Sharp LC-32GD8EK (serv.man10) Service Manual ▷ View online
53
LC-26GA5E
LC-32GA5E
LC-32GD8E/RU
LC-32BT8E/RU
LC-37GD8E/RU
LC-37BT8E/RU
LC-32/37GD8E/RU
LC-32/37BT8E/RU
37
LC-32/37GD8E/RU
LC-32/37BT8E/RU
TROUBLESHOOTING TABLE
(Continued)
NO
NO
NO
YES
YES
Is "EXT4" selected with
button on the remote control?
button on the remote control?
Select "EXT4" with button
on the remote control.
on the remote control.
YES
Is D-SUB-COMPONENT signal
(PCV_R/G/B) sent to pins (1),
(2) and (3) of EXT4-TERMINAL
(SC2303)?
(PCV_R/G/B) sent to pins (1),
(2) and (3) of EXT4-TERMINAL
(SC2303)?
Check D-SUB-adaptor and
external connection.
external connection.
Is D-SUB-COMPONENT signal
(PCV_R/G/B=VIN19/20/21))
sent to pins (174), (173) and
(172) of IC3002 (VCT)?
(PCV_R/G/B=VIN19/20/21))
sent to pins (174), (173) and
(172) of IC3002 (VCT)?
Check EXT4-TERMINAL and
peripheral circuits.
peripheral circuits.
YES
Is LVDS signal (LVDS_0N/0P-3N/3P) sent from pins (141) and (140) - (129) and (128) of IC3002 (VCTP), and is
CLK signal (LVDS_CN/CP) sent from pins (132) and (131)?
CLK signal (LVDS_CN/CP) sent from pins (132) and (131)?
NO
Check pins (192), (170) and
(133) of BU3.3V power line and
pins (185), (169) and (142) of
BU1.8V power line of IC3002
(VCTP), and peripheral circuits.
(133) of BU3.3V power line and
pins (185), (169) and (142) of
BU1.8V power line of IC3002
(VCTP), and peripheral circuits.
YES
Is LVDS signal (LVDS_0N/0P-3N/3P) sent to pins (12) and (13) - (24) and (25) of CONNECTOR CN1 in LCD-
CONT-UNIT, and is CLK signal (LVDS_CN/CP) sent to pins (21) and (22)?
CONT-UNIT, and is CLK signal (LVDS_CN/CP) sent to pins (21) and (22)?
NO
Check CONNECTOR (P2305,
CN1) and Hareness Wire (LV).
CN1) and Hareness Wire (LV).
YES
Is power (LCD5V) supplied to pins (2) – (5) of CONNECTOR CN1 in LCD-CONT-UNIT?
NO
Replace LCD-CONT-UNIT.
<When EXT4 is used for external input>
No EXT4 (15pin-D-SUB-terminal)
output of the external input system.
output of the external input system.
Checklist:
1) Is "INPUT SOURCE" button on the remote control set up correctly? ··· See the operation manual and set "INPUT SOURCE" to "EXT4".
2) Connect the included D-SUB-Adapter-Cable to the COMPONENT terminal of an external device. ··· See the operation manual (use a commercially
available Component-Cable to connect to the external device).
3) Is ANT-CABLE disconnected or connected improperly? ··· Connect it correctly as per the operation manual.
1) Is "INPUT SOURCE" button on the remote control set up correctly? ··· See the operation manual and set "INPUT SOURCE" to "EXT4".
2) Connect the included D-SUB-Adapter-Cable to the COMPONENT terminal of an external device. ··· See the operation manual (use a commercially
available Component-Cable to connect to the external device).
3) Is ANT-CABLE disconnected or connected improperly? ··· Connect it correctly as per the operation manual.
No picture on the display (6)
YES
Check HARNESSWIRE (LV).
Is IC 1705 supplying LCD 5V?
NO
YES
Check IC1705 and peripheral parts.
YES
NO
Change IC1705.
Is LCD5V supplied to pins (31) -
(28) of CONNECTOR (P2305)?
Troubleshooting Table (continued)
54
LC-26GA5E
LC-32GA5E
LC-32/37GD8E/RU
LC-32/37BT8E/RU
38
LC-32/37GD8E/RU
LC-32/37BT8E/RU
TROUBLESHOOTING TABLE
(Continued)
NO
NO
NO
YES
YES
Is "EXT5" selected with
button on the remote control?
button on the remote control?
Select "EXT5" with button
on the remote control.
on the remote control.
YES
Is the type of video signal
(Signal Type) from HDMI-
connected external device set?
(Signal Type) from HDMI-
connected external device set?
From MENU-Option-HDMI
Setup-Signal Type, select a
signal type ("RGB", "YCbCr
4:4:4" or "YCbCr 4:2:2").
Setup-Signal Type, select a
signal type ("RGB", "YCbCr
4:4:4" or "YCbCr 4:2:2").
Is the type of colour signal
(Colour Matrix) from HDMI-
connected external device set?
(Colour Matrix) from HDMI-
connected external device set?
From Option-HDMI Setup-
Colour Matrix, select a color
signal type ("AUTO", "ITU601"
or "ITU709").
