Sony AIR-SA15TI / AIR-SA20PK Service Manual ▷ View online
AIR-SA15Ti
4
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Guide to parts and controls
Main unit (AIR-SA15Ti/Wireless Audio Transmitter)
Front panel
Rear panel
Remote for the main unit
(RM-ANU045)
ILLUMINATION
Press to change the illumination
brightness.
brightness.
BAND
Press to select FM or AM reception
mode.
mode.
SYSTEM MENU
Press to enter the system menu.
POWER indicator
Lights up when the main unit is turned
on.
on.
iPod connector
Place an iPod on the connector to listen
to audio contents stored in the iPod.
You need to connect the supplied iPod
to audio contents stored in the iPod.
You need to connect the supplied iPod
For details on the supplied iPod Dock
Adapters, refer to the instructions
supplied with the iPod Dock Adapters.
Adapters, refer to the instructions
supplied with the iPod Dock Adapters.
S-AIR indicator
Lights up when the main unit is turned
on with the supplied wireless transceiver
inserted.
on with the supplied wireless transceiver
inserted.
Unit: TUNING/SELECT +/–
Press to tune in the desired station.
Press to select a menu item.
Press to select a menu item.
Remote: TUNING +/–
Press to tune in the desired station.
ENTER
Press to enter the settings.
Illumination
You can change the brightness using
ILLUMINATION
ILLUMINATION
.
R
Display
RB
Remote sensor
RT
ANTENNA jacks
Connect the supplied FM lead antenna
and AM loop antenna.
and AM loop antenna.
RE
POWER switch
Switch for turning the main unit on or
RG
iPod AUDIO OUT L/R jacks
iPod VIDEO OUT jack
Connect an optional AV system, such as
a TV, etc.
a TV, etc.
RH
S-AIR ID selector
Select the S-AIR ID to connect with the
sub units.
sub units.
RI
PAIRING button
Press to perform pairing.
RK
EZW-RT10 slot
Insert the supplied wireless transceiver.
RL
Buttons for controlling an iPod
(play/pause)
Press to start or pause playback.
/
Press to skip to the previous/next track.
MENU
Press to return to the previous menu.
Works much like the Menu button on
the iPod.
Works much like the Menu button on
the iPod.
/
Press to select a menu item or track for
playback.
playback.
ENTER
Press to execute the selected item or play
the selected track.
the selected track.
RM
PARTY CH
Press to select the sound source when the
S-AIR mode is set to “PARTY.”
S-AIR mode is set to “PARTY.”
X
S-AIR MODE
Press to select the S-AIR mode.
XB
Battery compartment lid
XT
PRESET +/–
Press to select a preset station.
XE
DISPLAY
Press to view the information on the
display.
display.
Display
S-AIR mode indicator
PAIRING indicator
Text information
Tuner reception mode
Tuner reception
AIR-SA15Ti
5
SECTION 3
DISASSEMBLY
•
This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
3-2. TUNER (FM/AM), PANEL TOP BLOCK
SET
3-4. MAIN BOARD
(Page
(Page
6)
3-3. TX-IF BOARD,
HOLDER
HOLDER
(SAIR)
(Page
6)
3-2. TUNER
(FM/AM),
PANEL TOP BLOCK
(Page
5)
four screws
(BVTP3
×
8)
two screws
(B2.6)
flexible flat cable (9 core)
(CN002)
RB flexible flat cable (9 core)
(US,
Canadian),
flexible flat cable (11 core)
(AEP,
UK)
unweaved cloth
R unweaved cloth
five screws
(BVTP2.6
(3CR))
two screws
(BVTP3
×
8)
RT tuner
(FM/AM)
RE panel top block
connector
(CN001)
Ver. 1.1
AIR-SA15Ti
6
3-3. TX-IF BOARD, HOLDER (SAIR)
Note: This illustration sees the panel top block from TX-IF board side.
3-4. MAIN BOARD
Note: This illustration sees the panel top block from MAIN board side.
connector
(CN603)
holder (SAIR)
TX-IF board
cushion (remote PWB)
two screws
(BVTP2.6
(3CR))
two screws
(BVTP2.6
(3CR))
panel top block
MAIN board
flexible flat cable (9 core)
(CN402)
escutcheon
panel top block
sheet (FL)
sheet (HS)
flexible flat cable (9 core)
(W002)
six screws
(BVTP2.6
(3CR))
Remove the solders.
