Sharp VC-S2000 (serv.man19) User Manual / Operation Manual ▷ View online
28
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
MODE SELECTION
16:9 PLAYBACK AND RECORDING.
This feature allows the PLAYBACK and RECORDING of wide screen format signals (16.9) which
should automatically change the picture size setting on a wide screen TV. To allow the
operation of this feature, ensure 16:9 mode is set to AUTO in the MODE menu.
A scart connection must be used between the VCR (SOCKET L1) and the TV.
During PLAYBACK of a 16:9 encoded tape the TV should switch to (Widescreen) 16:9 mode.
NOTES:
POWERSAVE.
This feature allows the VCR power consumption to be
≤1.5 Watt in
POWERSAVE mode. Auto POWERSAVE mode will engage if the VCR is not operated for 3
hours.
S-VHS.
Selecting Auto will enable your VCR to
record in Super-VHS format provided an S-VHS
cassette is being used, or in the S-VHS ET
(Expansion Technology) format when using a
VHS cassette and the S-VHS ET button on the VCR
front panel is pressed (S-VHS ET will only work in SP
mode).
L1 OUT.
You can select the output of L1 to be either a composite signal where one path is
used for the video information or a Y/C signal, where the luminance (Y) and the colour (C)
information are separated and two paths are used for the video information. This will enhance
picture quality.
L2 IN.
The input of L2 can be changed between composite input or Y/C input. Y/C input will
enhance the picture quality.
• Not all pre recorded tapes are compatible with 16:9 playback.
• This feature must be supported by TV’s equipped with 16:9 switching.
• 16:9 format recording can only be made from L2 scart input.
2 / 2
S - V H S
AU T O
O F F
L 1
OU T
COMP .
Y / C
L 2
I N
COMP .
Y / C
: S E L EC T
: CHANGE
S E T : E N T E R
ME NU : E X I T
TINS-3894 ENGLISH.book Page 28 Wednesday, September 6, 2000 11:53 AM
29
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
SEARCHING THE VIDEO TAPE
SKIP SEARCHING THE VIDEO TAPE
You can search the tape in 30 second time intervals. To do this follow the procedure below:
1.
Press
PLAY/X2
(
) to start the video tape playing.
2.
Press
SKIP SEARCH
on the remote control.
The number of times you press
SKIP SEARCH
determines the forward search time.
•
After searching, normal playback
will resume automatically.
DIGITAL PROGRAMME SEARCH SYSTEM (DPSS)
Your VCR records a marker signal on the tape at the start of each recording. These signals can
be used later to locate the starting point of a recording.
Press
DPSS
to locate a previous programme or the next programme.
For example,
1.
Load the video tape into the VCR.
2.
Press
DPSS
three times. The number 3 will appear on the on-screen display, and the
VCR will fast forward to locate the third recording after the current one.
3.
Press
DPSS
once. A -1 will appear on the on-screen display and the VCR will rewind
to locate the beginning of the current recording.
4.
To cancel the search before it has finished, press
STOP
(
) or
PLAY/X2
(
) .
NOTES:
•
Recordings must be longer than 3 minutes..
•
The starting point of playback may vary.
•
This feature will only work with video tapes recorded on a VCR with the DPSS feature.
/
-1
+1
+2
+3
RECORDING 5
RECORDING 4
RECORDING 3
RECORDING 2
RECORDING 1
DPSS Signals
Current tape position
Fast Forward
Rewind
DPSS
Number
Number
1 press = 30 seconds
2 presses = 1 minute
3 presses = 1 minute 30 seconds
4 presses = 2 minutes
2 presses = 1 minute
3 presses = 1 minute 30 seconds
4 presses = 2 minutes
TINS-3894 ENGLISH.book Page 29 Wednesday, September 6, 2000 11:53 AM
30
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
REMOTE CONTROL OPERATION OF TV
In addition to operating the VCR the remote control will also operate basic functions on TVs,
including brands other than SHARP.
including brands other than SHARP.
SETTING UP THE VCR REMOTE
CONTROL TO OPERATE THE TV
CONTROL TO OPERATE THE TV
1.
