive VOM that is suitable. Nearly all battery operated 
digital multimeters that have a 2 V AC range are suitable. (See 
Fig. A)

0  OR  DOTTED  LINE  

0  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  

0  SUR  

•  This product incorporates copyright protection technology that is protected by 

U.S. patents and other intellectual property rights.

 

Use of this copyright protection technology must be authorized by Macrovision, 
and is intended for home and other limited viewing uses only unless otherwise 
authorized by Macrovision.

 

Reverse engineering or disassembly is prohibited.

•  This system incorporates with Dolby* Digital and Dolby Pro Logic (II) adaptive 

matrix surround decoder and the DTS** Digital Surround System.
  *  Manufactured under license from Dolby Laboratories.
    Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Labora-

tories.

  ** Manufactured under license under U.S. Patent #’s: 
    5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 

7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide 
patents issued & pending. DTS is a registered trademark and the DTS logos, 
Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc. 

    © 1996-2008 DTS, Inc. All Rights Reserved.

•  This system incorporates High-Defi nition Multimedia Interface (HDMI™) tech-

nology.

 

HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks 
or registered trademarks of HDMI Licensing LLC.

•  Java and all Java-based trademarks and logos are trademarks or registered trade-

marks of Sun Microsystems, Inc.

•  “BD-LIVE” and “BONUSVIEW” are trademarks of Blu-ray Disc Association.
•  “Blu-ray Disc” is a trademark.
•  “Blu-ray Disc,” “DVD+RW,” “DVD-RW,” “DVD+R,” “DVD-R,” “DVD 

VIDEO,” and “CD” logos are trademarks.

•  “BRAVIA” is a trademark of Sony Corporation.
•  “AVCHD” and the “AVCHD” logo are trademarks of Matsushita Electric Indus-

trial Co., Ltd. and Sony Corporation.

•  “S-AIR” and its logo are trademarks of Sony Corporation.
• 

, “XMB,” and “xross media bar” are trademarks of Sony Corporation and Sony 

Computer Entertainment Inc.

•  “PLAYSTATION” is a trademark of Sony Computer Entertainment Inc.
• DivX

®

, DivX Certifi ed

®

 and associated logos are registered trademarks of DivX, 

Inc. and are used under license. (Except for U.S. models.)

•  Music and video recognition technology and related data are provided by Grace-

note

®

. 

 

Gracenote is the industry standard in music recognition technology and related 
content delivery. For more information, please visit www.gracenote.com. 

 

CD, DVD, Blu-ray Disc, and music and video-related data from Gracenote, Inc., 
copyright © 2000-present Gracenote. 

 

Gracenote Software, copyright © 2000-present Gracenote. One or more patents 
owned by Gracenote apply to this product and service. See the Gracenote website 
for a nonexhaustive list of applicable Gracenote patents. Gracenote, CDDB, 
MusicID, MediaVOCS, the Gracenote logo and logotype, and the “Powered by 
Gracenote” logo are either registered trademarks or trademarks of Gracenote in 
the United States and/or other countries.

This appliance is classified as a 
CLASS 1 LASER product. This 
marking is located on the rear 
exterior.

CAUTION
Use of controls or adjustments or performance of procedures 
other than those specifi ed herein may result in hazardous radia-
tion exposure.

  .............................................   4

2-1.   Disassembly Flow ...........................................................   12
2-2.   Case (EZ) ........................................................................   12
2-3.   MB-134 Board ................................................................   13
2-4.   Bracket (MB) Block ........................................................   14
2-5.   Fuse (F901), POWER Board ..........................................   14
2-6.   Front Panel Block ...........................................................   15
2-7.   CONNECT Board ...........................................................   15
2-8.   BD Drive (BPX-5) ..........................................................   16
2-9.   Back Panel Block ............................................................   16
2-10.  MAIN Board ...................................................................   17
2-11.  AUDIO Board .................................................................   17
2-12.  Optical Pick-up Block (KEM-460AAA), 
 

Wire  (Flat  Type) ..............................................................   18

TEST  MODE 

 ............................................................   19

ELECTRICAL  CHECK 

 .........................................   27

5-1.  Block Diagram - SERVO Section - ................................   28
5-2.  Block Diagram - MEMORY Section - ............................   29
5-3.  Block Diagram - TUNER, S-AIR Section - ....................   30
5-4.  Block Diagram - AUDIO Section - .................................   31
5-5.  Block Diagram - REGULATOR Section - ......................   32
5-6.  Block Diagram 
 

- PANEL, POWER SUPPLY Section - ...........................   33

5-7.  Schematic Diagram - MB-134 Board (1/13) - ................   35
5-8.  Schematic Diagram - MB-134 Board (2/13) - ................   36
5-9.  Schematic Diagram - MB-134 Board (3/13) - ................   37
5-10.  Schematic Diagram - MB-134 Board (4/13) - ................   38
5-11.  Schematic Diagram - MB-134 Board (5/13) - ................   39
5-12.  Schematic Diagram - MB-134 Board (6/13) - ................   40
5-13.  Schematic Diagram - MB-134 Board (7/13) - ................   41
5-14.  Schematic Diagram - MB-134 Board (8/13) - ................   42
5-15.  Schematic Diagram - MB-134 Board (9/13) - ................   43
5-16.  Schematic Diagram - MB-134 Board (10/13) - ..............   44

