Sharp VC-MH713 (serv.man12) User Manual / Operation Manual ▷ View online
26
If problems persist contact the SHARP Helpline on tel: 0990-274277
SPECIAL FEATURES ON YOUR VCR
CHILD LOCK
You can lock your VCR with this feature. It will work even when the VCR is in STANDBY,
preventing children from operating the VCR.
preventing children from operating the VCR.
TO ENGAGE CHILD LOCK
Press and hold the
CHILD LOCK
button on the remote control for about 2 seconds.
flashes and then
remains lit on the VCR display confirming that CHILD LOCK
has been activated.
Regardless of what other operating buttons are touched, the VCR will continue to operate in
its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.
its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.
TO DISENGAGE CHILD LOCK
Press and hold the
CHILD LOCK
button for about 2 seconds.
starts flashing and then disappears. CHILD LOCK is disengaged.
NOTES:
•
If you attempt to change modes by pressing another button while CHILD LOCK is on,
the
the
indicator will flash on the VCR display.
•
If power is interrupted for more than 60 seconds (due to power failure etc), CHILD LOCK
may disengage.
may disengage.
VC-MH713HM.book Page 26 Monday, May 8, 2000 11:53 AM
27
If problems persist contact the SHARP Helpline on tel: 0990-274277
CUSTOMISED INSTALLATION
MANUALLY TUNING A CHANNEL
•
It should not be necessary to tune in a broadcast channel manually except in unusual
circumstances such as poor signal.
circumstances such as poor signal.
To manually tune in a channel follow the procedure below.
1.
Press the
MENU
button.
2.
Press the [
/
] menu select buttons
to select SET UP. Press the
SET
button
to confirm.
3.
CHANNEL PRESET
will be
highlighted. Press the
SET
button.
4.
Press [
/
] to select
CHANNEL
.
5.
Press
[
/
]
to start tuning in either
direction. Tuning will stop when a channel
is received. If it is not the desired channel,
press
is received. If it is not the desired channel,
press
[
/
]
to continue tuning.
6.
Press [
/
] to select
FINE
TUNING
. Press and hold
[
/
]
until
the sharpest colour picture is obtained.
IMPORTANT NOTE:
7.
If you connect an independent decoder,
you must press [
you must press [
/
] to select
DECODER, then select
[
/
]
to turn
the decoder function ON.
8.
Press [
/
] to select
SKIP
.
The SKIP function determines whether the
channel can be selected when using the
CHANNEL
/
instead of the
NUMBER BUTTONS
.
9.
Press
[
/
]
to select ON or OFF for
this option.
10.
Press
SET
to confirm.
11.
Press
MENU
to leave this function.
C HANN E L
P R E S E T
C HANN E L S O R T
C L O C K
➔
P R E S E T
1
CHANN E L
CH 2 1
F I N E T UN I NG
▲
▲
D E COD E R
ON
O F F
S K I P
ON
O F F
SET
SET
CHANNEL
CHANNEL
MENU
SET
CLEAR
DISPLAY
PLUSCODE
MODE OSD
TIMER
ON/OFF
AUDIO
OUT
SKIP
SEARCH
ZERO
BACK
BACK
2
3
1
SET
Remote Control
Module 15.fm Page 27 Monday, May 8, 2000 3:05 PM
28
If problems persist contact the SHARP Helpline on tel: 0990-274277
CUSTOMISED INSTALLATION
MANUALLY SORTING CHANNELS
SORTING THE CHANNELS INTO YOUR PREFERRED ORDER
1.
Press the
MENU
button.
2.
Press the [
/
] menu select buttons to
select SET UP. Press the
SET
button
to
confirm.
3.
Press[
/
] to select CHANNEL SORT. Press
the
SET
button to confirm.
4.
The MOVE position will be highlighted. Press the
SET
button to confirm.
5.
Press [
/
/
/
]
to highlight the
channel to be moved. Press the
SET
button to confirm.
6.
Press [
/
/
/
]
to highlight the new
position for the channel. Press the
SET
button to confirm.
7.
If any more channels are to be moved, repeat
procedure from step 5.
8.
When all the channels are in your preferred
order, press the
MENU
button to leave
the MENU function.
MENU SCREEN
2.
MOD E
S E T U P
5.
MOV E
1 / 5
1 CH 2 1
7
1 3
2 CH 3 2
8
1 4
3 CH 4 3
9
1 5
4 CH 5 4
1 0
1 6
5
CH 6 5
1 1
1 7
6
1 2
1 8
6.
MOV E
1 / 5
1
CH 6 5
7
1 3
2 CH 2 1
8
1 4
3 CH 3 2
9
1 5
4 CH 4 3
1 0
1 6
5 CH 5 4
1 1
1 7
6
1 2
1 8
SET
SET
SET
SET
SET
MENU
SET
CLEAR
DISPLAY
PLUSCODE
MODE OSD
TIMER
ON/OFF
AUDIO
OUT
SKIP
SEARCH
ZERO
BACK
BACK
2
3
1
Remote Control
VC-MH713HM.book Page 28 Monday, May 8, 2000 11:53 AM
29
If problems persist contact the SHARP Helpline on tel: 0990-274277
CUSTOMISED INSTALLATION
MANUALLY SETTING THE CLOCK
This procedure will allow you to set the clock manually.
1.
Press the
MENU
button.
2.
Press the [
/
] menu select buttons to
select SET UP. Press the
SET
button to
confirm.
3.
Press [
/
] to select CLOCK. Press the
SET
button to confirm.
4.
Press [
/
] to select either 12 or 24 hour
clock.
5.
Press
[
/
]
to select TIME. Enter the time
using the
NUMBER BUTTONS
or
[
/
]. If the minutes or hours are less than
10, enter the leading 0. If using the 12 hour clock
enter AM or PM by pressing the
AM/PM
button on the remote control.
6.
Press
[
/
]
to select DATE. Enter the date
using the
NUMBER BUTTONS
or the
[
/
]. For example, for 1st April
enter
01 04
.
7.
Press
[
/
]
to select YEAR. Enter the last two
digits of the year using the
NUMBER
BUTTONS
or [
/
]. For example, for
2000 enter
00
. For the year 2001 enter
01
.
NOTE:
•
You will need to update the clock for Winter/Summer daylight saving.
S E T U P
CHANN E L P R E S E T
CHANN E L SOR T
CHANN E L SOR T
C L OCK
: S E L EC T
: CHANGE
S E T
: E N T E R ME NU : E X I T
C L OCK
MOD E
T I ME
DA T E
Y E AR
2 4 H
0 : 0 0
0 1 / 0 4
0 0
MOD E : 2 4 H / 1 2 H
: S E L EC T
: CHANGE
S E T
: E N T E R ME NU : E X I T
SET
SET
AM/PM
MENU
SET
CLEAR
DISPLAY
PLUSCODE
MODE OSD
TIMER
ON/OFF
AUDIO
OUT
SKIP
SEARCH
ZERO
BACK
BACK
2
3
1
4
7
5
8
6
9
Remote Control
Menu select buttons
➘
VC-MH713HM.book Page 29 Monday, May 8, 2000 11:53 AM
Click on the first or last page to see other VC-MH713 (serv.man12) service manuals if exist.