Colour Matrix, select a color
signal type ("AUTO", "ITU601"
or "ITU709").
NO
NO
YES
YES
Is TMDS data (RX`
± signal)
sent to pins (1) – (12) of EXT5
(HDMI) terminal (SC1901)?
(HDMI) terminal (SC1901)?
Is I2C signal (SDA/SCL signal)
sent to pins (16) and (15) of
EXT5 (HDMI) terminal? Check
external connection and
peripheral circuits.
sent to pins (16) and (15) of
EXT5 (HDMI) terminal? Check
external connection and
peripheral circuits.
Is 8bit-DIGITAL signal (HDMI-
R/G/B) sent from pins (110) –
(144) of IC1905 (HDMI-
RECEIVER)?
R/G/B) sent from pins (110) –
(144) of IC1905 (HDMI-
RECEIVER)?
Check power supply (3.3/1.8V)
pins (99) and (74) of IC1905,
SDA/SCL signal pins (29) and
(30), and peripheral circuits.
pins (99) and (74) of IC1905,
SDA/SCL signal pins (29) and
(30), and peripheral circuits.
NO
YES
Is 8bit-DIGITAL signal (HDMI-
R/G/B) sent to pins (73) – (50) of
IC3002 (VCT)?
R/G/B) sent to pins (73) – (50) of
IC3002 (VCT)?
Check SDA3/SCL3 signal pins
(27) and (28), interface between
IC1905 and IC3002, and
peripheral circuits.
(27) and (28), interface between
IC1905 and IC3002, and
peripheral circuits.
YES
Is LVDS signal (LVDS_0N/0P-3N/3P) sent from pins (141) and (140) - (129) and (128) of IC3002 (VCTP), and is
CLK signal (LVDS_CN/CP) sent from pins (132) and (131)?
CLK signal (LVDS_CN/CP) sent from pins (132) and (131)?
NO
Check pins (192), (170) and
(133) of BU3.3V power line and
pins (185), (169) and (142) of
BU1.8V power line of IC3002
(VCTP), and peripheral circuits.
(133) of BU3.3V power line and
pins (185), (169) and (142) of
BU1.8V power line of IC3002
(VCTP), and peripheral circuits.
YES
Is LVDS signal (LVDS_0N/0P-3N/3P) sent to pins (12) and (13) - (24) and (25) of CONNECTOR CN1 in LCD-
CONT-UNIT, and is CLK signal (LVDS_CN/CP) sent to pins (21) and (22)?
CONT-UNIT, and is CLK signal (LVDS_CN/CP) sent to pins (21) and (22)?
NO
Check CONNECTOR (P2305,
CN1) and Hareness Wire (LV).
CN1) and Hareness Wire (LV).
Is power (LCD5V) supplied to pins (2) – (5) of CONNECTOR CN1 in LCD-CONT-UNIT?
NO
Replace LCD-CONT-UNIT.
<When EXT5 is used for external input>
No EXT5 (HDMI) output of the
external input system.
external input system.
Checklist:
1) Is "INPUT SOURCE" button on the remote control set up correctly? ··· See the operation manual and set "INPUT SOURCE" to "EXT5".
2) Have you checked the type of video signal sent from HDMI-connected external device? ··· Confirm the type (it should be "RGB", "YCbCr 4:4:4" or
"YCbCr 4:2:2").
3) Have you checked the type of Colour Matrix sent from HDMI-connected external device? ··· Confirm the type (it should be “ITU601’ or “ITU709”.)
4) Is ANT-CABLE disconnected or connected improperly? ··· Connect it correctly as per the operation manual.
1) Is "INPUT SOURCE" button on the remote control set up correctly? ··· See the operation manual and set "INPUT SOURCE" to "EXT5".
2) Have you checked the type of video signal sent from HDMI-connected external device? ··· Confirm the type (it should be "RGB", "YCbCr 4:4:4" or
"YCbCr 4:2:2").
3) Have you checked the type of Colour Matrix sent from HDMI-connected external device? ··· Confirm the type (it should be “ITU601’ or “ITU709”.)
4) Is ANT-CABLE disconnected or connected improperly? ··· Connect it correctly as per the operation manual.
No picture on the display (7)
YES
YES
Check HARNESSWIRE (LV).
Is IC 1705 supplying LCD 5V?
NO
YES
Check IC1705 and peripheral parts.
YES
NO
Change IC1705.
Is LCD5V supplied to pins (31) -
(28) of CONNECTOR (P2305)?
Troubleshooting Table (continued)
55
LC-26GA5E
LC-32GA5E
LC-32GD8E/RU
LC-32BT8E/RU
LC-37GD8E/RU
LC-37BT8E/RU
LC-32/37GD8E/RU
LC-32/37BT8E/RU
39
LC-32/37GD8E/RU
LC-32/37BT8E/RU
TROUBLESHOOTING TABLE
(Continued)
NO
YES
YES
Do all the fluorescent tubes light up?
Check the individual fluorescent
tubes for light-up failure.
tubes for light-up failure.
NO
Is the specified control signal
inputted at IC1 (INV-CTL) on the
inverter unit?
inputted at IC1 (INV-CTL) on the
inverter unit?
