DOWNLOAD Sharp LC-32SA1E (serv.man4) Service Manual ↓ Size: 1.59 MB | Pages: 28 in PDF or view online for FREE

You can run Auto Installation again, even after setting
up the preset channels.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press a/b to select “Auto Installation”, and then
press OK.
If you have already set the PIN under “Child Lock”,
enter it here.

• See page 16 for setting PIN.

Press c/d to select “Yes”, and then press OK.

You can set language and country the same as in
the initial auto installation. Follow steps 1 and 2
on page 7.

This section describes how to set up analogue TV
channels manually.

MENU    

[Setup]

Setup

Option

Child Lock

Auto Installation

Programme Setup

Position

WSS

4:3 Mode

[Panorama]

[On]

[English]

Language

You can automatically search for and download TV
channels  by performing the procedure below. This is
the same function as from programme auto search to
preset download in Auto Installation.

Repeat steps 1 to 4 in Programme Setup.

Press c/d to select “Yes”, and then press OK.

1 Programme auto search
2 Auto labelling
3 Auto sorting
4 Preset download

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press  a/b to select “Programme Setup”, and
then press OK.
If you have already set the PIN under “Child Lock”,
enter it here.

• See page 16 for setting PIN.

Press  a/b to select “Auto Search”,  “Manual
Adjust”, “Sort” or “Erase Programme”, and then
press OK.

Auto Search

Manual Adjust

Sort

Erase Programme

No

Yes

Menu Operation: A (page 11)
When set to “Enable” the TV will automatically enter
the standby mode if there is no signal input for 15
minutes.

• Five minutes before the TV enters standby mode, the

remaining time displays every minute.

• When a TV programme finishes, this function may not

operate.

MENU    

[Power Control]

Audio

Power Control

No Signal Off

No Operation Off

[Disable]

[Disable]

Menu Operation: A (page 11)
When set to “Enable” the TV will automatically enter
the standby mode if no operations are performed for
3 hours.

• Five minutes before the TV enters standby mode, the

remaining time displays every minute.

When set, the TV will automatically enter the standby
mode.

• No power management
• Factory preset value.

Mode1: • If there is no signal input for 8 minutes, the TV

enters the standby mode.

• Even if you start using the PC and the signal

inputs again, the TV stays in standby mode.

• The TV turns on again by pressing a on the TV

or B on the remote control unit. (See page 7.)

Mode2: • If there is no signal input for 8 seconds, the

TV enters the standby mode.

• When you start using the PC and the signal

inputs again, the TV turns on.

• The TV turns on again by pressing a on the TV

or B on the remote control unit. (See page 7.)

LC-32SA1E_GB_b

06.7.25, 11:35 AM

14

You can set some channel items manually.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press  a/b to select “Programme Setup”, and
then press OK.
If you have already set the PIN under “Child Lock”,
enter it here.

• See page 16 for setting PIN.

Press  a/b to select “Manual Adjust” and then
press OK.

Press c/d to select “Yes”, and then press OK.

Press a/b/c/d to select the channel you want
to edit, and then press OK.

• The selected channel information displays.

Press a/b to select the desired menu item, and
then press OK.

Press a/b/c/d to select or adjust.

MENU    

[Setup ... Programme Setup]

Fine

Colour sys.

Sound sys.

Label

Skip

Decoder

Lock

[179.25]

[AUTO]

[B/G]

[Off]

[SAT.1]

[Off]

[Off]

179.25

MHz

• When you exit Programme Setup “Manual Adjust” menu,

preset download automatically runs if you change
information on that menu.

You can adjust the frequency to your desired position.

• Adjust while checking the background picture as a

reference.

• Instead of pressing c/d to adjust the frequency in step

8 above, you can set by directly entering the frequency
number of the channel with  0–9.

• 179.25 MHz: Press 1 s 7 s 9 s 2 s 5.
• 49.25 MHz: Press 4 s 9 s 2 s 5 s OK.

When a TV channel sends its Network Name, the Auto
Installation detects the information and assigns a name
to it. However, you can change individual channel
names.

Repeat steps 1 to 7 in Manual Adjust.

Channels with “Skip” set to “On” are passed over when
using  Pr/Ps even if selected while watching the
image from the TV.

When connecting a decoder to the unit, you need to
select EXT1.

• “Off” is factory preset value.

You can block the viewing of any channel.

• See page 16 for setting PIN.
• When Lock is set to “On” for a channel, “Child lock has

been activated.” displays, and the image and sound of
the channel are blocked.

