Sharp LC-32LE700E (serv.man14) User Manual / Operation Manual ▷ View online
5
Supplied accessories
Remote control unit ( x 1)
AC cord ( x 1)
Cable clamp ( x 1)
Stand unit ( x 1)
Product shape varies in
some countries.
For 32 inch models
For 40/46/52 inch models
Pages 3 and 6
Page 8
Page 8
Page 5
Operation manual (this publication)
“AAA” size zinc-carbon battery ( x 2) ... Page 6
“AAA” size zinc-carbon battery ( x 2) ... Page 6
•
•
•
Attaching the stand unit
Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent it from being damaged.
Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent it from being damaged.
CAUTION
Attach the stand in the correct direction.
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
Confirm that there are eight screws with the
stand unit.
stand unit.
Models
Screws
32 inch models
A
B
40/46/52 inch models
C
D
Attach the supporting post for the stand unit
onto the base using the four screws with the
screw driver as shown.
onto the base using the four screws with the
screw driver as shown.
*
Supporting
post
post
32 inch models: Use Screws B in the table in step 1.
40/46/52 inch models: Use Screws D in the table in step 1.
40/46/52 inch models: Use Screws D in the table in step 1.
1
2
*
*
*
Inserting the stand.
Insert the stand into the openings on the
bottom of the TV (hold the stand so it will not
drop from the edge of the base area).
Insert and tighten the four screws into the four
holes on the rear of the TV.
bottom of the TV (hold the stand so it will not
drop from the edge of the base area).
Insert and tighten the four screws into the four
holes on the rear of the TV.
1
1
2
2
Soft cushion
32 inch models: Use Screws A in the table in step 1.
40/46/52 inch models: Use Screws C in the table in step 1.
40/46/52 inch models: Use Screws C in the table in step 1.
NOTE
To detach the stand unit, perform the steps in reverse order.
A screw driver is not supplied with this product.
The stand base is made of glass. Therefore, be careful not to
drop the stand base or apply pressure to it.
Do not place heavy objects on the stand base.
A screw driver is not supplied with this product.
The stand base is made of glass. Therefore, be careful not to
drop the stand base or apply pressure to it.
Do not place heavy objects on the stand base.
3
1
2
*
*
*
•
•
•
•
•
•
•
•
•
•
•
•
Preparation
LC-LE700E_GB.indd 5
LC-LE700E_GB.indd 5
2009/07/13 14:51:21
2009/07/13 14:51:21
6
Inserting the batteries
Before using the TV for the first time, insert two supplied “AAA” size zinc-carbon batteries. When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
Open the battery cover.
Insert two supplied “AAA” size zinc-carbon
batteries.
batteries.
Place batteries with their terminals corresponding to the (
e)
and (
f) indications in the battery compartment.
Close the battery cover.
1
2
2
•
3
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old
batteries.
Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage,
wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
When replacing the batteries, use zinc-carbon batteries instead of alkaline ones.
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old
batteries.
Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage,
wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
When replacing the batteries, use zinc-carbon batteries instead of alkaline ones.
Note on disposing batteries:
The batteries provided contain no harmful materials such as cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household rubbish.
Deposit any used batteries free of charge into the designated collection containers set up at commercial businesses.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household rubbish.
Deposit any used batteries free of charge into the designated collection containers set up at commercial businesses.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control unit
and sensor may prevent proper operation.
and sensor may prevent proper operation.
5 m
Remote control sensor
Cautions regarding the remote control unit
Do not expose the remote control unit to shock. In addition, do not expose the remote
control unit to liquids, and do not place in an area with high humidity.
Do not install or place the remote control unit under direct sunlight. The heat may cause
deformation of the unit.
The remote control unit may not work properly if the remote control sensor of the TV is
under direct sunlight or strong lighting. In such cases, change the angle of the lighting or
the TV, or operate the remote control unit closer to the remote control sensor.
control unit to liquids, and do not place in an area with high humidity.
Do not install or place the remote control unit under direct sunlight. The heat may cause
deformation of the unit.
