Sharp LC-70LE857E (serv.man4) User Manual / Operation Manual ▷ View online
3
Introduction
Caring for the front panel
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.). To
protect the front panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth
(wet/dry sheet type cloth, etc.). This may damage the surface of the front panel.
(wet/dry sheet type cloth, etc.). This may damage the surface of the front panel.
• Wiping with a hard cloth or using strong force may scratch the surface of the front
panel.
• Use a soft damp cloth to gently wipe the front panel when it is really dirty (It may
scratch the surface of the front panel when wiped strongly).
• If the front panel is dusty, use an anti-static brush, which is commercially available, to
clean it.
WARNING
To prevent the spread of fire, keep candles or other open flames
away from this product at all times.
away from this product at all times.
3D glasses (AN-3DG40, sold separately)
Prevention of accidental ingestion
• Keep the accessory out of the reach of small children. Small children can accidentally
swallow these parts.
• If a child accidentally swallows any of these parts, seek immediate medical attention.
Do not disassemble
• Do not disassemble or modify the 3D glasses except when recycling the batteries.
Do not modify the 3D glasses.
Caution for lithium battery
• Batteries must not be exposed to excessive heat such as direct sunlight or fire.
• Replace only with the same or equivalent type of battery. The battery may explode if
• Replace only with the same or equivalent type of battery. The battery may explode if
improperly replaced.
• Take care not to reverse the battery poles (+ and –) when loading the battery. Follow
the correct procedure when loading the battery. Loading the battery incorrectly may
damage the battery or cause it to leak battery fluid, which could result in a fire, injury
or damage.
damage the battery or cause it to leak battery fluid, which could result in a fire, injury
or damage.
Handling the 3D glasses
• Do not drop, exert pressure on, or step on the 3D glasses. Doing so may damage the
glass section, which may result in injury.
• Be careful not to trap your finger in the hinge section of the 3D glasses. Doing so
may result in injury.
• Pay special attention when children are using this product.
Using the 3D glasses
• Do not drop, exert pressure on, or step on the 3D glasses. Doing so may damage the
glass section, which may result in the risk of injury.
• Use the 3D glasses only for the specified purpose.
• Do not move around while wearing the 3D glasses. The surrounding area appears
• Do not move around while wearing the 3D glasses. The surrounding area appears
dark, which may result in falling or other accidents that may cause injury.
Caring for the 3D glasses
• Use only the cloth provided with the 3D glasses to clean the lenses. Remove dust
and soil from the cloth. Any dust or other soiling on the cloth may result in scratches.
Do not use solvents such as benzene or thinners as doing so may damage the
coating.
Do not use solvents such as benzene or thinners as doing so may damage the
coating.
• When cleaning the 3D glasses, take care not to allow water or other fluids to come
into contact with the glasses.
• Always store the 3D glasses in the case provided when not in use.
• When storing the 3D glasses, avoid very humid or hot locations.
• When storing the 3D glasses, avoid very humid or hot locations.
Viewing 3D images
• If you experience dizziness, nausea, or other discomfort while viewing 3D images,
discontinue use and rest your eyes.
• Do not use the 3D glasses if they are cracked or broken.
4
Supplied accessories
Remote control unit ( x 1)
“AAA” size battery ( x 2)
Pages 7 and 9
Page 7
Stand unit ( x 1)
For 60/70 inch models
For 80 inch models
Page 5
Page 6
Wireless LAN USB adapter
(WN8522D 7-JU) ( x 1)
AC cord ( x 1)
(For 80 inch models only)
Page 65
Page 10
Initial setup guide
(printed document)
(printed document)
Important safety
precautions
(printed document)
precautions
(printed document)
Optional accessories
The listed optional accessories are available for this LCD colour TV. Please
purchase them at your nearest shop.
purchase them at your nearest shop.
• Additional optional accessories may be available in the near future. When purchasing,
please read the newest catalogue for compatibility and check the availability.
No.
Part name
Part
number
Notes
1
Wall mount bracket
(For 60/70 inch models)
(For 60/70 inch models)
AN-52AG4
The mark “c” indicates the location of
the centre of the TV screen.
the centre of the TV screen.
2
3D glasses
AN-3DG40
Refer to the operation manual of the 3D
glasses for details regarding usage.
glasses for details regarding usage.
Introduction
5
Attaching the stand unit (for 60/70 inch models)
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work, spread cushioning over the
• Before performing work, spread cushioning over the
surface on which you will be laying the TV. This will
prevent it from being damaged.
prevent it from being damaged.
