Sharp VC-S2000 (serv.man21) User Manual / Operation Manual ▷ View online
47
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
MORE INFORMATION ABOUT YOUR VCR
ON-SCREEN DISPLAY
All the information you need on the VCR status will be summarised on the on-screen display.
If you are recording, playing back a tape or watching a broadcast on the video channel you
can call up three standard on-screen displays. The display can be selected by pressing the
If you are recording, playing back a tape or watching a broadcast on the video channel you
can call up three standard on-screen displays. The display can be selected by pressing the
MODE OSD
button on the remote control, 1,2,3 or 4 times.
1.
AUTO
, the current mode and channel
number will be displayed for 3 seconds when an
operation or number button is pressed.
operation or number button is pressed.
2.
FULL
., all the active features will also be shown
on screen.
3.
COUNTER
, this display will show the tape
counter and amount of tape remaining.
4.
DISPLAY OFF
, this will remove the display
from the screen.
NOTES:
•
The default time and date will not be displayed if the clock has not been set.
•
The VCR will return to display
1
. each time it is switched on.
•
If you are recording from this VCR to another, make sure you remove the display from
the screen otherwise it will be recorded.
the screen otherwise it will be recorded.
1.
■
1 CH 5 9
N I CAM
S T E R EO
S T E R EO
S P
L
R
COMP
Programme number and channel
Tape Status
NICAM signal
Audio output mode
Tape speed
L1 output status Comp or Y/C
Tape remaining
Tape remaining
Time
Date
Tape counter
These
depend on
model
features
depend on
model
features
2.
■
1 CH 5 9
S U P E R
P .
ON
N I CAM
S T E R EO
S T E R EO
S P
L
R
COMP
2 2 : 0 0
R EM 1 : 0 5
9 / 0 7 0 0
0 : 0 0 . 0 0
REM 1:05
0:00.00
3.
TINS-3894 ENGLISH.book Page 47 Wednesday, September 6, 2000 11:53 AM
48
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
MORE INFORMATION ABOUT YOUR VCR
MANUFACTURERS CODES FOR SATELLITE RECEIVERS
The following table is a list of satellite manufacturers’ code numbers. Your VCR will use one of
these in order to recognise your satellite receiver. The code number must be entered at point
these in order to recognise your satellite receiver. The code number must be entered at point
11
. during installation with a satellite receiver.
Look up your make of satellite receiver.
Use the
Use the
NUMBER BUTTONS
to enter the first code number listed. For example number 8
should be entered
0 0 8
. Continue from point
12
. (
AUTO INSTALLATION
).
MANUFACTURER
CODES
Sky Digi Box
128
On Digital
PACE
122
AB SAT
123
ALBA
6,9,12,14,16,32,39,45,57,72,79,85
ALLSAT
9,14,85
AMSTRAD/FIDELITY ANKARO HANSEATIC
35,38,41,47,48,49,51,52,55,63,65,76,80,90,109,110
ARMSTRONG
2,9,12,20,22,36,41,59,73,74,82
BEST/DISKEXPRESS
75
BUSH
9,12,14,72,79
CAMBRIDGE
53
CHANNEL MASTER
12,41
DNT
2,29,31,54,58,64,87,102,118
ECHOSTAR/TECHNISAT/DNT/POLYTRON/RADEX
2,29,31,54,58,64,87,102,118
FERGUSON
9,14,16,45,85
FUBA/TRIASAT/TRIAX/FREECOM
19,37,69,71,94,104,117
G.I.JERROLD
106
GALAXIS/ALDES/PROSAT/SKYMASTER/ANARKO