AIR-SA15Ti
7
SECTION 4
TEST MODE
1. PANEL TEST
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [BAND] and [SYSTEM MENU] buttons,
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [BAND] and [SYSTEM MENU] buttons,
press the [PAIRING] button.
3. Then all segments of fl uorescent indicator tube are turned on
and all LEDs are lighted.
4. Press the [SYSTEM MENU] button, the model name is dis-
played on the fl uorescent indicator tube.
5. Each time [SYSTEM MENU] button is pressed, the display
changes starting from model name, destination, MC, SYS, UI,
ST and AR version this order, and returns to the model name
display.
ST and AR version this order, and returns to the model name
display.
6. Press the [ILLUMINATION] button, the version is displayed
changes to last updated date displayed.
7. Press the [BAND] button, the messages “K 0” is displayed on
the fl uorescent indicator tube. All buttons are pressed, display
becomes “K 5”. (Buttons other than [ENTER] and [PAIRING])
becomes “K 5”. (Buttons other than [ENTER] and [PAIRING])
8. To release from this mode, while pressing the [BAND] and
[SYSTEM MENU] buttons, press the [PAIRING] button.
2. FACTORY PRESET
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [BAND] and [TUNING/SELECT –] but-
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [BAND] and [TUNING/SELECT –] but-
tons, press the [PAIRING] button.
3. The messages “FACTORY” appears and initialization is per-
formed, and the messages “FM 87.50” appears.
3. S-AIR TEST
3-1. S-AIR test mode
Setting method:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [BAND] and [TUNING/SELECT +] but-
3-1. S-AIR test mode
Setting method:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [BAND] and [TUNING/SELECT +] but-
tons, press the [PAIRING] button.
3. Entered the S-AIR test mode.
4. It returns to the S-AIR test mode each item when [SYSTEM
4. It returns to the S-AIR test mode each item when [SYSTEM
MENU] button is pressed after it enters each item.
5. To release from this mode, while pressing the [BAND] and
[TUNING/SELECT +] buttons, press the [PAIRING] button.
3-1-1. I2C connection check
This mode is confi rm the I2C line between IC401 on the MAIN
board and EZW-RT10.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is confi rm the I2C line between IC401 on the MAIN
board and EZW-RT10.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “I2C”.
3. Press the [ENTER] button, the messages “OK” or “NG” is dis-
played on the fl uorescent indicator tube. When the I2C line
between IC401 on the MAIN board and EZW-RT10 is normal,
“OK” is displayed. When abnormality is found, “NG” is dis-
played.
between IC401 on the MAIN board and EZW-RT10 is normal,
“OK” is displayed. When abnormality is found, “NG” is dis-
played.
4. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-2. Quality check
This mode is radio wave sensitivity state confi rmation of EZW-
RT10.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is radio wave sensitivity state confi rmation of EZW-
RT10.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “QUALITY”.
3. Press the [ENTER] button, the messages “*** ###” is dis-
played on the fl uorescent indicator tube.
***: Minimum value (%)
###: Mean value (%)
4. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-3. Power setting
This mode is setting of radio wave output of EZW-RT10.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is setting of radio wave output of EZW-RT10.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “POWER”.
3. Press the [ENTER] button the messages “039 SET” is dis-
played on the fl uorescent indicator tube.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select the radio wave output. (OFF or 000 to 063)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-4. RF CH check
This mode is RF CH used is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is RF CH used is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “CHK RFCH”.
3. Press the [ENTER] button the messages “*** CH#” is dis-
played on the fl uorescent indicator tube.
***: ON or OFF
#: CH number used
4. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-5. ENC key change
This mode is setting of code key on/off change of EZW-RT10.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is setting of code key on/off change of EZW-RT10.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “ENC KEY”.
3. Press the [ENTER] button the messages “ON” or “OFF” is
displayed on the fl uorescent indicator tube.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select the “ON” or “OFF”.
5. Press the [ENTER] button, return to S-AIR test mode menu.
3-1-6. Version check
This mode is S-AIR version of the set connected with AIR-SA15Ti
is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is S-AIR version of the set connected with AIR-SA15Ti
is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “VER CHECK”.
3. Press the [ENTER] button, S-AIR version of the set connected
with AIR-SA15Ti is displayed on the fl uorescent indicator.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons, change the version and date displayed.
5. Press the [ENTER] button, return to S-AIR test mode each
item.