Sharp LC-37RD2E (serv.man11) User Manual / Operation Manual ▷ View online
3
Supplied accessories
Quick guide
Remote control unit (g1)
AC cord (g1)
Pages 5 and 6
U.K. type 3-pin AC cord is only
included with models LC-32RD2E,
LC-37RD2E,LC-42RD2E.
Page 4
• “AAA” size battery (g2) ...... Page 5
Cable clamp
(Smallg1, Largeg1)
Page 4
Cable tie (g1)
Page 4
3 RCA to 15-pin D-sub
adapter (g1)
Page 9
• Operation manual (This publication)
Stand unit (g1)
Page 3
Attaching the stand
Before attaching (or detaching) stand, unplug the AC cord from the AC INPUT terminal.
1
Confirm the 8 screws supplied with the TV.
Short screws (m4)
(used in step 2)
Long screws (m4)
(used in step 3)
2
Attach the two parts of the stand unit to each other
using the 4 short screws as shown.
using the 4 short screws as shown.
3
1 Insert the stand into the opening on the bottom
of the TV.
2 Insert and tighten the 4 long screws on the
rear of the TV as shown.
NOTE
• To detach the stand, perform the above steps in reverse
order.
Before performing work spread cushioning over the base area to lay the TV on, making sure the area is
completely flat. This will prevent it from being damaged.
completely flat. This will prevent it from being damaged.
(For Europe, except
U.K. and Eire)
(For U.K. and Eire)
LC-32RD2E_GB_a
07.2.1, 5:13 AM
3
4
Quick guide
Setting the TV
Bundling the cables
Setting the TV on the wall
• This TV should be mounted on the wall only with the wall mount bracket available from SHARP. (See page 35.) The
use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
• When you use the AN-37AG2 (SHARP) wall mount bracket, set the angle of the TV to 0° or 5°. Do not set the angle
to more than 10°.
• Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting
or mounting that results in accident or injury.
or mounting that results in accident or injury.
• You can ask a qualified service personnel about using an optional bracket to mount the TV to the wall.
Standard DIN45325 plug
(IEC 169-2)
75-ohm coaxial cable
(IEC 169-2)
75-ohm coaxial cable
Antenna
Connect the antenna cable from your antenna-/cable
socket or the (room-/roof) antenna for antenna input
terminal on the back of your TV set to receive digitally/
terrestrially broadcast stations.
socket or the (room-/roof) antenna for antenna input
terminal on the back of your TV set to receive digitally/
terrestrially broadcast stations.
An indoor antenna can also be used under good
reception conditions. Passive and active room
antennas are offered commercially. In an active
antenna its power is supplied via the antenna input
terminal.
reception conditions. Passive and active room
antennas are offered commercially. In an active
antenna its power is supplied via the antenna input
terminal.
The supply voltage (5V) must be correspondingly set
under “Supply Voltage”. (See page 18.)
under “Supply Voltage”. (See page 18.)
Ferrite Core
The Ferrite Core should be permanently attached and
never removed from the AC cord.
never removed from the AC cord.
(For Europe, except
U.K. and Eire)
U.K. and Eire)
(For U.K. and Eire)
AC cord
Cable clamp (small)
Cable tie
Ferrite Core
Bundle the AC cord
with the clamp
(small).
with the clamp
(small).
Cable clamp (large)
Bundle the cables
with the clamp
(large).
Before making any
connections, press
down on the upper
hooks and remove the
rear terminal cover
towards you.
connections, press
down on the upper
hooks and remove the
rear terminal cover
towards you.
Place the TV close
to the AC outlet, and
keep the power plug
within reach.
to the AC outlet, and
keep the power plug
within reach.
LC-32RD2E_GB_a
07.2.1, 5:13 AM
4
5
Quick guide
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any
chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
30
°
30
°
Remote control sensor
5 m
1
Hold in the tab on the battery cover (1) and pull
the cover towards the direction of the arrow (2).
the cover towards the direction of the arrow (2).
2
Insert two supplied “AAA” size batteries.
• Place batteries with their terminals corresponding
to the (e) and (f) indications in the battery
compartment.
compartment.
3
Insert the smaller tab of the battery cover into the
opening (1), and press down on the cover until
it clicks in place (2).
opening (1), and press down on the cover until
it clicks in place (2).
Inserting the batteries
Before using the TV for the first time, insert two “AAA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote
control unit and sensor may prevent proper operation.
control unit and sensor may prevent proper operation.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
place in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight. The
heat may cause deformation of the unit.
• The remote control unit may not work properly if the remote control sensor
of the TV is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.
LC-32RD2E_GB_a
07.2.1, 5:13 AM
5
6
Remote control unit
Quick guide
1
17
18
18
19
20
21
22
23
23
24
25
26
27
25
26
27
29
28
30
31
32
33
4
5
15
16
6
7
7
8
9
9
10
11
11
12
13
14
3
2
1
m (Teletext)
Select the TELETEXT mode. (All TV
image, DTV/DATA image, all TEXT
image, TV/TEXT image) (See pages 21
and 31.)
DTV: Select DTV data broadcasting and
TELETEXT.
Select the TELETEXT mode. (All TV
image, DTV/DATA image, all TEXT
image, TV/TEXT image) (See pages 21
and 31.)
DTV: Select DTV data broadcasting and
TELETEXT.
2
B (Standby/On)
Enter standby mode or turn on the
power. (See page 8.)
Enter standby mode or turn on the
power. (See page 8.)
3
3 (Freeze/Hold)
(See page 21.)
(See page 21.)
4
1 (Subpage)
(See page 21.)
(See page 21.)
