Sharp LC-32SH7E Service Manual ▷ View online
2008-03-14
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
37
TROUBLESHOOTING TABLE(26“&32”)
Power unit operation check.
↓
LINE_FILTER_UNIT:
↓ YES
POWER_UNIT
↓YES
↓YES
↓YES
↓YES
Are the power cord and harness in the unit properly connected?
NO
Connect the power cord and harness properly, and turn on the
power.
power.
Is F901/F902 normal?
NO
LINE_FILTER_UNIT:
Isn't RV901,L901,C904,L902,C903,C902,RV903, etc. out of
order? Moreover, whether the short-circuit with the
circumference circuit is checked.
POWER_UNIT:
BD901, FB905, C905, etc. out of order?
Moreover, whether the short-circuit with the circumference circuit
is checked.
Isn't RV901,L901,C904,L902,C903,C902,RV903, etc. out of
order? Moreover, whether the short-circuit with the
circumference circuit is checked.
POWER_UNIT:
BD901, FB905, C905, etc. out of order?
Moreover, whether the short-circuit with the circumference circuit
is checked.
Is BD901 (+320V) output? (Set the main power SW to OFF.)
* When power on/off switch is on ‧‧‧ About +400V
* When power on/off switch is on ‧‧‧ About +400V
Does the PFC circuit operate normally?
(L906, Q901, D902, D903, IC901 and etc. And, the circuit around
the protection circuit etc. is checked.)
(L906, Q901, D902, D903, IC901 and etc. And, the circuit around
the protection circuit etc. is checked.)
NO
Is a voltage of +5V applied to pin (12,13) of connector (CN902)?
(Set the main power SW to OFF.)
(Set the main power SW to OFF.)
Does the switching circuit operate normally?
Check circuit around the primary side (T901, IC931, Q931,
ZD931, ZD930, ZD980, ZD981, etc.), the secondary side (D935,
L980, etc.), the AC_DET circuit (IC932, IC982, etc.), and the
protection circuit.
Check circuit around the primary side (T901, IC931, Q931,
ZD931, ZD930, ZD980, ZD981, etc.), the secondary side (D935,
L980, etc.), the AC_DET circuit (IC932, IC982, etc.), and the
protection circuit.
NO
Are +24V output as for the power on/off switch when it is on?
NO
Does the inverter circuit operate normally?
Check circuit around the primary side (T902,Q951,Q952,IC951,
D951,D952, etc.), the secondary side (D955, L932, ZD967,
IC952, IC953, etc.), the STANDBY circuit (Q988, etc.), and the
protection circuit.
Check circuit around the primary side (T902,Q951,Q952,IC951,
D951,D952, etc.), the secondary side (D955, L932, ZD967,
IC952, IC953, etc.), the STANDBY circuit (Q988, etc.), and the
protection circuit.
Similarly, is +12V output as for the power on/off switch when it is
on?
on?
NO
Check +12V circuit of D956, L931, etc.
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
38
The sound is not emitted from the speaker though the picture has come out.
↓
No sound output in all modes?
TEREMINAL UNIT:
↓
↓YES
↓YES
↓YES
↓YES
↓YES
No sound (during the reception of TV(ANALOG) broadcasting)
↓
Does not the sound go out though the picture has come out when UHF/VHF is received?
TEREMINAL UNIT:
↓
↓YES
↓YES
Is the audio signal output of pin (84) (AUOutL) and pin (85)
(AUOutL) of IC U4201 normal?
(AUOutL) of IC U4201 normal?
NO
Check IC U4201 and its peripheral circuits.
Is audio signal input to pin (5)(LIN), pin (6)(RIN) of IC U6102
(AMP)?
(AMP)?
NO
Check the line between IC U6101 and IC U6102.
Is MUTE/SHUTDOWN circuit [AMP_MUTE, AMP_STBY] normal?
Is the audio signal output of pin (3,4) (LOUT+) and pin (1,2)
(ROUT+) of CN6101 (AUDIO-CONNECTOR) normal?
(ROUT+) of CN6101 (AUDIO-CONNECTOR) normal?
NO
Check the AMP_MUTE and AMP_STBY. (Q6106, etc.)
NO
Check IC U6102 and its peripheral circuits.
Check Speaker Box (right and left) and wire harness.
Is the SIF signal output from pin (13) of TUNER (TU1101)?
Is the SIF signal sent to pin 54(SIFP) and pin 55(SIFM) of IC
U4201?
