DOWNLOAD Sharp LC-M3700 (serv.man28) Service Manual ↓ Size: 2.81 MB | Pages: 29 in PDF or view online for FREE

■ The wall-mount bracket is assembled for perpendicular installation, so to use it for tilted installation,

please follow the procedure below to set it at the installation angle.

LC-M3700 (Horizontal mount) 0° to 20°

LC-M3710 (Vertical mount)

0°

Terminal cover

Wide LCD Monitor

Temporary stand

Table

Soft cloth, etc.

Screws
(4 locations)

1 Remove the 2 vertical installation screws. These

screws are used when setting the angle in step
3.

2 Assemble the wall-mount bracket as desired as

shown in the figure. (Figure shows a 20˚ angle.)

3 Use the screws removed in Step 1 (M6 15 mm

length 

× 2 screws) and the included screws M6

15 mm length 

× 2 screws to loosely fasten the

angle-setup bracket with 4 screws. Firmly
tighten these 4 screws after the angle-setup
bracket position has been determined.

• When setting the angle of the wall-mount bracket,

be careful not to pinch your fingers, etc.

●Place the monitor (face down) on a table, etc.

covered by a thick, soft cloth for LCD panel
protection.

●Position the monitor near the edge of the table so

that the temporary stand does not hit the table, then
remove the terminal cover.

●Unfasten the 4 screws used to secure the

temporary stand in place.

5˚

10˚

15˚

20˚

As the screw hole numbers become larger 
(5, 10,15, 20), the Wide LCD Monitor will be
 tipped farther forward.

Install so that the 
angle-setup bracket 
spacers are facing 
inward.

Angle setup bracket (2 units)

Screws M6 15mm length (4 screws)

M6 30mm length

●Make sure all cables and cords are connected

and bundled (see page 27).

●Attach the terminal cover to the back of the

monitor and align the wall-mount screw holes
(Marking A: 4 locations) with the holes (4
locations) on the back of the Wide LCD Monitor.

●Use the supplied M6 30 mm length screws (4

screws) to securely fasten the wall-mount bracket
in place.

Attaching wall-mount bracket to LC-M3700 (horizontal
mount)

Wall-mount bracket

Marking A

Marking A

• Be sure to use 2 people when installing the Wide LCD Monitor to the base bracket.
• Be sure to perform Steps Å and ı below. Just performing Step Å could result in the display falling off, which is very

dangerous.

Å Hang the square holes ( ) of the wall-mount bracket on the hooks (page 22) of the base bracket.
ı Tighten the wall-mount bracket and base bracket screws.(Be sure to do this.)

Tighten from the bottom.

M5 screws 8mm length (2 screws)

Wall

Base bracket

Make sure the hooks are 
engaged.

Wide LCD

Monitor

Å

ı

M6 30mm length

Attaching wall-mount bracket to LC-M3710 (vertical
mount)

»With table stand attached

909

810

99.5

(82.1)

58.8

108.4

290

474.5

949

98.4

173.8

(173.8)

572

642

356

821.6

462.8

12

12.3

37

13

(80.5)

55.5

154

6.5

36

24

18.5

8

65

66.1

105

290

265

370

66.1

200

155

38.5

200

50

170

223

142

72.5

115

200

335.8

188.3

13

160

120

with the
door opened

Unit: mm

»With wall-mount bracket attached

(0

°)

(5

°)

(10

°)

(15

°)

(20

°)

LC-M3700 (Horizontal mount)

30

5

°

129.5

171.7782

10

°

212.9

252.5

290.4

572

129.5

122.3

114.2

105.5

96

15

°

20°

Unit: mm

949

129.5

15

Wall-mount bracket centre

Panel centre

129.5

30

(0

°)

LC-M3710 (Vertical mount)