Sharp LC-40LE811E (serv.man6) Service Manual ▷ View online
LC-40/46LE810E, LC-40/46LX810E
2 – 2
2. LC-46LE810E/LX810E
Attach LED-PWB & Angle with screw.
Angle(A) x2
LANGT0061TPZZ
Angle(B) x2
LANGT0060TPZZ
LED-PWB x4
RUNTK4461TPZZ
Align the directions.
Hook part of angle and
connector of LED-PWB.
Align the directions.
Hook part of angle and
connector of LED-PWB.
Screw x44
LX-SZ2203TPZZ
Note
Use same rank LED-PWB in a module.
Use ionized air blowers.
Use conductive wristband or conductive shoes.
Use JIG for hold angle.
Don't touch LED surface as much as possible.
Don't touch LED with screw or driver bit.
Use ionized air blowers.
Use conductive wristband or conductive shoes.
Use JIG for hold angle.
Don't touch LED surface as much as possible.
Don't touch LED with screw or driver bit.
Ionized air blowers
stamp "0061"
stamp "0060"
reverse side
of connector
of connector
Identify the LED rank by the
alpha-numerical description
of 2 digits.
alpha-numerical description
of 2 digits.
(For example "01")
reverse side
of connector
of connector
2 digits
Attach LED-PWB Angle with screw.
S-PWB side
Angle(A) x2
LANGT0061TPZZ
Angle(B) x2
LANGT0060TPZZ
screw x32
LX-BZ2103TPZZ
screw lock (blue)
Note
Use same rank LED-PWB in a module.
Use ionized air blowers.
Use conductive wristband or conductive shoes.
Don't touch LED surface as much as possible.
Don't touch LED with screw or driver bit.
Use ionized air blowers.
Use conductive wristband or conductive shoes.
Don't touch LED surface as much as possible.
Don't touch LED with screw or driver bit.
Ionized air blowers
stamp "0061"
stamp "0060"
stamp "0061"
stamp "0060"
Note of tightening
Except as otherwise noted in
no particular order tightening.
1st
Positioning hole
1st
Positioning hole
1st
Positioning hole
1st
Positioning hole
LC-40/46LE810E, LC-40/46LX810E
2 – 3
[2] Peel off the Lamination Film
1. LC-40LE810E/LX810E
1. Peel off the back side laminetion film
GND
Back side
Ionized air blowers
Caution
* Ground S-PWB connectors while peeling off lamination film.
* Use a ionized air blower while peeling off lamination film.
* Ground S-PWB connectors while peeling off lamination film.
* Use a ionized air blower while peeling off lamination film.
Wind from the blower should cover whole surface of panel.
* Never touch polarizer surface after lamination film is removed.
Claw fit 4 points
Check
(upper claw 4 points)
P-chassis(B) side
S-PWB side
Fit
2. Fit the panel
3. Fit the S-PWB to the P-chassis
4. Peel off the front side lamination film
Ionized air blowers
S-PWB side
GND
Front side
Caution
* Ground S-PWB connectors while peeling off lamination film.
* Use a ionized air blower while peeling off lamination film.
* Ground S-PWB connectors while peeling off lamination film.
* Use a ionized air blower while peeling off lamination film.
Wind from the blower should cover whole surface of panel.
* Never touch polarizer surface after lamination film is removed.
Panel reference point
Panel reference point
LC-40/46LE810E, LC-40/46LX810E
2 – 4
2. LC-46LE810E/LX810E
Back side
GND
Peel off the back side laminetion film
Fit the panel.
Fit the S-PWB to the P-chassis hook.
Front side
Panel reference point
S-PWB side
stamp
S-PWB hook point (left side, same L/R)
Check the fit to P chassis hook.
(
part lower hook 5 places, total 10 places L/R )
Peel off the front side lamination film
GND
S-PWB side
Caution
* Ground S-PWB connectors while peeling off lamination film.
* Use a ionized air blower while peeling off lamination film.
* Ground S-PWB connectors while peeling off lamination film.
* Use a ionized air blower while peeling off lamination film.
Wind from the blower should cover whole surface of panel.
* Never touch polarizer surface after lamination film is removed.
Panel reference point
Ionized air blowers
Ionized air blowers
Caution
* Ground S-PWB connectors while peeling off lamination film.
* Use a ionized air blower while peeling off lamination film.
* Ground S-PWB connectors while peeling off lamination film.
* Use a ionized air blower while peeling off lamination film.
Wind from the blower should cover whole surface of panel.
* Never touch polarizer surface after lamination film is removed.
* Don't mistake use the panel for other models.
* Don't mistake use the panel for other models.
(Because there is very similar front polarizers.)
PARTS GUIDE
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
for after sales service only.
The contents are subject to change without notice.
LC-40/46LE810E, LC-40/46LX810E
PartsGuide
[1] LCD PANEL MODULE
(LC-40LE810E/LX810E)
[2] LCD PANEL MODULE
(LC-46LE810E/LX810E)
CONTENTS
No. S00N140LE810E
LCD COLOUR TELEVISION
LC-40LE810E
LC-46LE810E
LC-40LX810E
LC-46LX810E
MODELS
Click on the first or last page to see other LC-40LE811E (serv.man6) service manuals if exist.