DOWNLOAD Sharp VC-M311AHM (serv.man2) Service Manual ↓ Size: 1.83 MB | Pages: 36 in PDF or view online for FREE

Model
VC-M311AHM (serv.man2)
Pages
36
Size
1.83 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
VCR / Operation manual
File
vc-m311ahm-sm2.pdf
Date

Sharp VC-M311AHM (serv.man2) User Manual / Operation Manual ▷ View online

4
RF OUT
SORTIE ANTENNE
ANTENNA IN
ENTREE ANTENNE
The VCR is correctly connected. 
Connect your existing aerial cable to
the ANTENNA IN socket on your
VCR.
INSTALLING YOUR VCR
CONNECTING THE CABLES
Connect your TV to the VCR using
the supplied RF connection cable,
i.e. connect the VCR RF OUT
socket to the TV AERIAL IN socket.
BACK OF
TELEVISION
Connect the VCR to the
mains
2
3
1
AERIAL OR
CATV CABLE
Optional SCART (not supplied). If you have a scart lead connect it to your
TV and LINE 1 IN/OUT socket on the VCR.
5
INSTALLING YOUR VCR
TUNING THE TV INTO THE VCR
The TV is tuned to the VCR.
1. Ensure your VCR is still in the STANDBY
mode (not low power).
2. Switch on the TV. Select an unused
channel on your TV for your VCR (there
may be a dedicated video channel refer
to your TV operation manual).
3. Press and hold the MENU button for 3
seconds. The VCR will search and
display the ideal RF channel.
4. Tune the selected channel on your TV
(refer to your TV manual) until the menu
screen appears.
5. Press SET to store the RF channel and to
place the VCR back into STANDBY.
IMPORTANT NOTE: By pressing the STANDBY button, the VCR will toggle
between STANDBY and LOW POWER modes. The VCR display will not be
illuminated in low power mode.
e.g.
T I M E R
M O D E
S E T   U P
▲ ▼  
: S E L E C T
S E T   : E N T E R     M E N U   : E X I T
MENU SCREEN
VCR
NOTE:
If you have a preferred channel, the RF channel can be set manually (21-69) after Step 3
using [
keys.
/
6
Press STOP to switch on your VCR.
This model will automatically tune in the TV channels in your area, sort them into a standard
order and set the clock.
VCR RESET
1.Press STOP to switch on the VCR.
2.Press and hold MENU and Channel
buttons together on the front of the VCR for 10
seconds.
3.The AUTO INSTALLATION screen should now be showing on your TV.
4.Follow the on-screen display to proceed with auto installation.
All the programmes should now be correctly tuned in and the clock
set. 
INSTALLING YOUR VCR
AUTO INSTALLATION
Refer to the CUSTOMISED INSTALLATION chapter if:
Your VCR could not tune automatically - due to for example poor reception.
You wish to re-arrange the channel order.
You wish to change the time on the clock or if the VCR could not set the time.
AUTO INSTALLATION
PRESS SET KEY TO START
S E T     : E N T E R         M E N U   : E X I T
If the screen above does not appear, follow
the procedure VCR RESET below.
The screen opposite should be showing on
your TV. 
Follow the instructions from the screens. 
(Auto sort will take a few minutes to complete)
On completion, the MOVE MENU will appear
showing the present channel order. Press
MENU to exit. 
If the clock is NOT automatically set, the clock
screen will appear., refer to MANUALLY
SETTING THE CLOCK
. To check the clock
has been set correctly, press DISPLAY until the
time appears on the display.
If you wish to customise the channel order refer
to MANUALLY SORTING CHANNELS.
BASIC OPERATION
IMPORTANT NOTES ON YOUR VCR AND VIDEO TAPES
VIDEO TAPES
If you use only good quality video tapes, generally it will not be necessary to clean the
video heads.
If poor quality tapes are used, or if a tape is loaded after changing VCR location, oxide
from the tape may "clog" the video heads. This will cause the playback picture to be
"snowy", or even disappear.
To remove minor contamination run a video tape in visual search mode. If this fails, you
will need to have the heads cleaned by a SHARP Service Facility. Please note, if cleaning
is necessary it is not covered by the guarantee.
Use video tapes which carry the 
mark.
BEFORE YOU PLAYBACK A VIDEO TAPE
Condensation forms in the VCR when it is moved out of or into a warm place. If you try
to playback or record, the video tape and VCR may be damaged. Turn the VCR on
and wait for about two hours until the VCR reaches room temperature before
operating.
PLAYBACK
1.Switch on your TV and select the video
channel.
2.Carefully push a pre-recorded video tape
into the tape compartment. This will switch
the VCR on.
If the record-protection tab has been
removed, the VCR will start playback as
soon as the video tape has been loaded.
3.To start playback, press PLAY/X2 (
).
Record-protection tab
HOW TO PLAYBACK A VIDEO TAPE
7
Page of 36
Display

Click on the first or last page to see other VC-M311AHM (serv.man2) service manuals if exist.