DOWNLOAD Sharp LC-37GD1E (serv.man7) Service Manual ↓ Size: 50.81 KB | Pages: 7 in PDF or view online for FREE

The adjustment values are set to the optimum conditions at the factory before shipping.  If a value should become
improper or an adjustment is required due to part replacement, make an adjustment according to the following
procedure.

(On The Display)

1. Preparation

When replacing the E2PROM IC (IC2002, IC2008, IC2208), please note that it must be replaced by a unit.
Applicable unit: DUNTKC268VJ18 / DKEYHC269VJ20 (LC-32GD1E)

DUNTKC268VJ17 / DKEYHC269VJ19 (LC-37GD1E)

2. Adjusting procedure

Entering the adjustment process mode 

→

 COM BIAS adjustment 

→

 White balance adjustment (described in the

AVC section)

3. Entering the adjustment process mode

• Connect the AVC and the display using a system cable.
• Turn OFF the display main power (    ).
• While the main power to the display is off, hold down the “P(

Ù

)” key and “        (+)” key on the upper

part of the display and then turn the “MAIN POWER” switch “ON”.  The display will run in the “Display
process mode”.

(“<K>” is displayed in the upper left portion of the screen.)
• Then, pressing any key (

, P or INPUT) will bring you to the first page of the “Display Adjustment mode”.

Multiple lines of red characters appearing on the display indicate that the unit is now in the adjustment process
mode.

4. Exiting the adjustment process mode

• To exit the adjustment process mode after the adjustment is done, unplug the AC power cable from the outlet to
make a forced shutdown.  Do not use the remote controller or the MAIN POWER switch to exit the mode.
(When the power was turned off with the remote controller, once unplug the power cable and plug it again.  In this
case, wait 10 seconds or so before plugging.)

Key
Cursor UP  

'

Cursor DOWN

                    

"

Cursor RIGHT

           û

Cursor LEFT

           Û

  OK

INPUT
P_UP   

     P(

ù

)

P_DOWN  

P(

Ù

)

VOL_UP          (+)

VOL_DOWN

                         (–)

Function 1 (when on the left side of a page)
Moving up by one item or moving to the
previous page (when at the top)
Moving down by one item or moving to the next
page (when at the bottom)
Moving to the right by one item or moving to
another page (in the case of the initial page)
Moving to the left by one item or moving to
another page (in the case of the initial page)
Test pattern off

Moving to the next page
Moving up by one item or moving to the
previous page (when at the top)
Moving down by one item or moving to the next
page (when at the bottom)
Moving to the right by one item or moving to
another page (in the case of the initial page)
Moving to the left by one item or moving to
another page (in the case of the initial page)

Function 2 (when changing a numeric value)
Incrementing the adjustment value by one or
executing the item (in the case of W or R items)
Decrementing the adjustment value by one or
executing the item (in the case of W or R items)
Moving to the right by one item

Moving to the left by one item

Executing the item (in the case of W or R items)

Moving to the next page
Incrementing the adjustment value by one or
executing the item (in the case of W or R items)
Decrementing the adjustment value by one or
executing the item (in the case of W or R items)
Moving to the right by one item

Moving to the left by one item

5. Adjustment process mode key operation table

→

6. Adjustment
6-1. COM BIAS adjustment

Shift to the “COM BIAS” item with the cursor 

'

/

"

key and select a numeric value with the cursor 

Û

/

û

 key.

Changing the numeric value with the cursor 

'

/

"

 key will make appear the test pattern.  Make an adjustment

so that the flicker near the center of the screen is minimized.
Adjust each of the ones, tens and hundreds places so that the flicker is minimized.

6-2. White balance adjustment

The way to enter the adjustment process mode is different.  Please refer to the description given for the AVC
system.
1. Connect the AVC system, start the unit, and then perform a white balance adjustment on the display.
2. Using the cursor 

'

/

" 

key, go to the process adjustment mode page 11 and bring up the adjustment

display  (High side:200 gradations, Low side:48 gradations).

3. Adjust [R GAMMAHI], [G GAMMAHI] and [B GAMMAHI] so that 200-gradation pattern becomes normal.
4. Adjust [R GAMMALO], [G GAMMALO] and [B GAMMALO] so that 48-gradation pattern becomes nomal.

Nomal pattern should be in accordance with the patten of the standard monitor.

Reference: x=0.272, y=0.275 [Minolta CA-210] (200 gradations)

x=0.272, y=0.275 [Minolta CA-210] (48 gradations)

7.Software Upgrade for Monitor Microcomputer

For this model, the software version of the monitor microcomputer can be upgraded via the AVC system. An
SD card is used to upgrade the version. For details of the procedure, method etc., refer to the Service Manual
for TU-32/37GD1E. (AVC SYSTEM)

table of contents of process mode page 0

Adjust each of the ones, tens and 
hundreds places so that the flicker 
is minimized.

SERVICE      S

→

GRAYLEVEL

   COMBIAS
   VLSBIAS
   L ERR RESET
   LCD
   PATTERN
   MOTOR AND FAN
   OTHER
   VER M301

32/37GD1E
100
155
041
    0

CEEPD

8.Lamp error detection
8-1.Feature description

This liquid-crystal colour TV incorporates a lamp error detection feature (lamp error detection) that automatically
turns OFF the power for safety under abnormal lamp or lamp circuit conditions.
If anything is wrong with the lamp or lamp circuit or when the lamp error detection feature is activated for some
reason, the following will result.

