Sharp LC-80LE646E (serv.man15) User Manual / Operation Manual ▷ View online
3
Introduction
Caring for the front panel
• Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.). To
protect the front panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth
(wet/dry sheet type cloth, etc.). This may damage the surface of the front panel.
• Wiping with a hard cloth or using strong force may scratch the surface of the front
panel.
• Use a soft damp cloth to gently wipe the front panel when it is really dirty (It may
scratch the surface of the front panel when wiped strongly).
• If the front panel is dusty, use an anti-static brush, which is commercially available, to
clean it.
WARNING
To prevent the spread of fire, keep candles or other open flames
away from this product at all times.
4
Supplied accessories
Remote control unit ( x 1)
LR03 (“AAA” size alkaline) battery ( x 2)
Pages 6 and 8
Page 6
AC cord ( x 1)
Stand unit ( x 1)
Page 9
Page 5
Wireless LAN USB adapter
(WN8522D 7-JU) ( x 1)
Page 58
Initial setup guide
(printed document)
USB memory
(operation manual)
Important safety
precautions
(printed document)
Introduction
5
Attaching the stand unit
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work, spread cushioning over the
surface on which you will be laying the TV. This will
prevent it from being damaged.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation
of the stand may result in the TV falling over.
• After attaching the stand to the TV, do not hold the
stand when you put up, set up, move or lay down the TV.
• Do not remove the stand from the TV unless using a
wall mount bracket to mount it.
1
Confirm that there are twelve screws (eight long
screws and four short screws) supplied with the
stand unit.
2
1
Set the supporting post for the stand unit
onto the polystyrene foam.
2
Attach the stand base to the supporting
post.
3
Insert and tighten the eight screws into the
eight holes on the bottom of the stand base.
• Hold the stand unit securely with one hand, and
then tighten the screws.
Stand base
Long screws
TV front
Supporting post
3
Insert the stand into the openings on the bottom
of the TV (hold the stand so it will not drop from
the edge of the base area).
• Make sure that the stand is firmly inserted into the
TV. Improper installation may result in tilting of the
TV set.
• Instead of using a soft cushion, the cardboard box
that the TV is packed in can be assembled and
used as a work table (refer to the instructions on the
box to assemble the work table).
Soft cushion
4
Insert and tighten the four screws into the four
holes on the rear of the TV.
Short screws
NOTE
• To detach the stand unit, perform the steps in reverse
order.
• A screwdriver is not supplied with this product.
• In the installation procedure, be careful not to catch
your fingers between the TV set and the floor.
Preparation
6
Using the remote control unit
Inserting the batteries
Before using the TV for the first time, insert the two supplied LR03 (“AAA” size
alkaline) batteries. When the batteries become depleted and the remote control
unit fails to operate, replace the batteries with new LR03 (“AAA” size alkaline)
batteries.
1
Open the battery cover.
2
Insert the two supplied LR03 (“AAA” size alkaline)
batteries.
• Place batteries with their terminals corresponding to the (e)
and (f) indications in the battery compartment.
3
Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to
follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different
characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of
new batteries or cause chemical leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries
can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to
storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove
the batteries from it.
• When replacing the batteries, use alkaline batteries instead of zinc-carbon ones.
Note on disposing batteries
The batteries provided contain no harmful materials such as cadmium, lead or
mercury.
Regulations concerning used batteries stipulate that batteries may no longer be
thrown out with the household rubbish. Deposit any used batteries free of charge
into the designated collection containers set up at commercial businesses.
Angle of the remote control unit
Use the remote control unit by pointing it towards the remote control sensor.
Objects between the remote control unit and sensor may prevent proper
operation.
5 m
Remote control sensor
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock. In
addition, do not expose the remote control unit to
liquids, and do not place in an area with high humidity.
• Do not install or place the remote control unit under
direct sunlight. The heat may cause deformation of the
unit.
• The remote control unit may not work properly if the
remote control sensor of the TV is under direct sunlight
or strong lighting. In such cases, change the angle of
the lighting or the TV, or operate the remote control unit
closer to the remote control sensor.
Preparation
Click on the first or last page to see other LC-80LE646E (serv.man15) service manuals if exist.