Switch on the TV. Open the door on the
remote control and point the unit at the TV.
remote control and point the unit at the TV.
2.
Hold down
TV BRAND SET
on the VCR
remote control and the appropriate
button for the TV from the list shown, for 2
seconds. For example for a SHARP TV, press
button for the TV from the list shown, for 2
seconds. For example for a SHARP TV, press
TV BRAND SET
and
1
.
3.
The TV will enter standby mode to confirm
the correct code has been entered.
the correct code has been entered.
4.
To turn the TV on from standby mode hold
TV BRAND SET
and
1
(Sharp TV) for
about 2 seconds.
CONTROLLING THE TV WITH THE VCR REMOTE CONTROL
•
TV OPERATE
Switches the TV to and from Standby Mode.
•
TV INPUT SELECT
Determines which input to the TV is to be displayed on the
screen.
screen.
•
TV CH
/
Changes the TV channels.
•
TV VOL
/
Increases or decreases the volume.
•
Certain models of TV do not use standard codes for their brand. In this case hold down
TV BRAND SET
, then press each of the buttons in the list until the TV enters stand-by
mode (You will need to reset when remote control batteries are replaced).
•
SHARP cannot guarantee the VCR remote control will operate your TV.
TV BRAND
BUTTON
TV BRAND
BUTTON
SHARP
1
TOSHIBA
9
PHILIPS
2
PANASONIC
0 or
THOMSON
3 or 4
HITACHI
INPUT SELECT
GRUNDIG
5
SANYO
MODE OSD
FERGUSON
6
JVC
DISPLAY
ITT NOKIA
7
MITSUBISHI
AUDIO OUT
SONY
8
+
TINS-3894 ENGLISH.book Page 30 Wednesday, September 6, 2000 11:53 AM
31
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
RECORDING FROM OTHER EQUIPMENT
You can record video and audio signals from various sources, for example a camcorder, onto
a video tape using your VCR.
a video tape using your VCR.
For example, recording from a camcorder connected to LINE 2 IN/DECODER on your VCR:
1.
Connect your signal source (e.g. Camcorder, Digital Camera, etc.) to the desired scart
socket on he back of the VCR using the manufacturers recommended cable (not
supplied).
socket on he back of the VCR using the manufacturers recommended cable (not
supplied).
2.
Ensure that the tape on which you
wish to record is inserted into the VCR..
wish to record is inserted into the VCR..
3.
Press
INPUT SELECT
on the remote
control until the VCR display shows
L2
.
4.
If you wish to record from a source
connected to LINE 1 IN/OUT, select
connected to LINE 1 IN/OUT, select
L1
.
5.
If you wish to record from a source
connected with audio phono leads to
the sockets on the front of the VCR
and S-VIDEO connection lead, select
connected with audio phono leads to
the sockets on the front of the VCR
and S-VIDEO connection lead, select
L3
.
6.
Press
REC
to start the recording.
NOTES:
•
There are many different ways of connecting external equipment to your VCR. Please
refer to your equipment operation manuals for further information.
refer to your equipment operation manuals for further information.
•
S-Video connection has priority over the Video connection when both are connected
to the L3 input.
to the L3 input.
•
To Record/Playback audio when connected via the S-Video input you must also
connect the audio phono leads (L3).
connect the audio phono leads (L3).
Optional SCART connection (not supplied).
Mono/Stereo Camcorder
RF OUT
SORTIE ANTENNE
ANTENNA IN
ENTREE ANTENNE
G
D
S-VIDEO OUT
SORTIE SON S-VIDEO
AUDIO
(R)
AUDIO
(L/MONO)
VIDEO
AM
PM
AM
PM
AUDIO OUT
AM/PM
LOW
ZERO BACK
INPUT SELECT
7
8
0
9
DPSS
R
SORTIE
S-VIDEO OUT
SORTIE SON S-VIDEO
LINE IN 3
VIDEO
L - AUDIO - R
S-VIDEO
INPUT SELECT
AM
PM
TINS-3894 ENGLISH.book Page 31 Wednesday, September 6, 2000 11:53 AM
Click on the first or last page to see other VC-S2000 (serv.man19) service manuals if exist.