86,99,78
GRUNDIG
2,16,23,44,70,91,114,119
HIRSCHMANN
2,11,24,25,30,97
HUTH
56,61,73,89
JOHANSSON/WINNERSAT
40
KATHREIN
2,9,10,16,17,18,20,22,25,26,27,36,40,59,67,68,74,82,84,88,92,100,105,108,112
LENKO
117
MASPRO
10,26,68,84,116
MATSUI
115
MORGAN
73
NETWORK
9,14
NIKKO
21,28,93,96
NOKIA
2,3,5,7,8,15,16,29,31,42,46,54,58,64,66,75,87,102,103,111, 129(dBox)
PACE/MANHATTAN/SABA
6,9,14,16,32,45,57,85,120,122,124
PALSAT/NAGAI/PALCOM
27,94
PHILLIPS/VISIOPASS/SONOLOR
2,9,20,22,36,59,74,82,114,123
SALORA/LUXOR
3,5,7,8,15,16,42,46,66,75,103
SATSIE/ STANON
9,12,14,39,72,79
SCHWAIGER/SIEMENS/TELEDIREKT
85,121
SCIENTIFIC ATALANTA
13
SEG
9,12,14,19,37,39,69,71,72,79,94,104,117
STRONG/TRISTAR
18
TATUNG/NIKKO/QUADREL
21,28,93,96
TELEVES
9,14,16,35,38,41,45,47,48,49,51,52,63,65,76,80,85,90,109,11
TPS
125,126
UNIDEN
84
VORTEC/SAMSUNG
11
WISI/TECH
1,2,4,31,33,34,43,50,60,77,81,95,98,101,107,113
ZHENDER
1,2,4,17,18,25,27,31,33,34,40,43,50,60,67,77,81,88,92,94,95,98,100,101,105,107,108
Cable TV
13
TINS-3894 ENGLISH.book Page 48 Wednesday, September 6, 2000 11:53 AM
49
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
MORE INFORMATION ABOUT YOUR VCR
SPECIFICATIONS
•
Specifications are subject to change without notice as part of our policy of
continuous improvement.
continuous improvement.
•
No liability is accepted for any inaccuracies or omissions in this publication,
although every possible care has been taken to make it complete and as
accurate as possible.
although every possible care has been taken to make it complete and as
accurate as possible.
Format:
VHS PAL/S-VHS/S-VHS ET standard
Number of heads:
Six heads
Video signal system::
PAL colour or monochrome signal:
625 lines
625 lines
Hi-Fi audio recording system:
Deep layer recording system conforming to stereo
Hi-Fi VHS standard.
Hi-Fi VHS standard.
Maximum playing time:
240 min. with E-240 video cassette in Standard Play
(SP) mode
480 min. with E-240 video cassette in Long Play (LP)
mode
720 min. with E-240 video cassette in Extended Play
(EP) mode
(SP) mode
480 min. with E-240 video cassette in Long Play (LP)
mode
720 min. with E-240 video cassette in Extended Play
(EP) mode
Tape width:
12.7 mm
Tape speed:
23.39 mm/s Standard Play (SP):
11.70 mm/s Long Play (LP)
7,8 mm/s Extended Play (EP)
11.70 mm/s Long Play (LP)
7,8 mm/s Extended Play (EP)
Antenna:
75
Ω unbalanced
Reception channels:
VHF channel A-J, UHF channel 21-69
RF output signal:
UHF channel 21-69
Power requirement:
AC 230V, 50 Hz
Power consumption:
19 W approx. (POWERSAVE
≤ 1.5W)
Operating temperature:
5 ˚C to 40 ˚C
Storage temperature:
-20 ˚C to 55 ˚C
Video input:
1.0 Vp-p, 75
Ω
Video output:
1.0 Vp-p, 75
Ω
S-Video connections:
IN/OUT
Audio input:
Line1&2: -3.8 dBs, 10 k
Ω, Line 3: -3.8 dBs, 47 kΩ
Audio output:
Line1&2: -3.8 dBs, 1 k
Ω Audio Out: -3.8 dBs, 1 kΩ
Hi-Fi audio:
Dynamic range:~ 90 dB typ. (SP);
Frequency response: 20 Hz - 20 kHz;
Wow and flutter: < 0.005% Wrm (JIS A)
Frequency response: 20 Hz - 20 kHz;
Wow and flutter: < 0.005% Wrm (JIS A)
Dimensions:
430(W) x 282.5(D) x 103.5(H) mm
Weight:
4 kg (approx.)