The remote control unit may not work properly if the remote control sensor of the TV is
under direct sunlight or strong lighting. In such cases, change the angle of the lighting or
the TV, or operate the remote control unit closer to the remote control sensor.
•
•
•
•
•
•
•
•
•
•
•
•
Preparation
LC-LE700E_GB.indd 6
LC-LE700E_GB.indd 6
2009/07/13 14:51:22
2009/07/13 14:51:22
7
Initial installation overview
Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary depending
on your TV installation and connection.
on your TV installation and connection.
Preparation
Connect an antenna cable to the
antenna terminal (Page 8).
antenna terminal (Page 8).
If necessary, insert a CA
card into the CI slot to watch
scrambled broadcasts (Page 11).
card into the CI slot to watch
scrambled broadcasts (Page 11).
Connect the AC cord to the TV
(Page 8).
(Page 8).
Product shape varies in some
countries.
Run the
initial
settings
Turn on (;) the MAIN POWER
switch on the left side of the TV
(Page 4).
switch on the left side of the TV
(Page 4).
Turn on the power using a on
the TV (Page 12).
the TV (Page 12).
Run the initial auto installation
(Page 9).
(Page 9).
Language setting
Home/Store setting
HOME
STORE
Country setting
Austria
Finland
Greece
Channel search
setting
setting
Digital search
Analogue search
Start searching
channels
✔
✔
✔
✔
Watch TV
Congratulations!
Now you can watch TV.
Now you can watch TV.
If necessary, adjust the antenna
to attain maximum signal
reception (Page 11).
to attain maximum signal
reception (Page 11).
Connect external
devices
Connect external devices
such as a DVD player/
recorder as instructed (Pages
16_18).
such as a DVD player/
recorder as instructed (Pages
16_18).
Connect external audio
devices such as speakers/
amplifier as instructed (Page
18).
devices such as speakers/
amplifier as instructed (Page
18).
Quick guide
LC-LE700E_GB.indd 7
LC-LE700E_GB.indd 7
2009/07/13 14:51:23
2009/07/13 14:51:23
8
Before turning on the power
2
*
1
Cable clamp (bundle the cables with the clamp)
Standard DIN45325 plug (IEC 169-2) 75
q coaxial cable
Turn on (;) the MAIN POWER switch on the left side of the TV.
AC cord (product shape varies in some countries)
The AC cord is supplied either with a ferrite core or without a ferrite core. Neither type
causes unnecessary electrical wave emissions or interference.
causes unnecessary electrical wave emissions or interference.
*
Place the TV close to the AC outlet,
and keep the power plug within
reach.
and keep the power plug within
reach.
Supplying power to the antenna
You must supply power to the antenna in order to receive digitally/terrestrially broadcast stations after connecting
the antenna cable to the antenna terminal on the rear of the TV.
the antenna cable to the antenna terminal on the rear of the TV.
Press @ and the “MENU” screen displays.
Press
Press
c/d to select “Setup”.
Press
a/b to select “Antenna setup-DIGITAL”, and then press ;.
Press
a/b to select “Supply voltage”, and then press ;.
Press
c/d to select “On”, and then press ;.
1
2
3
4
5
2
3
4
5
Mounting the TV on a wall
This TV should be mounted on a wall only with the wall mount bracket and attachment* available from SHARP (Page 45).
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
Mounting the LCD colour TV requires special skills and should only be performed by qualified service personnel. Customers
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that
results in accident or injury.
You can ask qualified service personnel about using an optional bracket and attachment* to mount the TV to a wall.
When you mount the TV on a wall, you should attach the supporting post.
Only for 40 inch models.
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
Mounting the LCD colour TV requires special skills and should only be performed by qualified service personnel. Customers
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that
results in accident or injury.
You can ask qualified service personnel about using an optional bracket and attachment* to mount the TV to a wall.
When you mount the TV on a wall, you should attach the supporting post.
Only for 40 inch models.
•
•
•
•
*
•
*
Quick guide
LC-LE700E_GB.indd 8
LC-LE700E_GB.indd 8
2009/07/13 14:51:25
2009/07/13 14:51:25
Click on the first or last page to see other LC-32LE700E (serv.man14) service manuals if exist.