1

The power of TV main body is turned OFF about six seconds after it is turned ON.  (The power LED on
the front of the TV turns red from green and keeps blinking in red (ON for 250ms and OFF for 1sec).)

2

If 

1

 occurs five times consecutively, it becomes impossible to turn ON the power.  (The power LED

keeps blinking in red (ON for 250ms and OFF for 1sec).)

8-2.Measures

1).Checking with lamp error detection OFF

While the “MAIN POWER” switch is off, hold down the “P(

Ù

)” and “       (+)” keys and then turn the “MAIN

POWER” on. The display will run in the “Display process mode” (“<K>” will appear.).

      If there is a problem with a lamp or a lamp circuit, the lamp will go out. (The power LED is green.)
      Then, you can check the operation to see if the lamp and lamp circuit are abnormal.

2).Resetting the lamp error count

After you have finished checking whether the lamp and lamp circuit are abnormal, reset the lamp error
count. If a lamp error is detected five consecutive times, the power cannot be turned on.

      Therefore, move to the “L ERR RESET” line, the fourth line on the first page of the“Display adjustment
      mode”, using the “Cursor 

'

/

"

” key. Then, reset the “L ERR RESET” value using the “Cursor 

Û 

/ 

û

” key.

      In this case, press the “Cursor 

'

/

"

” key to reset it to "0".

Then perform operation checking and check that the lamp error detection feature is not activated.

table of contents of process mode page 0

Normal values of individual displays

Reset to "0"

SERVICE      S
   GRAYLEVEL
   COMBIAS
   VLSBIAS
   L ERR RESET
   LCD
   PATTERN
   MOTOR AND FAN
   OTHER
   VER M301

32/37GD1E
100
155
041
    0

CEEPD

Table of contents of process mode  Page 0

LCD  Page 5

LCD  Page 6

SERVICE  S 

            32/37GD1E 

→ＧＲＡＹＬＥＶＥＬ 

 1  0  0  

    ＣＯＭＢＩＡＳ  

 1  5  5 

 ＶＬＳＢＩＡＳ  

 0  4  1 

 Ｌ ＥＲＲ ＲＥＳＥＴ 

        ０ 

 ＬＣＤ 
 ＰＡＴＴＥＲＮ 
 M O T O R ＡＮＤ ＦＡＮ 
 ＯＴＨＥＲ 
  ＶＥＲ Ｍ301 ＣＥＥＰ D

ＬＣＤ6 
→V  H    ０  

0 1 5 8 

 V  L    ０  

0 9 3 8 

 V  H  3 1  

0 4 1 8 

 V  L  3 1  

0 6 8 6 

 V  H  6 3  

0 4 5 2 

 V  L  6 3  

0 6 1 9 

 V  H  9 5  

0 5 0 3 

 V  L  9 5  

0 5 9 0  

ＬＣＤ6 
→V  H 1 2 7  

 0 5 2 1 

 V  L  1 2 7   

 0 5 4 2 

 V  H 1 5 9  

 0 5 6 8 

 V  L  1 5 9  

 0 4 9 7 

 V  H 1 9 1  

 0 6 1 8 

 V  L  1 9 1  

 0 4 4 5 

 V  H 2 4 7  

 0 9 1 4 

 V  L  2 4 7  

 0 1 3 3  

LCD  Page 1

LCD  Page 2

LCD  Page 3

ＬＣＤ3 
→ＯＰＣ ０           

   0 0  

    ＯＰＣ １  

  ０5 

 ＯＰＣ ２  

  ０9 

 ＯＰＣ ３  

   1 3 

 ＯＰＣ ４  

   1 8 

 ＯＰＣ ５  

   2 2 

 ＯＰＣ ６  

   2 7 

 ＯＰＣ ７  

   3 1 

 ＯＰＣ ８  

   3 6

ＬＣＤ2 
→ＭＯＤＥ       PC 

   ０ 

 QＳ ＳＷ        

     ０ 

 QＳ Ｄ１      

0 8 2  

    QＳ Ｄ２      

1 0 0 

 QＳ Ｄ３      

1 1 1 

 QＳ Ｄ４      

1 2 3 

 QＳ Ｄ５      

1 3 5 

 QＳ Ｄ６      

1 4 7 

 QＳ Ｄ７      

1 6 2

ＬＣＤ1 
→ＭＯＤＥ          PC          ０ 
 ＰＷＭＣＴＲＬ   

         7 

 ＰＷＭＦＲＥＱ          1  2  8  9 
 ＰＷＭＤＵＴＹ 1            ００００ 
    ＰＷＭＤＵＴＹ 2            ００００ 
 ＰＨＡＳＥＤＩＦ  

０００ 

 ＰＣＬＫ１     

   0 

 ＰＣＬＫ２     

   0

LCD  Page 4

ＬＣＤ4 
→ＯＰＣ  ９   

    4 ０ 

 ＯＰＣ １０   

    4  5 

 ＯＰＣ １１  

    4  9 

 ＯＰＣ １２  

    5  3 

 ＯＰＣ １３  

    5  8 

 ＯＰＣ １４  

    6  2 

 ＯＰＣ １５  

    6  7 

 ＯＰＣ １６  

    7  1  

•

List of process adjustment modes