Sharp LC-32LE351K (serv.man2) Service Manual ▷ View online
29
LC-32LE351
LC-39LE351
14
Table 4: Recommended operating conditions
C. HEADPHONE AMPLIFIER STAGE
Headphone is a SoC (single on chip) configuration in mainboard, design scheme is shown
in figure 4.
Figure 4: Headphone
30
LC-39LE351
LC-32LE351
15
4. POWER STAGE
Figure 5: Power socket and power options
Power socket is used for taking voltages which are 3.3V, 12V, 5V and 24V(VDD_Audio).
These voltages are produced in power card. Also socket is used for giving dimming, backlight
and standbye signals with power card. İt is shown in figure 5.
and standbye signals with power card. İt is shown in figure 5.
24V(VDD_Audio) goes directly to the audio side, through power socket other incoming
voltages from power card are converted several voltages.
Figure 6: Power steps
31
LC-32LE351
LC-39LE351
16
FDC642P
General Description and Features
TPS65251
a) General Description
The TPS65251 features three synchronous wide input range high efficiency buck
converters. The converters are designed to simplify its application while giving the designer
the option to optimize their usage according to the target application.
the option to optimize their usage according to the target application.
The converters can operate in 5-, 9-, 12- or 15-V systems and have integrated power
transistors. The output voltage can be set externally using a resistor divider to any value
between 0.8 V and close to the input supply. Each converter features enable pin that allows a
delayed start-up for sequencing purposes, soft start pin that allows adjustable soft-start time
by choosing the soft-start capacitor, and a current limit (RLIMx) pin that enables designer to
adjust current limit by selecting an external resistor and optimize the choice of inductor. The
current mode control allows a simple RC compensation.
between 0.8 V and close to the input supply. Each converter features enable pin that allows a
delayed start-up for sequencing purposes, soft start pin that allows adjustable soft-start time
by choosing the soft-start capacitor, and a current limit (RLIMx) pin that enables designer to
adjust current limit by selecting an external resistor and optimize the choice of inductor. The
current mode control allows a simple RC compensation.
The switching frequency of the converters can either be set with an external resistor
connected to ROSC pin or can be synchronized to an external clock connected to SYNC pin if
needed. The switching regulators are designed to operate from 300 kHz to 2.2 MHz. 180° out
of phase operation between Buck 1 and Buck 2, 3 (Buck 2 and 3 run in phase) minimizes the
input filter requirements.
needed. The switching regulators are designed to operate from 300 kHz to 2.2 MHz. 180° out
of phase operation between Buck 1 and Buck 2, 3 (Buck 2 and 3 run in phase) minimizes the
input filter requirements.
32
LC-39LE351
LC-32LE351
17
TPS65251 features a supervisor circuit that monitors each converter output. The PGOOD
pin is asserted once sequencing is done, all PG signals are reported and a selectable end of
reset time lapses. The polarity of the PGOOD signal is active high.
reset time lapses. The polarity of the PGOOD signal is active high.
TPS65251 also features a light load pulse skipping mode (PSM) by allowing the LOW_P
pin tied to V3V. The PSM mode allows for a reduction on the input power supplied to the
system when the host processor is in stand-by (low activity) mode.
system when the host processor is in stand-by (low activity) mode.
b) Features
• Wide Input Supply Voltage Range (4.5 V - 18 V)
• 0.8 V, 1% Accuracy Reference
• Continuous Loading: 3 A (Buck 1), 2 A (Buck 2 and 3)
• Maximum Current: 3.5 A (Buck 1), 2.5 A (Buck 2 and 3)
• Adjustable Switching Frequency 300 kHz - 2.2 MHz Set By External Resistor
• Dedicated Enable for Each Buck
• External Synchronization Pin for Oscillator
• External Enable/Sequencing and Soft Start Pins
• Adjustable Current Limit Set By External Resistor
• Soft Start Pins
• Current-Mode Control With Simple Compensation Circuit
• Power Good
• Optional Low Power Mode Operation for Light Loads
• QFN Package, 40-Pin 6 mm x 6 mm RHA
APPLICATIONS
• Set Top Boxes
• Blu-ray DVD
• Security Camera
• Car Audio/Video
• DTV
• DVR
• 0.8 V, 1% Accuracy Reference
• Continuous Loading: 3 A (Buck 1), 2 A (Buck 2 and 3)
• Maximum Current: 3.5 A (Buck 1), 2.5 A (Buck 2 and 3)
• Adjustable Switching Frequency 300 kHz - 2.2 MHz Set By External Resistor
• Dedicated Enable for Each Buck
• External Synchronization Pin for Oscillator
• External Enable/Sequencing and Soft Start Pins
• Adjustable Current Limit Set By External Resistor
• Soft Start Pins
• Current-Mode Control With Simple Compensation Circuit
• Power Good
• Optional Low Power Mode Operation for Light Loads
• QFN Package, 40-Pin 6 mm x 6 mm RHA
APPLICATIONS
• Set Top Boxes
• Blu-ray DVD
• Security Camera
• Car Audio/Video
• DTV
• DVR
18
Table 5: Recommended operating conditions
Figure 7: Pin description
Click on the first or last page to see other LC-32LE351K (serv.man2) service manuals if exist.