Check the line between CN3 and
IC1.
IC1.
NO
Are the Q16-Q19 transistors at the
primary side of T1 functioning?
primary side of T1 functioning?
Replace IC1 (INV-CTL) or check its
peripheral circuits.
peripheral circuits.
NO
Is the secondary circuit of T1-T8
functioning?
functioning?
Replace the T1-T8 transformer for
the fluorescent tubes, or check their
peripheral circuits.
the fluorescent tubes, or check their
peripheral circuits.
Replace any defective fluorescent
tube (s) with new one (s).
tube (s) with new one (s).
NO
YES
Replace the blown-out CP4/CP3/CP1
fuse on the inverter unit. Turn on the
power again. If the fuse gets blown out
again, check the short-circuited spot.
fuse on the inverter unit. Turn on the
power again. If the fuse gets blown out
again, check the short-circuited spot.
Check T1-T8 and their peripheral
circuits as well as Q16-Q19 and their
peripheral circuits.
circuits as well as Q16-Q19 and their
peripheral circuits.
NO
YES
YES
Is the power supplied to CP3 on the
inverter unit?
inverter unit?
Is the CP4/CP3/CP1 fuse in the
inverter unit circuit functioning?
inverter unit circuit functioning?
Check the connection between
power unit and inverter unit.
power unit and inverter unit.
NO
NO
Are there the INV-ON and INV-BRT
signals at P704 on the power unit,
and the (INV-ON and INV-BRT)
signals at SC1702 on the main PWB?
signals at P704 on the power unit,
and the (INV-ON and INV-BRT)
signals at SC1702 on the main PWB?
Check pins (5) and (7) of IC1710
(main PWB).
(main PWB).
YES
YES
YES
YES
Are there control signals (INV-ON,
INV-BRT, PWM-SEL) at CN3 on the
inverter unit?
INV-BRT, PWM-SEL) at CN3 on the
inverter unit?
NO
Check the circuit connected with the
VCC terminal on the inverter control
IC (IC1).
VCC terminal on the inverter control
IC (IC1).
Is the VCC power supplied to the
inverter control IC (IC1) on the
inverter unit?
inverter control IC (IC1) on the
inverter unit?
Backlight failure to light up
<32”>
Troubleshooting Table (continued)
56
LC-26GA5E
LC-32GA5E
LC-32/37GD8E/RU
LC-32/37BT8E/RU
40
LC-32/37GD8E/RU
LC-32/37BT8E/RU
TROUBLESHOOTING TABLE
(Continued)
NO
YES
YES
Do all the fluorescent tubes light up?
Check the individual fluorescent
tubes for light-up failure.
tubes for light-up failure.
NO
Is the specified control signal
inputted at IC7501 (INV-CTL) on the
inverter unit?
inputted at IC7501 (INV-CTL) on the
inverter unit?
Check the line between CN7502 and
IC7501.
IC7501.
NO
Are the Q7528 and Q7525
transistors at the primary side of
T7501 functioning?
transistors at the primary side of
T7501 functioning?
Replace IC7501 (INV-CTL) or check
its peripheral circuits.
its peripheral circuits.
NO
Is the secondary circuit of T7501
functioning?
functioning?
Replace T7501 or the T75**
transformer for the fluorescent tubes,
or check their peripheral circuits.
transformer for the fluorescent tubes,
or check their peripheral circuits.
Replace any defective fluorescent
tube (s) with new one (s).
tube (s) with new one (s).
NO
YES
Replace the blown-out F7501 fuse on
the inverter unit. Turn on the power
again. If the fuse gets blown out
again, check the short-circuited spot.
the inverter unit. Turn on the power
again. If the fuse gets blown out
again, check the short-circuited spot.
Check T7501 and T7502 and their
peripheral circuits as well as IC7501
and their peripheral circuits.
peripheral circuits as well as IC7501
and their peripheral circuits.
NO
YES
YES
Is the power supplied to CN7501 on
the inverter unit?
the inverter unit?
Is the F7501 fuse in the inverter unit
circuit functioning?
circuit functioning?
Check the connection between
power unit and inverter unit.
power unit and inverter unit.
NO
NO
Are there the INV-OFL, INV-OSC,
INV-STB (ON/OFF) signals at P1701
on the main PWB?
INV-STB (ON/OFF) signals at P1701
on the main PWB?
Check pins (5), (7) and (8) of IC1710
(main PWB).
(main PWB).
YES
YES
YES
YES
Are there control signals (INV-OFL,
INV-BRT, INV-OSC, INV-STB (ON))
at CN7502 on the inverter unit?
INV-BRT, INV-OSC, INV-STB (ON))
at CN7502 on the inverter unit?
NO
Check the circuit connected with the
VCC terminal on the inverter control
IC (IC7501).
VCC terminal on the inverter control
IC (IC7501).
Is the VCC power supplied to the
inverter control IC (IC7501) on the
inverter unit?
inverter control IC (IC7501) on the
inverter unit?
Backlight failure to light up
<37”>
Troubleshooting Table (continued)
Click on the first or last page to see other LC-32GD8EK (serv.man10) service manuals if exist.