DOWNLOAD Sharp LC-37GA5E (serv.man5) Service Manual ↓ Size: 1.7 MB | Pages: 12 in PDF or view online for FREE

Hardware requirements
To update VCT it is needed:
1. A converter from Parallel port to DB9 supplied by Micronas, a male DB9  to  female DB9 wire and the updating
    tool (Part Code: CKIT-0002WJV0).
2. Make the connections as indicated below.

2.1. Connect Parallel cable from the updating tool to the PC.
2.2. Connect the long cable from the updating tool to the P2005 connector (LCD Controller PWB).

Software requirements
A complete Visual I2C (VI2C) installation consists of 4 software components:

1. Visual I2C main program (‘visuali2c.exe’ and several DLL files)
2. Several DALs: These are IC specific low-level access drivers for the I2C bus.
3. A Windows port driver (LPT or USB). There are three versions for Win9x and WinNT/2000/XP.
4. One or more applications (‘*.vi2c’). They’re representing the interface to the user.

Access to folder:
-

D:\SOFTWARE UPDATE GA5\Installation order VCTi\1

-

Install Visual I2C (SETUP_VISUAL_I2C_V3_1_7C.EXE)

It’s strongly recommended to accept the suggested default folder.

Access to folder:
-

D:\SOFTWARE UPDATE GA5\Installation order VCTi\2

-

Install LPT driver SETUP_LPTDRVDEV_V0202_XP_20.EXE

Use for Windows 95/98:       Setup_LptDrv_v0104_9x.exe
Use for Windows 2000/XP:   Setup_LptDrv_v0202_XP_20.exe
Use for Windows NT:           Setup_LptDrv_v0104_NT.exe

After installing VI2C, the new generated file structure should look like this:
—> Micronas
        |—> LptDrv   (in case of parallel port driver installed!)
        |—> Visual I2C
               |—> dal
               |—> doc
               |—> Port_Driver
-

Check installation of LPT driver:

C:\Program Files\Micronas\LptDrv\LptDrvTest.exe

If the LPT Driver is OK, the next picture shows:

If this test is not OK, check in your BIOS: Parallel Port Mode = EPP

How to use the application
-To start VCTi software updater program, you can create direct access to:
 C:\Program Files\Micronas\Visual I2C\VCT49xyi\vcth_tvt_16bit.vi2c
-Run direct access «vcth_tvt_16bit.vi2c».

Access to folder:
-D:\SOFTWARE UPDATE GA5\Installation order VCTi\VCT49xyi
-Copy all the content to the folder C:\Program Files\Micronas\Visual I2C and after selecting all files and directories
and change the «Read only» property. (When you copy from CD, the files are read only protected)

Check your installation:
-When you finish this process the Visual I2C is ready for Win2000 and XP
-LptDriver V.2.2.0 and VctiDown.exe V 1.3  are installed.

-If you have Win98 is necessary change version VctiDown.exe.
-Extract C:\Program Files\Micronas\Visual I2C\VCT49xyi\download\VctiDown_v1-2.zip in the same folder.
-Check LptDriver V1.4.0 and VctiDown.exe V1.2 are installed (Win98).

- Double click the file name in the Load Bin field and select the software version file.
- The first time you do this process confirm that the field address is from 0x800000 to 0x8FFFFF.

\

S

-Press OK and Error disappear. Now the program is available for use.

- Select Bootloader option. Set AutoRead to ON and wait until 21 appears in Bootlader Version field.
- Click on the button Erase 16bit Flash. The bootloader version will be zero during few seconds. When the
  version field marks again 21 set Auto Read OFF.
- Click on the button LOAD BIN -> FLASH and the updating will start up.
- The updating will end before the progress bar reaches the end; if there is no error message the updating has
  been good.

Sometime the progress bar is very quick or error message appears, then is necessary increase the delay until
the problem disappear:

-Select LPT Preference.

 6HOHFW/373UHIHUHQFH

- Increase Delay: normally 2 or 3 are the best choice.

\

\

If there are further problems to enter the bootloader mode you can use the hardware method:

-  Power off VCTi or hold RESET line to GND.
-  Pull down SCL line to GND.
-  Power up VCTi or release RESET line.
-  Release SCL pull down after minimum of 1 second.
-  Check if VCTi is in bootloader mode with a AutoRead.