DOWNLOAD Sharp LC-32LE320E (serv.man2) Service Manual ↓ Size: 5.96 MB | Pages: 32 in PDF or view online for FREE

E 

VCR E DVD recorder

E 

Half SCART, which transmits S-Video or CVBS in, and 

CVBS monitor out.

SCART 2

32”
37”

42”

In cases when the decoder needs to receive a signal 

•

from the TV, make sure to select the appropriate input 
source.
Do not connect the decoder to the SCART 2.

•

You cannot connect the VCR with Decoder using a fully 

•

wired SCART cable under the SCART 2 source.

E

SPDIF OUT

R

L

AUDIO IN

19”
22”
26”

19”
22”

26”

32”
37”

42”

32”

37”

42”

In order to receive coded digital stations, a conditional 

access module (CA module) and a Smartcard must be 

inserted in the CI (Common Interface) slot of the TV. 

The CA Module and the Smartcard are not supplied 

accessories. They are usually available from your 

dealer.
inserting the Smartcard into the Ca module

Carefully insert the CA module in the CI slot 

with the contact side forward.
The logo on the CA module must be facing 

outward from the rear of the TV.

It takes about 30 seconds to certify the license key 

•

when you insert a Smartcard into the CI+ compatible 
CA module for the first time. This process may fail when 
there is no antenna input or you have never run “Auto 
installation”.
The CI+ compatible CA module sometimes upgrades 

•

its firmware. You may not receive any TV images before 
upgrading. You can only use the power button during 
upgrading.
The CI+ compatible CA module does not allow you to 

•

output any copy protected programmes using monitor 
out. 
If the TV displays an update confirmation message 

•

for the Smartcard while receiving CI+ compatible 
broadcasts, follow the screen prompts.
Make sure that the CA module is properly inserted.

•

After inserting and activating the CA Module, make 

sure the input source is 

tV.

Press 

menu on the remote control.

Go to 

Features > Common interface.

This menu is only available for digital stations.

•

The content of this menu depends on the provider of the 

•

CA module.

General information on CA module displays.

Adjustment parameters of each Smartcard displays.

You can input numerical values such as passwords here.

SCART cable

Digital audio in

(COAXIAL)

Digital audio cable

Audio cable

HDMI

DVI

PC

HDMI

32”
37”
42”

19”
22”
26”

19”
22”
26”

32”
37”
42”

DVI-I

PC

HDMI

VGA

19”
22”
26”

32”
37”
42”

Resolution 

 Refresh rate 

640 x 480 

 60Hz 

800 x 600 

 56Hz 

800 x 600 

 60Hz 

1024 x 768 

 60Hz 

1280 x 720 

 60Hz 

1280 x 768 

 60Hz 

1360 x 768 

 60Hz 

1280 x 1024   60Hz (Only for 22”/32”/37”/42”) 

1920 x 1080   60Hz (Only for 22”/32”/37”/42”)

Resolution 

 Refresh rate 

480i 

 60Hz 

480p 

 60Hz 

576i 

 50Hz 

576p 

 50Hz 

720p 

 50Hz, 60Hz 

1080i 

 50Hz, 60Hz 

1080p 

 (HDMI, Component only)

 

 50Hz, 60Hz, 24Hz

HDMI cable

DVI-HDMI cable

Ø 3.5 mm stereo mini jack cable 

Ø 3.5 mm stereo mini jack cable 

DVI-I / RGB

Ø 3.5 mm stereo mini jack cable 

conversion cable

RGB cable

No picture

1. 

Connect power cord correctly.

2. 

Turn on power.

3. 

Connect signal cable correctly.

4. 

Press any button on the LCD TV.

Abnormal colours

Connect signal cable correctly.

Twisted picture

1. 

Connect signal cable correctly.

2. 

Please use compatible signal.

Picture too dark

Adjust brightness and contrast.

Audio only, no images

1. 

Please check if input signal is connected correctly.

2. 

TV-RF signal must not be lower than 50dB.

