Sharp LC-50LE771E Service Manual ▷ View online
45
LC-42/50LE772
LC-42/50LE771
7. 3 POWER STAGE
16
4. POWER STAGE
Figure 7: Power socket and options.
Power socket is used for taking voltages which are 3.3V, 12V, 5V and 24V(VDD_Audio).
These voltages are produced in power card. Also socket is used for giving dimming, backlight
and standby signals with power card. İt is shown in figure 7.
Figure 8: General illustration of voltage stages on main board.
24V(VDD_Audio) goes directly to the audio side, through power socket other incoming
voltages from power card are converted several voltages, shown in figure 8.
3. POWER STAGE
46
LC-42/50LE772
LC-42/50LE771
17
List of the components are:
SW1 and SW2 → FDC642P
DC/DC3, DC/DC1 and DC/DC4 → TPS65251
DC/DC2 → MP1484
LDO1 → APL5910
LDO2 → LM1117
FDC642P
General Description and Features
TPS65251
a) General Description
The TPS65251 features three synchronous wide input range high efficiency buck
converters. The converters are designed to simplify its application while giving the designer
the option to optimize their usage according to the target application.
The converters can operate in 5-, 9-, 12- or 15-V systems and have integrated power
transistors. The output voltage can be set externally using a resistor divider to any value
between 0.8 V and close to the input supply. Each converter features enable pin that allows a
delayed start-up for sequencing purposes, soft start pin that allows adjustable soft-start time
by choosing the soft-start capacitor, and a current limit (RLIMx) pin that enables designer to
adjust current limit by selecting an external resistor and optimize the choice of inductor. The
current mode control allows a simple RC compensation.
The switching frequency of the converters can either be set with an external resistor
connected to ROSC pin or can be synchronized to an external clock connected to SYNC pin if
needed. The switching regulators are designed to operate from 300 kHz to 2.2 MHz. 180° out
of phase operation between Buck 1 and Buck 2, 3 (Buck 2 and 3 run in phase) minimizes the
input filter requirements.
TPS65251 features a supervisor circuit that monitors each converter output. The PGOOD
pin is asserted once sequencing is done, all PG signals are reported and a selectable end of
reset time lapses. The polarity of the PGOOD signal is active high.
17
List of the components are:
SW1 and SW2 → FDC642P
DC/DC3, DC/DC1 and DC/DC4 → TPS65251
DC/DC2 → MP1484
LDO1 → APL5910
LDO2 → LM1117
FDC642P
General Description and Features
TPS65251
a) General Description
The TPS65251 features three synchronous wide input range high efficiency buck
converters. The converters are designed to simplify its application while giving the designer
the option to optimize their usage according to the target application.
The converters can operate in 5-, 9-, 12- or 15-V systems and have integrated power
transistors. The output voltage can be set externally using a resistor divider to any value
between 0.8 V and close to the input supply. Each converter features enable pin that allows a
delayed start-up for sequencing purposes, soft start pin that allows adjustable soft-start time
by choosing the soft-start capacitor, and a current limit (RLIMx) pin that enables designer to
adjust current limit by selecting an external resistor and optimize the choice of inductor. The
current mode control allows a simple RC compensation.
The switching frequency of the converters can either be set with an external resistor
connected to ROSC pin or can be synchronized to an external clock connected to SYNC pin if
needed. The switching regulators are designed to operate from 300 kHz to 2.2 MHz. 180° out
of phase operation between Buck 1 and Buck 2, 3 (Buck 2 and 3 run in phase) minimizes the
input filter requirements.
TPS65251 features a supervisor circuit that monitors each converter output. The PGOOD
pin is asserted once sequencing is done, all PG signals are reported and a selectable end of
reset time lapses. The polarity of the PGOOD signal is active high.
47
LC-42/50LE772
LC-42/50LE771
18
TPS65251 also features a light load pulse skipping mode (PSM) by allowing the LOW_P
pin tied to V3V. The PSM mode allows for a reduction on the input power supplied to the
system when the host processor is in stand-by (low activity) mode.
b) Features
• Wide Input Supply Voltage Range (4.5 V - 18 V)
• 0.8 V, 1% Accuracy Reference
• Continuous Loading: 3 A (Buck 1), 2 A (Buck 2 and 3)
• Maximum Current: 3.5 A (Buck 1), 2.5 A (Buck 2 and 3)
• Adjustable Switching Frequency 300 kHz - 2.2 MHz Set By External Resistor
• Dedicated Enable for Each Buck
• External Synchronization Pin for Oscillator
• External Enable/Sequencing and Soft Start Pins
• Adjustable Current Limit Set By External Resistor
• Soft Start Pins
• Current-Mode Control With Simple Compensation Circuit
• Power Good
• Optional Low Power Mode Operation for Light Loads
• QFN Package, 40-Pin 6 mm x 6 mm RHA
APPLICATIONS
• Set Top Boxes
• Blu-ray DVD
• Security Camera
• Car Audio/Video
• DTV
• DVR
Table: Recommended operating conditions
Figure: Pin Description
48
LC-42/50LE772
LC-42/50LE771
19
Table: Pin functions.
Click on the first or last page to see other LC-50LE771E service manuals if exist.