U4201?
NO
Check the tuner and its peripheral circuits. Replace as required.
NO
Check IC U4201 its peripheral circuits.
Refer to “No sound output in all modes”.
Is the audio signal output of pin (9) (OUTL) and pin (11) (OUTR) of
IC U6101 normal?
IC U6101 normal?
NO
Check IC U6101 and its peripheral circuits.
2008-03-14
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
39
No sound from external input devices (1)
↓
Does not the sound of the audio signal input to SCART1 go out?
Does not the sound of the audio signal input to SCART2 go out?
TEREMINAL UNIT:
↓
↓YES
↓YES
↓YES
No sound from external input devices (2)
↓
Does not the sound of the audio signal input to YPbPr (Component) go out?
MAIN UNIT:
↓
↓YES
↓YES
↓YES
Is the audio signal properly sent to pin (6) (YPbPr2_AU_INL) and
pin (2) (YPbPr2_AU_INR) of SCART1(CN1901)?
pin (2) (YPbPr2_AU_INR) of SCART1(CN1901)?
Is the audio signal properly sent to pin (6) (SCHF_AU_INL) and pin
(2) (SCHF_AU_INR) of SCART2(CN1902)?
(2) (SCHF_AU_INR) of SCART2(CN1902)?
Check the setting of an external input device that connects of
CN1901.
CN1901.
NO
Check the setting of an external input device that connects of
CN1902.
CN1902.
NO
Is the audio signal properly sent to pin (1) (NO) and pin (1) (NO) of
IC U1702/U1701?
IC U1702/U1701?
Is the audio signal properly sent to pin (3) (NC) and pin (3) (NC) of
IC U1702/U1701?
IC U1702/U1701?
NO
NO
Check the line between CN1901 and IC U1701/U1702.
Check the line between CN1902 and IC U1701/U1702.
Refer to “No sound output in all modes”.
Is the audio signal properly sent to pin (8) (YPbPr1_AU_INL) and
pin (10)( YPbPr1_AU_INR) of CN1201?
pin (10)( YPbPr1_AU_INR) of CN1201?
NO
Check the connection to CN1201 and the external input device.
Refer to “No sound output in all modes”.
Is the audio signal properly sent to pin (70) (AUL0) and pin (71)
(AUR0) of IC U4201?
(AUR0) of IC U4201?
NO
Check the line between CN1201 and IC U4201.
Is the audio signal properly sent to pin (72) (AUL1) and pin (73)
(AUR1) of IC U4201?
(AUR1) of IC U4201?
Check the line between IC U1701/U1702 and IC U4201.
NO
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
40
No sound from external input devices (3)
↓
Does not the sound of the audio signal input to PC(VGA) go out?
MAIN UNIT:
↓
↓YES
↓YES
↓YES
No sound from external input devices (4)
↓
Does not the sound of the audio signal input to “AV side” go out?
MAIN UNIT:
↓
↓YES
↓YES
↓YES
No sound from external input devices (5)
↓
Does not the sound of the audio signal input to HDMI 1/”HDMI side” go out?
↓
↓YES
Is the audio signal properly sent to pin (2) (PC_AU_INL) and pin (3)
(PC_AU_INR) of CN1703?
(PC_AU_INR) of CN1703?
NO
Check the connection to CN1703 and the external input device.
Refer to “No sound output in all modes”.
Is the audio signal properly sent to pin (75) (AUL2) and pin (76)
(AUR2) of IC U4201?
(AUR2) of IC U4201?
NO
Check the line between CN1703 and IC U4201.
Is the audio signal properly sent to pin (4) (SIDE_AU_INL) and pin
(6) (SIDE_AU_INR) of CN1206?
(6) (SIDE_AU_INR) of CN1206?
NO
Check the connection to CN1206 and the external input device.
Refer to “No sound output in all modes”.
Is the audio signal properly sent to pin (77) (AUL3) and pin (78)
(AUR3) of IC U4201?
(AUR3) of IC U4201?
NO
Check the line between CN1206 and IC U4201.
Refer to “No sound output in all modes”.
Is picture of the signal input from HDMI 1/HDMI side displayed?
NO
Refer to “Does not the picture of the HDMI signal input to
HDMI 1/HDMI side go out?”.
HDMI 1/HDMI side go out?”.
Click on the first or last page to see other LC-32SH7E service manuals if exist.