Sharp LC-37GE1E (serv.man6) Service Manual ▷ View online
LC-37GE1E
6 – 5
13.Select the file which you want to upload.
14.Click "Flash" button and get executed.
15.If the Flash has burned successfully, "OK" message is shown as
below.
16.Turn the AC power off , and turn AC power on.
Return to default automatically.
17.Finish!!
18.Prepare for next model
If you have once write the software to the set, the PC side commu-
nication speed will be set up to "115200".
nication speed will be set up to "115200".
So before you connect the PC to the next set, please change back
this speed to "9600".
this speed to "9600".
(Please refer 4-(i)-2)
19.Software writing time
It takes about 15 minutes to write the all software with above
method.
method.
Please keep the cable connection during the PC and Set having a
communication.
communication.
click once
click once
LC-37GE1E
6 – 6
3. Entering and exiting the adjustment process mode
1. Press the “POWER” key on the set of running TV set to force off the power.
2. While holding down the “VOL(-)” and “MENU” keys on the set at once, press the “POWER” key on the set to turn on the power. The letter
appears on the screen.
3. Next, hold down the “VOL(-)” and “P(
)” keys on the set at once. Multiple lines of orange characters appearing on the screen indicate that the
set is now in the adjustment Process mode. If you fail to enter the adjustment process mode (the display is the same as normal startup), retry the
procedure.
procedure.
4. To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the power. (When the power is turned off
with the remote controller, once unplug the AC power cord and plug it in again. In this case, wait 10 seconds or so before plugging.)
5. To remove "K" mode, just repeat steps 1 and 2. This time the letter "K" disappears from screen.
CAUTION: Use due care in handling the information described here lest the users should know how to enter the adjustment process mode. If the set-
tings are tampered with in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode.
1. Key operation
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2. Description of display
Remote controller key
Main unit key
Function
P(
/
)
—————
Changing a selected line setting (+10/-10)
VOL ( + / - )
VOL ( + / - )
Turning a page (PREVIOUS/NEXT)
Cursor (UP/DOWN)
—————
Moving an item (line) by one (UP/DOWN)
Cursor (LEFT/RIGHT)
—————
Turning a page (PREVIOUS/NEXT)
Changing a selected item setting (+1/-1)
Changing a selected item setting (+1/-1)
—————
MENU
Direct control on TV set
(Input/Wide Mode/Bright/Contrast)(Not Operative)
(Input/Wide Mode/Bright/Contrast)(Not Operative)
INPUT SOURCE
on remote controller
on remote controller
—————
Input source switching (toggle switching)
(TV
(TV
→EXT1→EXT2→EXT3→EXT4)(Not Operative)
RETURN
—————
Returning to a present page
OK
—————
Executing a function
K
(1) Current page title
(3) Current page item
[INIT]
[PAL+TUNERMAIN] [COMP] [SCART RGB] [TUNER]
37GE1E ver1.XX XXXX.XX.XX
Dev Version
Center Acutime
Backlight Acutime
XX
Temp Sensor
[2]
[3]
[4]
[5]
Error Standby Cause
[1]
XX
XX
XX
Normal Standby Cause
XX
Main Version
XX
Dev Loader Version
XX
(2) Parameters
LC-37GE1E
6 – 7
5. Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page Line
Item
Description
Remarks (adjustment detail,etc.)
1/12
[INFO]
1
Main Version
37GE1E ver1.10 2006.0715
Main microprocessor version
2
Dev Version
ver1.07
DTV version.
3
Dev Loader Version
2.3
DTV Loader Version
4
Center Acutime
xxxxH xxM
Main operating hours
5
Backlight Acutime
xxxxH xxM
Backlight operating hours
6
Temp Sensor
091
Temp Sensor setting
7
Normal Standby Cause
1 RC_STANDBY
8
Error Standby Cause [1]
[1] 1d FAN ERROR 00H 00M
Error standby cause Total operating time before error
[2]
[2] 1d FAN ERROR 00H 00M
[3]
[3] 1d FAN ERROR 00H 00M
[4]
[4] 1d FAN ERROR 00H 00M
[5]
[5] 1d FAN ERROR 00H 00M
2/12
[INIT]
1
FACTORY INIT
[EURO]ENTER
Initialization to factory settings execution
2
PUBLIC MODE
off/on
HOTEL MODE flag setting
3
Center Acutime Reset
off/on
Main operating hours Reset
4
Backlight Acutime Reset