Picture only, no audio

1. 

Connect signal cable correctly.

2. 

Adjust volume to proper level.

3. 

Connect audio signal cable correctly.

4. 

TV-RF signal must not be lower than 50dB.

Cannot use remote control

1. 

Please change battery.

2. 

Turn off power for 10 seconds; and then restart power.

Cannot receive sufficient channels 

through antenna

Please use the Channel Scan function to increase the number of channels 

not included in memory.

No colour

Please adjust the colour setup.

Blinking picture accompanied by 

ghost image

1. 

Check the connection of antenna/signal cable.

2. 

Check if channel is in play mode.

3. 

Press signal source and change input mode.

Broken lines or segments

Adjust antenna.

Keep the TV away from noise sources, such as automobiles, neon lights, 

and hair dryers.

Certain TV channels are blocked 

(Hope to acquire some channels)

Please use the Update Scan method to add the channels not included in 

memory.

Overlapping images or ghost images Please use multi-directional outdoor antenna.

(If your TV is subject to the influence of nearby mountains or buildings).

Cannot use a function

If the item you choose turns gray, that item cannot be selected.

Cannot receive programmes

Please use the Update Scan method to add the channels not included in 

memory.

19o lCD Colour tV,

22o lCD Colour tV,

26o lCD Colour tV,

LCD screen size

19o diagonal

22o diagonal

26o diagonal

Number of dots

3,147,264 dots 

(1366 g 768 g 3 dots)

6,220,800 dots  

(1920 g 1080 g 3 dots)

3,147,264 dots 

(1366 g 768 g 3 dots)

Video Colour System

PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60

TV 

Function

TV-Standard

Analogue

CCIR (B/G, I, D/K, L/L’)

Digital

DVB-T

 

(2K/8K OFDM), DVB-C

Receiving 

Channel

VHF/UHF

ATV : IRA-E69, DVB-T : E5-E69

CATV

S-band, S1–S41ch

TV-Tuning System

Auto Preset 1599 ch, Auto Label, Auto Sort

STEREO/BILINGUAL

NICAM/A2

Audio amplifier

3W g 2

3W g 2

5W g 2

Speaker

30 (H) x 117 (W) x 23 (D) mm

30 (H) x 117 (W) x 23 (D) mm

38 (H) x 164 (W) x 23 (D) mm

Rear

Antenna

UHF/VHF 75 q 

RS-232C

D-sub 9 pin male connector

SCART

SCART (AV input, Y/C input, RGB input, TV output )

PC IN

D-sub 15 pin (AV input), Ø 3.5mm jack (Audio input)

Component

Y/Pb(Cb)/Pr(Cr), RCA pin (L/R)

SPDIF OUT

Digital audio output 

AV OUT

RCA pin (AV output) 

HDMI 1

Digital video and audio input

Side

C. I. (Common Interface)

EN50221, R206001, CI Plus specification

AV IN

RCA pin (AV input)

USB

Software update, multi-media play

Headphones

Ø 3.5mm jack (Audio output)

HDMI 2

Digital video and audio input

OSD language

English, German, French, Italian, Dutch, Spanish, Greek, Portuguese, Swedish, Finnish, 

Russian, Polish, Turkish, Hungarian, Czech, Slovak, Danish, Norwegian, Estonian, Latvian, 

Lithuanian, Slovenian, Bulgarian, Croatian, Romanian, Serbian, Ukrainian, Gaelic, Belarussian.

Power Requirement

AC 220–240 V, 50 Hz

Power Consumption

20 W (Standby < 0.3W)

(Method IEC62087)

30W (Standby < 0.3W)

(Method IEC62087)

45 W (Standby < 0.3W)

(Method IEC62087)

Weight

3.3 kg (Without stand),

3.7 kg (With stand)

4.0 kg (Without stand),

4.5 kg (With stand)

5.7 kg (Without stand),

6.8 kg (With stand)

Operating temperature

0°C to k40°C