5
A (Flashback)
Press to return to the previous image
in normal viewing mode. (Will not work
while operating in EPG/ESG screen.)
Press to return to the previous image
in normal viewing mode. (Will not work
while operating in EPG/ESG screen.)
6
EPG
DTV: To display EPG (Electronic
Programme Guide) screen.
DTV: To display EPG (Electronic
Programme Guide) screen.
7
DTV
Press to access DTV mode while
watching other input sources, and vice
versa.
(This button will not work if you were
watching DTV immediately before
turning off the TV. In this case first select
any other input source except DTV
using the b button.)
Press to access DTV mode while
watching other input sources, and vice
versa.
(This button will not work if you were
watching DTV immediately before
turning off the TV. In this case first select
any other input source except DTV
using the b button.)
8
2 (Sound mode)
Select the sound multiplex mode.
(See below.)
Select the sound multiplex mode.
(See below.)
9
i (k/l) (Volume)
i (k) Increase the volume.
i (l) Decrease the volume.
i (k) Increase the volume.
i (l) Decrease the volume.
10
e (Mute)
Switch the sound on and off.
Switch the sound on and off.
11
LIST
DTV: Display the programme list.
DTV: Display the programme list.
12
DTV MENU
DTV: Display DTV Menu screen.
DTV: Display DTV Menu screen.
13
a/b/c/d (Cursor)
Select a desired item on the setting
screen.
Select a desired item on the setting
screen.
14
END
Exit the menu screen.
Exit the menu screen.
15
DEMO
Demonstrate the 100Hz (truD
Demonstrate the 100Hz (truD
®
) effects
in a dual screen format. (See page 14.)
16
SLEEP
Set the sleep timer on (in units of 30
min. up to max. 2 hr. 30 min) and off.
Set the sleep timer on (in units of 30
min. up to max. 2 hr. 30 min) and off.
17
k (Reveal hidden Teletext)
(See page 21.)
(See page 21.)
18
[ (Subtitle for Teletext)
TV/External: To turn the subtitles on and
off. (See page 21.)
DTV: Display the subtitle selection
screen. (See page 31.)
TV/External: To turn the subtitles on and
off. (See page 21.)
DTV: Display the subtitle selection
screen. (See page 31.)
19
v (Top/Bottom/Full)
Set the area of magnification in Teletext
mode. (See page 21.)
Set the area of magnification in Teletext
mode. (See page 21.)
20
0–9
Set the channel in TV and DTV mode.
Set the page in Teletext mode.
Set the channel in TV and DTV mode.
Set the page in Teletext mode.
21
b (INPUT SOURCE)
Select an input source.
(TV, DTV, EXT1, EXT2, EXT3, EXT4,
EXT5, EXT6) (See page 9.)
Select an input source.
(TV, DTV, EXT1, EXT2, EXT3, EXT4,
EXT5, EXT6) (See page 9.)
22
ESG
DTV: To display ESG (Electronic Service
Guide) screen. (See page 30.)
DTV: To display ESG (Electronic Service
Guide) screen. (See page 30.)
23
RADIO
DTV: Switch between RADIO and DTV
mode.
DTV: Switch between RADIO and DTV
mode.
24
AV MODE
Select a video setting. (See page 13.)
Select a video setting. (See page 13.)
25
P (r/s)
TV/DTV: Select the channel.
External: Switch to TV or DTV input
mode.
Teletext: Move to the next/previous
page.
TV/DTV: Select the channel.
External: Switch to TV or DTV input
mode.
Teletext: Move to the next/previous
page.
26
SURROUND
Switch the surround effects on and off.
(See page 15.)
Switch the surround effects on and off.
(See page 15.)
27
p (Display information)
(See pages 21, 29 and 30.)
(See pages 21, 29 and 30.)
28
MENU
Display the MENU screen.
(See page 11.)
Display the MENU screen.
(See page 11.)
29
OK
Execute a command within the menu
screen.
Display the programme list. (Except
external input.)
Execute a command within the menu
screen.
Display the programme list. (Except
external input.)
30
RETURN
Return to the previous menu screen.
Return to the previous menu screen.
31
Colour (Red/Green/Yellow/Blue)
TELETEXT: Select a page. (See page
21.)
DTV: The coloured buttons are used to
select correspondingly to the coloured
items in the menu screen.
TELETEXT: Select a page. (See page
21.)
DTV: The coloured buttons are used to
select correspondingly to the coloured
items in the menu screen.
32
OPC
To switch the Optical Picture Control on
and off. (See page 13.)
To switch the Optical Picture Control on
and off. (See page 13.)
33
f (WIDE MODE)
Select the wide mode. (See page 20.)
Select the wide mode. (See page 20.)
Selectable items
NICAM STEREO, MONO
NICAM CH A, NICAM CH B,
NICAM CH AB, MONO
NICAM CH AB, MONO
NICAM MONO, MONO
Signal
Stereo
Bilingual
Monaural
Selectable items
STEREO, MONO
CH A, CH B, CH AB
MONO
Signal
Stereo
Bilingual
Monaural
NOTE
• When no signal is input, the sound mode will display “MONO”.
NICAM TV broadcasts selection
A2 TV broadcasts selection
E
Using 2 on the remote control unit
DTV mode:
Press 2 to open the multi audio screen. (See page 31.)
Press 2 to open the multi audio screen. (See page 31.)
Analogue TV mode:
Each time you press 2, the mode switches as illustrated in the following tables.
Each time you press 2, the mode switches as illustrated in the following tables.
LC-32RD2E_GB_a
07.2.1, 11:08 AM
6
Click on the first or last page to see other LC-37RD2E (serv.man11) service manuals if exist.