5-17.  Schematic Diagram - MB-134 Board (11/13) - ..............   45
5-18.  Schematic Diagram - MB-134 Board (12/13) - ..............   46
5-19.  Schematic Diagram - MB-134 Board (13/13) - ..............   47
5-20.  Printed Wiring Board 
 

- MB-134 Board (Component Side) - .............................   48

5-21.  Printed Wiring Board 
 

- MB-134 Board (Conductor Side) - ...............................   49

5-22.  Printed Wiring Board - AUDIO Board - .........................   50
5-23.  Schematic Diagram - AUDIO Board - ............................   51
5-24.  Printed Wiring Board 
 

- MAIN Board (Component Side) - ................................   52

5-25.  Printed Wiring Board 
 

- MAIN Board (Conductor Side) - ..................................   53

5-26.  Schematic Diagram - MAIN Board (1/5) - .....................   54
5-27.  Schematic Diagram - MAIN Board (2/5) - .....................   55
5-28.  Schematic Diagram - MAIN Board (3/5) - .....................   56
5-29.  Schematic Diagram - MAIN Board (4/5) - .....................   57
5-30.  Schematic Diagram - MAIN Board (5/5) - .....................   58
5-31.  Printed Wiring Board - CONNECT Board - ...................   59
5-32.  Schematic Diagram - CONNECT Board - ......................   59
5-33.  Printed Wiring Board - REG Board - ..............................   60
5-34.  Schematic Diagram - REG Board - ................................   61
5-35.  Printed Wiring Board - FL Board - .................................   62
5-36.  Schematic Diagram - FL Board - ....................................   63
5-37.  Printed Wiring Board - POWER Board - ........................   64
5-38.  Schematic Diagram - POWER Board - ..........................   65
5-39.  Printed Wiring Boards - KEY Section - ..........................   66
5-40.  Schematic Diagram - KEY Section - ..............................   66

6-1.  Case, Front Panel Section ...............................................   91
6-2.  MB-134 Board Section ...................................................   92
6-3.  Back Panel Section .........................................................   93
6-4.  MAIN Board Section ......................................................   94
6-5.  BD Drive Section (BPX-5) .............................................   95

   ..............................   96

Accessories are given in the last of the electrical parts list.

The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by 
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also 
use the procedure in the printed matter which is included in the 
repair parts.
The fl exible board is easily damaged and should be handled with 
care.

NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused 
on the disc refl ective surface by the objective lens in the optical 
pickup block. Therefore, when checking the laser diode emission, 
observe from more than 30 cm away from the objective lens.

UNLEADED  SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with 

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.
•  Unleaded solder melts at a temperature about 40 °C higher 

than ordinary solder.

 

Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.

 

Soldering irons using a temperature regulator should be set to 
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if 

the heated tip is applied for too long, so be careful!

• 

Strong viscosity

 

Unleaded solder is more viscous (sticky, less prone to fl ow) 
than ordinary solder so use caution not to let solder bridges 
occur such as on IC pins, etc.

• 

Usable with ordinary solder

 

It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.

J-6090-199-A

BLX-104

Single Layer

J-6090-200-A

BLX-204

Dual Layer

J-2501-307-A

CD (HLX-A1)

J-2501-305-A

HLX-513

Single Layer (NTSC)

J-2501-306-A

HLX-514

Dual Layer (NTSC)

J-6090-077-A

HLX-506

Single Layer (PAL)

J-6090-078-A

HLX-507

Dual Layer (PAL)

Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-

989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.

1. BLX-104
Procedure:
1.  Select 23.976Hz/1080p.
2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
4.  Check each outputs.
 Video:
 

Composite/S Video/component/HDMI.

 Audio:
 

Speaker out.

*  When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) 

can use instead of 1080/24p.

 

However this is temporary correspondence.

2. BLX-204
Procedure:
1.  Select 1080i (59.94Hz or 50Hz).
2.  Play “4.Motion picture”.
3.  Check whether player can play back or not (Check the picture 

and sound output).

3.  CD (HLX-A1)
Procedure:
Check whether player can play back or not (Check the sound out-
put).

4.  HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1.  After displayed Main Menu, select “1.Video Signal”.
2.  Play “1.Color bar 100%” (Check the picture and sound out-

put).

3.  Return to Menu.
4.  Play “Demonstration 4:3” or “Demonstration 16:9” (Check the 

picture and sound output).

NOTE  THE  IC101,  IC104,  IC105,  IC204,  IC205,  IC307,  
IC311,  IC501  AND  IC502  ON  THE  MB-134  BOARD  
REPLACING
IC101, IC104, IC105, IC204, IC205, IC307, IC311, IC501 and  
IC502 on the MB-134 board cannot exchange with single. When 
these parts are damaged, exchange the entire mounted board.

RELEASING  THE  DISC  TRAY  LOCK
The disc tray lock function for the antitheft of an demonstration 
disc in the store is equipped.

Releasing Procedure:
1.  Press the [

?/1

] button to turn on the system.

2.  Press the [FUNCTION] button to select “BD/DVD”.
3.  Press the [

x

] and [

Z

] buttons simultaneously and hold down 

unit “DEMO OFF” displayed on the fluorescent indicator tube 
(around 5 seconds).

Note: When “DEMO ON” is displayed, the disc tray lock is not released 

by turning power on/off with the [?/1] button.

ABOUT  THE  LENS  CLEANING
Do not do the lens cleaning with the cotton bud etc. It causes the 
trouble.