DOWNLOAD Sharp LC-50LE751K (serv.man9) Service Manual ↓ Size: 492.41 KB | Pages: 8 in PDF or view online for FREE

Model
LC-50LE751K (serv.man9)
Pages
8
Size
492.41 KB
Type
PDF
Document
Service Manual / Technical Bulletin
Brand
Device
TV / LCD / NVM recovery process
File
lc-50le751k-sm9.pdf
Date

Sharp LC-50LE751K (serv.man9) Service Manual / Technical Bulletin ▷ View online

LCD 2013 12 06 
 
Date of Issue: 23
rd
 December 2013      
         
Classification: 
White 
LCD TELEVISION TECHNICAL BULLETIN
 
Page 5 of 8 
 
 
Sharp Electronics (UK) Limited 
Reference 
– RG23122013-1
 
Revision - 1 
 
White 
– Carry out as required 
Yellow 
– Carry out as required and whenever the unit comes in for service 
 Red 
– Carry out on all units   
Explanation of RS-232 codes  
 
Code 
Detail of Command 
KMOD1056 
Put’s the main board into “K” mode (Service mode) 
KMOD8723 
Exit “K” mode (Service mode) 
KPSZ0039 
Set’s panel size to 39” 
KPSZ0050 
Set’s panel size to 50” 
KPSZ0060 
Set’s panel size to 60” 
INIT0*** 
Perform Factory Initialization 
MSET0004 
Enter White Balance mode 
MSET0003 
Force White Balance to setting 1 
  * is a space. RS-232 commands need to have a total of 8 characters. 
  All letters must be in capital. 
 
Adjustment Advice 
Fault condition 
– After replacing the main board, the unit is stuck in a yellow “K” mode 
(Service mode). 
Possible cause 
– With the “K” mode on-screen, check the “W” setting. If the digit is 0, 
you need to initialize the white balance.  
Solution 
– Initialize white balance. 
 
Procedure: 
1.  Setup serial port (Ensure Baud Rate speed is 115000). 
2.  Check communication 
– Send a wrong code.  
Example 
– Send “AAA” , TV should returns “ERR”. 
3.  Type 
KMOD1056
 (Enter in K mode). 
4.  Type 
MSET0004
 (Enter white balance mode). 
5.  Type 
MSET0003
 (Change white balance setting to 1). 
6.  Type 
INIT0***
 (Perform a factory initialisation). 
7.  Turn mains AC OFF/ON. 
LCD 2013 12 06 
 
Date of Issue: 23
rd
 December 2013      
         
Classification: 
White 
LCD TELEVISION TECHNICAL BULLETIN
 
Page 6 of 8 
 
 
Sharp Electronics (UK) Limited 
Reference 
– RG23122013-1
 
Revision - 1 
 
White 
– Carry out as required 
Yellow 
– Carry out as required and whenever the unit comes in for service 
 Red 
– Carry out on all units   
Adjustment Advice
…cont 
Fault condition - No backlight, no picture, blue LED. 
Possible cause - Inch size setup has been corrupted.  
Solution - Setup inch size 
 
Procedure: 
8.  Setup serial port (Ensure Baud Rate speed is 115000). 
9.  Check communication 
– Send a wrong code.  
Example 
– Send “AAA” , TV should returns “ERR”. 
10. Type 
KMOD1056
 (enter in K mode). 
11. Type 
KPSZ00**
 (Set panel size. ** = 39, 50 or 60). 
12. Turn mains AC OFF/ON. 
13. If the TV is switches on properly, then type 
KMOD8723
 (exit K mode) or 
INIT0***
 
(Perform a factory initialisation). 
 
Fault condition - No backlight, no picture, blue LED, red LED. 
Possible cause - All NVM data has been corrupted. 
Solution: Re-write NVM. 
 
Procedure: 
1.  Setup serial port (Ensure Baud Rate speed is 115000). 
2.  Check communication 
– Send a wrong code.  
Example 
– Send “AAA” , TV should returns “ERR”. 
3.  Type 
KMOD1056
 (enter in K mode). 
4. 
If TV is 50”, then type 
KPSZ0060 
 
5.  Turn mains AC OFF/ON. 
6.  Type 
KPSZ0050
 (When you input the correct settings, all positions in the NVM are 
re-written after mains AC off/on). 
7.  Turn mains AC OFF/ON. 
8.  If TV is switched on properly, then type 
KMOD8723
 (exit K mode) or 
INIT0***
 
(Perform a factory initialisation). 
 
LCD 2013 12 06 
 
Date of Issue: 23
rd
 December 2013      
         
Classification: 
White 
LCD TELEVISION TECHNICAL BULLETIN
 
Page 7 of 8 
 
 
Sharp Electronics (UK) Limited 
Reference 
– RG23122013-1
 
Revision - 1 
 
White 
– Carry out as required 
Yellow 
– Carry out as required and whenever the unit comes in for service 
 Red 
– Carry out on all units   
Manually re-write NVM 
If you need to manually re-write the NVM, download and extract the NVM files from 
the Technical Website. 
In the extracted files you will find 
Loewe.EaRom.exe
 
 
Procedure: 
1.  Connect the television to the same network as the PC is connected to and read the 
IP address of the television. You can find this information at:  
Menu -> SETUP -> Multimedia/Network -> Network settings -> Networking. 
2.  R
ead the line “IP address” and write this IP number in the box “TV” overwriting the 
IP that appears where the red arrow is. 
 
 
LCD 2013 12 06 
 
Date of Issue: 23
rd
 December 2013      
         
Classification: 
White 
LCD TELEVISION TECHNICAL BULLETIN
 
Page 8 of 8 
 
 
Sharp Electronics (UK) Limited 
Reference 
– RG23122013-1
 
Revision - 1 
 
White 
– Carry out as required 
Yellow 
– Carry out as required and whenever the unit comes in for service 
 Red 
– Carry out on all units   
3.  To read the NVM master file, use the o
ption “Open…” (File) and select the proper 
file according to model / inches in the extracted file. 
4.  To write the NVM of television
, use the option “Write” (EAROM); wait for a few 
seconds, then a message will appear at the bottom side of the screen program 
telling that writing has been successful.  
 
Notes: 
 
To write NVM of 39”: Write the master NVM file of the 50” and change the inches 
from K mode by RS-232 sending the following comand: (
KPSZ0039
).   
You can also change it from service mode: Panel inches  -> 3
9”. 
  The NVM data is the same for LE75x and LE65x, but by default the name in NVM 
data is LE75x.  
To change the model to LE65x, you should changed by RS-232 sending the 
command (
KRCT1
). 
 
Unit does not respond to RS-232 or LAN EEPROM recovery 
If the advice provided does not resolve the issue, you will need to investigate the 
circuit and determine the component failure. 
 
 
Page of 8
Display

Sharp LC-50LE751K (serv.man9) Service Manual / Technical Bulletin ▷ Download