• When pressing OK while “Child lock has been activated.”

displays, PIN input menu will display. Inputting the correct
PIN lifts the child lock temporarily until the power is turned
off.

Select the optimum colour systems to receive. (AUTO,
PAL, SECAM)

Select the optimum sound systems (Broadcasting
systems) to receive. (B/G, D/K, I, L, L’)

Channel positions can be sorted freely.

Repeat steps 1 to 4 in Programme Setup.

Press c/d to select “Yes”, and then press OK.

Press a/b/c/d to select the channel you want
to move, and then press OK.

Press  a/b/c/d to move it to the desired
position, and then press OK.

Repeat steps 3 and 4 until all desired channels
are sorted.

An individual programme can be erased.

Repeat steps 1 to 4 in Programme Setup.

Press c/d to select “Yes”, and then press OK.

Press a/b/c/d to select the channel you want
to erase, and then press OK.

• A message screen pops up.

Press c/d to select “Yes”, and then press OK to
erase the selected programme. All the subsequent
programmes move up.

Repeat steps 3 and 4 until all desired channels
are erased.

Press a/b/c/d to select each character of the
new name for the channel, and then press OK.

Repeat step 2 above until the name is fully spelt
out.

• The name can be 5 characters or less.
• If a channel name is less than 5 characters, select

“END”, then press OK.

LC-32SA1E_GB_b

06.7.25, 11:35 AM

15

Allow you to use a PIN to protect certain settings from
being accidentally changed.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press a/b to select “Child Lock”, and then press
OK.

New PIN

–

–

–

Reconfirm

–

–

–

–

–

Change PIN

Reset

Enter the 4-digit number as a PIN using 0 – 9.

Enter the same 4-digit number as in step 4 to
confirm.

• “The system PIN has been changed successfully”

displays.

• To view a locked channel (Lock setting in Programme

Setup “Manual Adjust” is set to “On”), you must enter a
PIN. (See page 15.) When you select a locked channel, a
PIN prompt message pops up. Press OK to display the
PIN input window.

Allow you to reset your PIN to the factory preset “1234”.

Repeat steps 1 to 3 in Changing the PIN.

Enter the PIN.

Press a/b to select “Reset”, and then press OK.

Press c/d to select “Yes”, and then press OK.

• As a precautionary measure, make a note of your PIN

• See page 21 for resetting the current PIN to the factory

You can assign each input source a label you like.

Press b to select the desired input source.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press a/b to select “Input Label”, and then press
OK.

Press a/b/c/d to select each character of the
new name for the input source, and then press
OK.

Repeat step 5 above until the name is fully spelt
out, and then press OK.

• The name can be 6 characters or less.
• If a label name is less than 6 characters, select

“END”, then press OK.

• You cannot change the label if the input source is TV.

Ordinarily, the TV automatically adjusts image positions
coming from PC (Auto Sync. function). In some cases,
however, manual adjustment is needed to optimise the
image.

H-Pos.: Centres the image by moving it to the left or right.
V-Pos.: Centres the image by moving it up or down.
Clock: Adjusts when the image flickers with vertical

stripes.

Phase: Adjusts when characters have low contrast or

when the image flickers.

• If you need to adjust the image position, adjust the position

using your PC.

LC-32SA1E_GB_b

06.7.25, 11:35 AM

16

For adjusting a picture’s horizontal and vertical
position.

• Adjustments are stored separately according to input

• Depending on the input signal type a position setting may

not be available.

H-Pos.: Centres the image by moving it to the left or right.
V-Pos.: Centres the image by moving it up or down.

When listening to music from a music programme, you
can set the TV off and enjoy audio only.

MENU    

[Option]

Option

Audio Only

DNR

Input Select

Colour System

[Off]

[CVBS]

[AUTO]

Demo

You can select a language from the Setup menu. Select
from among 13 languages. (Dutch, English, Finnish,
French, German, Greek, Italian, Polish, Portuguese,
Russian, Spanish, Swedish, Turkish)

• “HDMI Setup” is displayed only when “EXT5” is selected

from the INPUT SOURCE menu.

Off: Both screen images and audio are output.
On: Audio is output without screen image.

WSS allows a television to switch automatically among
the different screen formats.

• Use WIDE MODE if an image does not switch to the correct

screen format. When the broadcast signal contains no
WSS information, the function will not work even if enabled.
(See page 19.)

The WSS signal has 4:3 auto-switching that allows you
to select between Normal and Panorama.

Normal: Normal range keeping 4:3 or 16:9 aspect ratio
Panorama: Wide image without side bars

LC-32SA1E_GB_b

06.7.25, 11:35 AM

17