• Be sure that two or more persons attach the stand.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation
• Be sure to follow the instructions. Incorrect installation
of the stand may result in the TV falling over.
• After attaching the stand to the TV, do not hold the
stand when you put up, set up, move or lay down the TV.
• Do not remove the stand from the TV unless using a
wall mount bracket to mount it.
1
Confirm that there are 9 screws (four M6 screws,
four M5 screws and one M4 screw) supplied
with the stand unit.
four M5 screws and one M4 screw) supplied
with the stand unit.
2
Attach the supporting post to the stand base.
1
Insert the claws of the supporting post into
the stand base.
the stand base.
2
Secure the post and the base using the M6
screws (length: 16 mm) and a screwdriver.
screws (length: 16 mm) and a screwdriver.
M6 screws
NOTE
• Tighten the screws to the holes of the mark “b”.
3
Insert the stand into the openings on the bottom
of the TV (hold the stand so it will not drop from
the edge of the base area).
of the TV (hold the stand so it will not drop from
the edge of the base area).
• Make sure that the stand is firmly inserted into the
TV. Improper installation may result in tilting of the
TV set.
TV set.
Soft cushion
4
Insert and tighten the M5 screws (length: 14 mm)
into the holes on the rear of the TV.
into the holes on the rear of the TV.
M5 screws
5
Attaching the stand cover.
1
Insert the stand cover.
2
Insert and tighten the M4 screw (length:
8 mm) into the holes of the stand cover.
8 mm) into the holes of the stand cover.
• Tighten the screw by pressing the bottom of the
stand base to the TV side.
M4 screw
NOTE
• To detach the stand unit, perform the steps in reverse
order.
• A screwdriver is not supplied with this product.
• In the installation procedure, be careful not to catch
• In the installation procedure, be careful not to catch
your fingers between the TV set and the floor.
• The TV can be rotated up to 20 degrees to the right and
left.
Preparation
6
Attaching the stand unit (for 80 inch models)
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work, spread cushioning over the
• Before performing work, spread cushioning over the
surface on which you will be laying the TV. This will
prevent it from being damaged.
prevent it from being damaged.
• Be sure that two or more persons attach the stand.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation
• Be sure to follow the instructions. Incorrect installation
of the stand may result in the TV falling over.
• After attaching the stand to the TV, do not hold the
stand when you put up, set up, move or lay down the TV.
• Do not remove the stand from the TV unless using a
wall mount bracket to mount it.
1
Confirm that there are 14 screws (eight M6
screws, four M5 screws and two M4 screws)
supplied with the stand unit.
screws, four M5 screws and two M4 screws)
supplied with the stand unit.
2
Attach the supporting post to the stand base.
1
Insert the claws of the supporting post into
the stand base.
the stand base.
2
Secure the post and the base using the M6
screws (length: 20 mm) and a screwdriver.
screws (length: 20 mm) and a screwdriver.
M6 screws
NOTE
• Tighten the screws to the holes of the mark “b”.
3
Insert the stand into the openings on the bottom
of the TV (hold the stand so it will not drop from
the edge of the base area).
of the TV (hold the stand so it will not drop from
the edge of the base area).
• Make sure that the stand is firmly inserted into the
TV. Improper installation may result in tilting of the
TV set.
TV set.
• Instead of using a soft cushion, the cardboard box
that the TV is packed in can be assembled and
used as a work table (refer to the instructions on the
box to assemble the work table).
used as a work table (refer to the instructions on the
box to assemble the work table).
Soft cushion
4
Insert and tighten the M5 screws (length: 14 mm)
into the holes on the rear of the TV.
into the holes on the rear of the TV.
M5 screws
5
Attaching the stand cover.
1
Insert the stand cover.
2
Insert and tighten the M4 screws (length:
8 mm) into the holes of the stand cover.
8 mm) into the holes of the stand cover.
• Tighten the screws by pressing the bottom of
the stand base to the TV side.
M4 screws
NOTE
• To detach the stand unit, perform the steps in reverse
order.
• A screwdriver is not supplied with this product.
• In the installation procedure, be careful not to catch
• In the installation procedure, be careful not to catch
your fingers between the TV set and the floor.
• The TV can be rotated up to 20 degrees to the right and
left.
Preparation
Click on the first or last page to see other LC-70LE857E (serv.man4) service manuals if exist.