off/on
Backlight operating hours Reset
5
Picture Read Pos X
626
x-axis setting of picture data
6
Picture Read Pos Y
419
y-axis setting of picture data
7
Picture Read Signal Type
PAL/COMP/HDMI/RGB
no used
8
Picture Read
(0 - 1023)
Start/stop of picture data
3/12
[PAL+TUNERMAIN]
1
RF-AGC BG ADJ
ENTER
RF-AGC BG adjustment execution
2
RF-AGC L ADJ
ENTER
RF-AGC L adjustment execution
3
PAL+TUNER ADJ
ENTER
PAL TUNER auto adjustment execution
4
PAL ADJ
ENTER
PAL auto adjustment execution
5
TUNER ADJ
ENTER
TUNER auto adjustment execution
6
PAL DAC
29
PAL DAC adjustment
7
Tuner A DAC
32
Tuner DAC adjustment
8
Tuner AGC BG
0
Tuner AGC BG adjustment
9
Tuner AGC L
0
Tuner AGC L adjustment
10
Tuner AGC int. offL
6
Tuner AGC gain adjustment
4/12
[COMP 15K]
1
COMP ALL ADJ
ENTER
COMP15K auto adjustment execution
2
COMP CONTRAST
50
COMP contrast adjustment execution
3
COMP Cb GAIN
32
COMP Cb gain adjustment execution
4
COMP Cr GAIN
32
COMP Cr gain adjustment execution
5
COMP BRIGHT
0
COMP bright adjustment execution
5/12
[SCART RGB]
1
SCART RGB ALL ADJ
ENTER
SCART RGB auto adjustment execution
2
SCART RGB CONTRAST
42
SCART RGB contrast adjustment execution
3
SCART RGB Cb GAIN
42
SCART RGB Cb gain adjustment execution
4
SCART RGB Cr GAIN
42
SCART RGB Cr gain adjustment execution
5
SCART RGB BRIGHT
0
SCART RGB bright adjustment execution
6/12
[TUNER]
1
TUNER TEST
7/12
[M GAMMA INFO]
1
M GAMMA POS 1
4
W/B adjustment, gradation 1 input setting
2
M GAMMA POS 2
9
W/B adjustment, gradation 2 input setting
3
M GAMMA POS 3
14
W/B adjustment, gradation 3 input setting
4
M GAMMA POS 4
19
W/B adjustment, gradation 4 input setting
5
M GAMMA POS 5
24
W/B adjustment, gradation 5 input setting
6
M GAMMA POS 6
29
W/B adjustment, gradation 6 input setting
7
M GAMMA WRITE
off/on
EEP writing of adjustment values
8
M GAMMA RESET
off/on
Initialization of adjustment values
LC-37GE1E
6 – 8
8/12
[M GAMMA 1-3]
1
M GAMMA R 1
106
W/B adjustment, gradation 1R adjustment value
2
M GAMMA G 1
106
W/B adjustment, gradation 1G adjustment value
3
M GAMMA B 1
106
W/B adjustment, gradation 1B adjustment value
4
M GAMMA R 2
271
W/B adjustment, gradation 2R adjustment value
5
M GAMMA G 2
271
W/B adjustment, gradation 2G adjustment value
6
M GAMMA B 2
271
W/B adjustment, gradation 2B adjustment value
7
M GAMMA R 3
448
W/B adjustment, gradation 3R adjustment value
8
M GAMMA G 3
448
W/B adjustment, gradation 3G adjustment value
9
M GAMMA B 3
448
W/B adjustment, gradation 3B adjustment value
10
M GAMMA WRITE
off/on
EEP writing of adjustment values
9/12
[M GAMMA 4-6]
1
M GAMMA R 4
623
W/B adjustment, gradation 4R adjustment value
2
M GAMMA G 4
623
W/B adjustment, gradation 4G adjustmnet value
3
M GAMMA B 4
623
W/B adjustment, gradation 4B adjustment value
4
M GAMMA R 5
800
W/B adjustment, gradation 5R adjustment value
5
M GAMMA G 5
800
W/B adjustment, gradation 5G adjustment value
6
M GAMMA B 5
800
W/B adjustment, gradation 5B adjustment value
7
M GAMMA R 6
958
W/B adjustment, gradation 6R adjustment value
8
M GAMMA G 6
958
W/B adjustment, gradation 6G adjustment value
9
M GAMMA B 6
958
W/B adjustment, gradation 6B adjustment value
10
M GAMMA WRITE
off/on
EEP writing of adjustment values
10/12
[ETC]
1
EEP CLEAR
off/on
Clear of process adjustment EEP value
2
EEP CLEAR B
off/on
Clear of process adjustment value of B_mode.
3
STANDBYCAUSE RESET
off/on
Reset of STANDBY CAUSE
4
AUTO INSTALLATION SW
0/1
1:* * * 0: * * *
5
OPTION
0
6
COUNTRY
AUTO/EURO/UK
Destination setting
7
L ERR RESET
0
LAMP ERR RESET Initialization of L_ERR
8
L ERR STOP
0/1
LAMP ERR Inhibit L_ERR detection.
9
DTV CLR
off/on
Clear of DTV unit.
10
I2C-OFF
off/on
STOP of I2C DATA execution
11/12
[LCD]
1
OSC FREQ50
1094
INVERTER drive frequency setting
2
OSC FREQ60
1094
INVERTER drive frequency setting
3
PWM FREQ50
423
Frequency setting for INVERTER dimmer
4
PWM FREQ60
423
Frequency setting for INVERTER dimmer
5
VCOM ADJ
64
12/12
[LCD TESTPATTERN]
1
PATTERN
0
Display LCD test pattern.
Click on the first or last page to see other LC-37GE1E (serv.man6) service manuals if exist.