Supplied accessories:
75
Ω RF Connection cable, operation manual,
remote control, AA/R6/UM3 battery (x2)
TINS-3894 ENGLISH.book Page 49 Wednesday, September 6, 2000 11:53 AM
50
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
TROUBLESHOOTING
TROUBLESHOOTING
BEFORE REQUESTING SERVICE!
The following conditions do not always denote trouble. Therefore, perform the checks described
below before calling for service. If the problem cannot be corrected by the use of this guide,
remove the mains plugs from the wall socket and contact the dealer or supplier from whom the unit
was purchased in order to obtain service. Where this is not possible, please contact the telephone
number listed below, you will then be given details of how to obtain service.
below before calling for service. If the problem cannot be corrected by the use of this guide,
remove the mains plugs from the wall socket and contact the dealer or supplier from whom the unit
was purchased in order to obtain service. Where this is not possible, please contact the telephone
number listed below, you will then be given details of how to obtain service.
Tel.: 08705-274277 (office hours) or www.sharp.co.uk/support.
AREA
PROBLEM
POSSIBLE CAUSE/CURE
INITIAL
INSTALLATION
When the VCR is first
plugged in the VCR
display appears blank.
When the
STANDBY (
plugged in the VCR
display appears blank.
When the
STANDBY (
)
button is pressed the
display still appears
blank.
display still appears
blank.
• The Video may be in POWERSAVE mode. Press the
STOP (
) button to switch the VCR on then press
and hold the MENU and CHANNEL
buttons
together on the front of the VCR for 10 seconds.
Now continue from step 1 of TUNING THE TV INTO
THE VCR.
Now continue from step 1 of TUNING THE TV INTO
THE VCR.
INSTALLATION
TV will not tune in to the
VCR.
VCR.
• Check all the cables are correctly connected.
• Check your TV manual for correct tuning of your TV.
• Check your TV manual for correct tuning of your TV.
Auto Installation screen
does not appear when
the VCR is switched on
OR Auto Installation is
not complete.
does not appear when
the VCR is switched on
OR Auto Installation is
not complete.
• Reset the VCR and complete AUTO INSTALLATION
again. (Refer to VCR Reset at the back of the
book.)
book.)
POWER
Display is not working.
• Make sure the VCR is not in POWERSAVE mode.
• Make sure the power cord is plugged in.
• Make sure the wall socket has power (plug another
• Make sure the power cord is plugged in.
• Make sure the wall socket has power (plug another
appliance in).
VCR will not operate -
appears in VCR
display.
• Press the TIMER ON/OFF button to disengage
timer.
VCR will not respond to
any commands.
any commands.
• Check CHILD LOCK is not engaged.
• Safety device operating: unplug VCR for 2 hours.
• Safety device operating: unplug VCR for 2 hours.
PLAYBACK
No picture appears.
• Make sure the TV is set to the video channel.
• Check all connecting cables.
• Check all connecting cables.
Playback picture is
snowy.
snowy.
• Adjust the tracking using CHANNEL
/
buttons.
• Try another tape.
• The video heads may have been contaminated -
• The video heads may have been contaminated -
refer to a SHARP Service Facility.
RECORDING
Tape is automatically
ejected when pressing
REC (
ejected when pressing
REC (
) or TIMER
ON/OFF buttons.
• The record-protection tab has been removed.
Playback recording
does not playback in
stereo.
does not playback in
stereo.
• Ensure the VCR is connected to a stereo TV and
SCART lead.
• Programme may not carry stereo.
VIDEOPLUS does not
record desired
programme.
record desired
programme.
• Broadcast does not carry VPS/PDC signal which
alters recording time.
• Check VPS/PDC mode is switched to ON.
• Ensure date and time are correctly set on the VCR.
• Ensure date and time are correctly set on the VCR.
TAPE
TRANSPORT/
MECHANISM
Tape can not be
loaded.
loaded.
• Make sure there is no other tape in the VCR.
• Make sure you are loading the tape correctly.
• Make sure you are loading the tape correctly.
Rewind is not possible.
• Make sure the tape is not at the start.
TINS-3894 ENGLISH.book Page 50 Wednesday, September 6, 2000 11:53 AM