Sony AC-LF1HR / DAV-LF1H Service Manual ▷ View online
3
AC-LF1HR
SECTION 1
SERVICING NOTES
•
SERVICING POSITION
DIAT POWER board
Refer to figure, and inspect the DIAT POWER board.
SW LED board
(CN905)
(CN905)
POWER SWITCH (LFZ) board
(CN901)
(CN901)
CN907
CN903
The units that are required for the system operation check during repair service
Unit
required for checking
required for checking
Unit to be
checked
DVD player:
HCD-LF1H
Subwoofer:
SA-WSLF1H
Front speaker:
SS-TSLF1H
Center speaker:
SS-CTLF1H
Surround speaker (L):
SA-TSLF1H
AC adaptor:
AC-LF1HR
Surround speaker (R):
SS-TSLF1HW
Remote commander:
RM-ADP011
HCD-LF1H
Subwoofer:
SA-WSLF1H
Front speaker:
SS-TSLF1H
Center speaker:
SS-CTLF1H
Surround speaker (L):
SA-TSLF1H
AC adaptor:
AC-LF1HR
Surround speaker (R):
SS-TSLF1HW
Remote commander:
RM-ADP011
DVD player:
HCD-LF1H
HCD-LF1H
Subwoofer:
SA-WSLF1H
SA-WSLF1H
Front speaker:
SS-TSLF1H
SS-TSLF1H
Center speaker:
SS-CTLF1H
SS-CTLF1H
Surround speaker
(L): SA-TSLF1H
(L): SA-TSLF1H
AC adaptor:
AC-LF1HR
AC-LF1HR
Surround speaker
(R): SS-TSLF1HW
(R): SS-TSLF1HW
*1 Only the defective unit.
Units with
Units with
a
mark: The units that are required for the system operation check during repair service.
(However, there can be a case that some units of the system need to not be brought into repair shop depending on the unit.that become defective.)
*1
4
AC-LF1HR
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
AC adaptor
A
SA-TSLF1H jack (24)
B
DIR-R3 jack (33)
C
POWER indicator (29)
D
POWER (29)
SA-TSLF1H
DIR-R3
5
AC-LF1HR
SECTION 3
DISASSEMBLY
3-3. DIAT POWER BOARD
(Page 6)
3-4. POWER SWITCH (LFZ) BOARD AND
SW LED BOARD
(Page 7)
3-5.TOP CABINET
(Page 8)
3-2. CHASSIS
(Page 6)
SET
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
6
AC-LF1HR
3-3. DIAT POWER BOARD
2
cord stopper
6
DIAT POWER board
1
two screws
(+BVTP 2.6
(+BVTP 2.6
×
8)
3
two screws
(BV/RING)
4
connector
(CN903)
(CN903)
5
connector
(CN907)
5
power cord
1
six screws
(+BVTP 3
×
10)
2
chassis
4
connector
(CN901)
3
cable tie (
*
1)
cable tie
Fix the power cord with a cable tie and ensure
that the cord has no slack.
that the cord has no slack.
(
*
1)
(
*
1) : The cable tie is used only for AEP, UK and Russian models.
3-2. CHASSIS
Note:
Follow the disassembly procedure in the numerical order given.
Ver. 1.1