Sony AIR-SW10TI / SA-WA10R Service Manual ▷ View online
SA-WA10R
5
2-3. CHASSIS (NET) ASSY
2-4. REAR PANEL BLOCK
2 Raise the chassis (net)
assy a little by little.
five bosses
1 Insert the jig (Part No. J-2501-238-A) into a space and
raise the chassis (net) assy gradually.
Note: When using a jig, please work so as not to
Note: When using a jig, please work so as not to
injure chassis (net) assy and speaker box.
7 chassis block
4 connector (CN703)
3 connector (CN602)
2
6 power cord connector (CN01)
8 rear panel block
1 four screws (3.5
u
14)
5 four screws (BVTP3
u
8)
SA-WA10R
6
2-5. POWER (SW) BOARD
2-6. MAIN (SW) BOARD
3 screw (BVTP3
u
8)
3 five screws (BVTP3
u
8)
4 barrier (fuse SW)
5 fuse (H.B.C.)
(T5AH/250V)
(F01)
1 connector (CN706)
2 connector (CN704)
6 POWER (SW) board
9 two screws (BVTP3
u
8)
7 screw (BVTP3
u
8)
3 two screws (BVTP3
u
8)
1 three screws (BVTP3
u
8)
4 two screws (BVTP3
u
6)
5 shield case (main PWB SW)
4 screw (BVTP3
u
6)
4 screw (BVTP3
u
6)
7 two screws
(BVTP3
u
8)
7 three screws (BVTP3
u
8)
0 heat sink (AMP PWB SW) block
2 barrier (cord SW)
8 holder (S-AIR) block
6 two screws (BVTP2.6)
qs MAIN (SW) board
qa cushion (10
u
20)
SA-WA10R
7
SECTION 3
TEST MODE
Note: Please get remote commander from the service parts when remote
commander is necessary for the repair.
• Use the bundled remote commander when remote commander is
bundled to the repairing set.
Part No. A-1717-785-A RM-ANU066 (US and Canadian models)
Part No. A-1736-398-A RM-ANU070 (UK model)
1. COLD RESET
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn on the system.
2. Press the [PAIRING] and [
?/1
] buttons, and hold for more
than three seconds.
3. Cold reset is executed and turn off the system.
2. VERSION CHECK
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn on the system.
2. S-AIR ID slide switch select the “A”.
3. Press the [PAIRING] button, and hold for more than three sec-
3. Press the [PAIRING] button, and hold for more than three sec-
onds.
4. The color of STANDBY indicator LED is confi rmed.
RED: Normal version
ORG:
TEST
version
GRN: ROMOUT version
5. The frequency to which S-AIR indicator LED blinks is con-
fi rmed. The blinking frequency shows the place of ten of the
version.
version.
6. The frequency to which PAIRING indicator LED blinks is
confi rmed. The blinking frequency shows the place of one of
the version.
the version.
7. Example: Normal version, Ver. 0.12
STANDBY indicator LED is red, S-AIR indicator LED blink-
ing once, PAIRING indicator LED blinking twice.
ing once, PAIRING indicator LED blinking twice.
8. To release from this mode, press the [PAIRING] button, and
hold for more than three seconds.
Ver. 1.2
SA-WA10R
8
MEMO
Click on the first or last page to see other AIR-SW10TI / SA-WA10R service manuals if exist.