DOWNLOAD Sharp PZ-50HV2E (serv.man8) Service Manual ↓ Size: 141.58 KB | Pages: 19 in PDF or view online for FREE

Use this sustain pulse
and adjust.

Magnify 6SF block

Magnify the adjustment waveform

Magnify 6SF block

CH1 : Y SUSOUT Under (K2203), 50V/div
CH2 : Y SUSOUT Upper (K2212), 50V/div
CH4 : YPR-U1 (K2038)- Trigger, 5V/div
Trigger : 2msec delay

CH1 : Y SUSOUT Under (K2203), 50V/div
CH2 : Y SUSOUT Upper (K2212), 50V/div
CH4 : YPR-U1 (K2038)- Trigger, 5V/div
Trigger : 2msec delay

CH1 : X SUSOUT Under (K3106), 50V/div
CH2 : X SUSOUT Upper (K3105), 50V/div
CH4 : YPR-U1 (K2038)- Trigger, 5V/div
Trigger : 2msec delay

Timing adjustment of the pulse module control signal adjusts with the sustain pulse of eighth pulse (X DRIVE) and 
the ninth pulse (Y DRIVE) from the back of 6SF.

µ

µ

• Perform adjustment of waveform with a black mask screen.
• It is easy to adjust when turned field AB offset to OFF (RS-232C
  command: OCN) in adjustment.

Note:
• Sampling rate of oscilloscope sets it more than 500MS/s in order
  to perform ns order adjustment.
• Collecting calibration of probe before adjustment by all means.

• Connect GND of probe measuring waveform to SUSGND terminal
  by all means.
• Precise waveform is not displayed, and an adjustment gap may
  occur that does not collect GND properly.

When took waveform be each drive Assy unit, measure it at the 
fourth sustain pulse from the back except for a large width sustain 
pulse.
Therefore, when measured both waveform of the X and Y drives 
together, it becomes the sustain pulse of 8 and 9 pulses from the 
back.

When there is a gap with waveform of CH1 / CH2 of the part which 
enclosed in the following circle, adjust required VR to overlap the 
waveform.

Adjust with SUS-B

Adjust with SUS-U

Adjust with SUS-G

Use this sustain pulse
and adjust.

CH1 : Y SUSOUT Under (K2203), 50V/div
CH2 : Y SUSOUT Upper (K2212), 50V/div
CH4 : YPR-U1 (K2038)- Trigger, 5V/div
Trigger : 2msec delay

CH1 : Y SUS-D Under (K2225), 50V/div
CH2 : Y SUS-D Upper (K2207), 50V/div
CH4 : YPR-U1 (K2038)- Trigger, 5V/div
Trigger : 2msec delay

CH1 : Y SUS-U Under (K2224), 50V/div
CH2 : Y SUS-U Upper (K2220), 50V/div
CH4 : YPR-U1 (K2038)- Trigger, 5V/div
Trigger : 2msec delay

µ

µ

Confirm it to waveform of CH1 / CH2 of the part which enclosed in 
the following circle whether there is not a large gap.
(A gap of the quantity that shifts 20nS and adjusted remains.)

When adjust in the power supply ON state, change so that the 
quantity of gap that adjusted by temperature-rise of the pulse 
module becomes small.
Therefore, perform high power OFF (RS-232C command: DRF) 
except measurement time of waveform when adjusts, and 
adjustment error by temperature-rise does not occur.

20 - 25ns

Lower PM

Upper PM

Lower PM

Upper PM

20 - 25ns

Caution:
Not absolutely mistaking upper
and lower of waveform.

Magnify 6SF block

Magnify 6SF block

Magnify 6SF block

Magnify 6SF block

Magnify the adjustment waveform

Magnify 6SF block

Magnify 6SF block

Magnification

Magnification

Magnification

Magnification

It is necessary to readjust this adjustment when replaced the X or Y DRIVE Assy and the pulse module.

Measurement point of waveform of X and Y DRIVE Assy in timing adjustment is test pin of SUSOUT of the pulse module of
bottom of the main unit.
X DRIVE Assy : K3106     Y DRIVE Assy : K2203
Measurement screen : White mask

The measurement is easy to perform when turns field AB alternation to OFF. (RS-232C command: OCN)

Measure a sustain pulse of the fourth pulse (X DRIVE) and the fifth pulse (Y DRIVE) from the back of the fourth FS, and 
adjust.  In the start section of this sustain pulse, waveform has inflection point with the timing when SUS-B becomes ON. 
Adjust so that the voltage of this inflection point is the nearest to 150V and do not become less than 150V.
Adjustment parameter
X DRIVE: XSUSB (RS-232C command : XSB)
Y DRIVE: YSUSB (RS-232C command : YSB)

Note:
• Connect GND of probe measuring waveform to SUSGND terminal by all means.
• Precise waveform is not displayed, and an adjustment gap may occur that does not collect GND properly.

