Sharp LC-46LD266K (serv.man2) Service Manual ▷ View online
5
LC-46LD264
LC-46LD265
LC-46LD266
PRECAUTIONS FOR USING LEAD-FREE SOLDER
1 Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead
wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you to
use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our
service station or service branch in your area.
2 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder by
40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended
period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be
exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and
off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every
use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing.
6
LC-46LD264
LC-46LD265
LC-46LD266
END OF LIFE DISPOSAL
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires
proper treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used
electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local
retailer may also take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately
beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery
and recycling and thus prevent potential negative effects on the environment and human health which could otherwise
arise due to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for
the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local
collection facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used
products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
Attention: Your product
is marked with this
symbol. It means that
used electrical and
electronic products
should not be mixed
with general household
waste. There is a
separate collection
system for these
products.
is marked with this
symbol. It means that
used electrical and
electronic products
should not be mixed
with general household
waste. There is a
separate collection
system for these
products.
End of life disposal
The battery supplied with this product contains traces of Lead.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste!
There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with
legislation. Please contact your local authority for details on the collection and recycling schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.
28
7
LC-46LD264
LC-46LD265
LC-46LD266
OPERATION MANUAL
Introduction
4 -
Remote control unit
26
27
28
28
1
2
3
4
5
6
4
5
6
7
8
9
9
10
11
12
13
14
15
16
13
14
15
16
17
18
19
20
21
19
20
21
22
23
24
24
25
29
30
31
30
31
1.
I
(POWER)
Press to turn the LCD TV on or to
enter standby mode�
2. 0-9 DIGIT BUTTONS
Press to select a TV channel directly�
3. PRE PR
Press to display the previous
selected TV channel�
4. ECO
Press to switch
Power Saving
between
On and Off�
5.
Press to display programme
information, if available�
6.
Press to toggle audio on and off�
You can also press
(k/l) to
restore the previous volume level�
7. P ( / )
Press to select programme channel�
8. VIDEO (ADJ)
Press to set the LCD TV to a
predefined picture setting:
Dynamic / Standard / Movie /
Power Saver�
9. SLEEP
Press to turn the LCD TV off within
an amount of time (10 ~ 120
minutes�)
10.
Press to navigate and confirm your
selection�
11. EXIT
Press to exit the LCD TV OSD or
return to the previous layer�
12. R/G/Y/B (Colour Button)
Press to select the pictures with
various colours of text� Different
channels display different functions�
13. SIZE
Press to change the font size: Full
screen, Top half, and Bottom half�
14. SUBPAGE
Press to select the subpage
when the current page contains
subpage(s)�
15. REVEAL
Reveal hidden information such as
answers to a quiz�
16. FREEZE
Press to freeze a moving image on
the screen (only available when your
input source is TV)�
The SCART output signal will also
be frozen when you are watching
digital channels�
Caution: Do not freeze the video
image for long periods of time,
as this may damage the LCD TV
screen�
17.
(INPUT SOURCE)
Press to select an input source�
18. EPG
Press to display electronic
programme guide when watching
digital channels�
19. PR LIST
Press to display channel list�
20. DTV/ATV
Press to switch between
DTV and
ATV�
21.
(View Mode)
Press to select picture formats:
Auto / 16:9 / 14:9 / Full Screen /
4:3 / Zoom1 / Zoom2 / Zoom3�
22.
(k/l)
Press to adjust the volume�
23. AUDIO (ADJ)
Press to set the LCD TV to a
predefined sound setting:
User /
Music / Speech�
24. DUAL
Press to select
MONO / STEREO /
DUAL 1 / DUAL 2 for ATV channel�
Press to select Audio language for
DTV channel�
25. OK
Press to activate a setting�
26. MENU
Press to activate the LCD TV OSD�
27. SUBTITLE
For DTV, press to toggle
off / between available subtitle
languages�
For ATV, press to toggle off /
between available subtitle pages in
Teletext�
28. TELETEXT
Press to activate Teletext�
Press again to activate Teletext
with TV�
Press again to turn off Teletext�
29. HOLD
Press to stop the scrolling of pages�
The text decoder stops receiving
data�
30. INDEX
Press to return to page 100 or the
index page; and then press 0 to 9�
The teletext page will be numbered
and added to the page you select or
the secondary item�
31. In USB mode:
(You need to programme the setting
with remote control to control
connected devices�)
Press to skip back to the previous
title or track�
Press to stop playback�
Press to start/pause playback�
Press to skip forward to the next title
or track�
8
LC-46LD264
LC-46LD265
LC-46LD266
Operation Manual (Continued)
Control Button - Rear view
P
32”
42”
50”
46”
AUDIO
DIGITAL
AUDIO
COMPONENT
VIDEO IN
LD166 / LD266
ENTERNET
Common Interface slot
L/R AUDIO INPUT
Headphone Output
USB
COMPONENT
(VIDEO INPUT)
Digital Audio out
Tuner Input
SCART
(CVBS Tuner out)
Programme
(Channel)
Volume
Menu
Input Source
Power
HDMI 2 HDMI 1
(ARC)
VIDEO INPUT
Front view
32”
42”
50”
46”
Power indicator
Remote control sensor
Click on the first or last page to see other LC-46LD266K (serv.man2) service manuals if exist.