CH1 : Y SUSOUT (K2203), 50V/div
CH2 : X SUSOUT (K3106), 50V/div
CH4 : YPR-U1 (K2038)- Trigger, 5V/div
Trigger : 2msec delay

Rst

1ms/div

X

X

X

X

X

X

Y

Y

Y

Y

Y

Y

5

µ

s/div

Magnify 4SF block

Measure a waveform of this section and adjust.

Magnify the fourth pulse sustain pulse (XSUSOUT waveform) from the back of the above waveform.

1SF

2SF

3SF

4SF

150V Line

GND

50V/div

100msec/div

50V/div

100msec/div

150V Line

This broken section moves by
changing the adjustment 
parameter.

Become less than 150V.

→

 NG

VR2702

(IC5V_ADJ)

VR2201

(SUS_G_ADJ)

VR2202

(SUS_B_ADJ)

VR2203

(SUS_D_ADJ)

VR2204

(SUS_U_ADJ)

K2205

K2004

K2001

K2002

K2003

K2005

K2009

K2013

K2010

K2011

K2226

(SUS_U)

K2212

(SUSOUTB)

K2225

(SUS_D)

K2224

(SUS_U)

K2203

(SUSOUTA)

K2227

(SUS_D)

K2218

(1/2 VSUS)

K2214

(SUS_G)

K2215

(SUS_B)

K2217

(SUS_U)

K2716

(VH)

K2720

(PSUS)

K2717

(VH CONT)

K2216

(SUS_D)

VR2703

(VH_ADJ)

K2715

(YDC_DC_PD)

K2718

(VH UVP)

K2719

(VH OVP)

K2708

(VOFS)

K2705

(SUSGND)

K2702

(VSUS)

K2709

K2703

(SUSGND)

VR2701

K2222

K2211

K2710

(VOFS)

K2712

(VOFSUVP)

K2221

(+15V)

K2045

K2049
K2047

K2044

K2050
K2048
K2046

K2012

(PN MUTE)

K2038

(YPR_U1)

K2040

(YCP_MSK)

K2053

(SOFT_D)

K2041 (OFS)

K2039 (YSUS_MSK)

K2037 (YSUS_G)
K2028 (YSUS_U)

K2021

(YPR_U2)

K2029

(YSUS_D)

K2027

(YSUS_B)

K2024

(DGND)

K2101

(DEW_DET)

K2043

(DGND)

K2008

(DGND)

K2007

(DGND)

K2006

(+5V)

K2707
(IC5V)

K2714

(GNDHS)

K2704

(VF-)

K2701

(VF+)

K2706

(+14V)

K2711

(-8V)

K2713

(IC5V UVP)

VR3200

(SUS-G)

VR3201

(SUS-B)

VR3202

(SUS-D)

VR3203

(SUS-U)

K3103

(VCP_PD)

K3104

(+5V)

K3001

(+5V)

K3003

(XSUS-B)

K3015

(XSUS-MSK)

K3017

(XCP-MSK)

K3012

(XSUS-D)

K3014

(XNR-D1)

K3025

K3007

K3010

(XNR-U)

K3008

(PN_MUTE)

K3021

K3022

K3011

K3704

(VRN. CNT)

K3703

(SUS. GND)

K3701

(VSUS)

K3029

K3006

K3009

K3030

K3705

VRN UVP)

K3706

(X DC-DC PD)

K3708

(VRN_OVP)

VR3701

(VRN. ADJ)

K3707

(VRN)

K3702

(SUS. GND)

K3213

(1/2VSUS)

K3214

(SUSGND)

K3205

(SUS_D)

K3204

(SUS_U)

K3106

(SUSOUT_B)

K3102

(XNR_PD)

K3203

(1/2VSUS)

K3201

(SUSGND)

Adjusting Points

K3108

(SUS_D)

K3200

(SUS_U)

K3105

(SUSOUTA)

K3004 (XSUS-U)

K3013 (XSUS-G)

K3018 (XNR-D2)