DOWNLOAD Sharp LC-32GA3E (serv.man8) Service Manual ↓ Size: 46.59 KB | Pages: 12 in PDF or view online for FREE

Model
LC-32GA3E (serv.man8)
Pages
12
Size
46.59 KB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD / Trouble Shooting
File
lc-32ga3e-sm8.pdf
Date
PREV: Sharp LC-32GA3E (serv.man7) Service Manual

Sharp LC-32GA3E (serv.man8) Service Manual ▷ View online

47
LC-32GA3E
LC-37GA3E
TROUBLE SHOOTING TABLE
 (Continued)
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
YES
NO
YES
YES
NO
YES
NO
YES
NO
YES
NO
Data dropout (relating to gray scale)
Noise is caused to the moving picture with the QS drive on.
The backlight does not go on.
The whole screen is whitish (LCD power supply).
Set PATTERN1 
→ 
PATTERN1 on the adjustment process menu 
to "2".  Is the gray scale pattern displayed correctly?
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "1".  Is the gray scale pattern displayed correctly?
Is OSTEMP.AD on Page 1 of the process adjustment mode set at 
255?
Is the harness connected correctly between the inverter GND 
PWB and LCD control PWB?
Is any of the fuses in the power supply unit blown?
Is power supplied to the inverter PWB?
Connect the harness correctly or replace it.
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "1".  Is the gray scale pattern displayed correctly?
Disconnect the FPC from SC4651 and SC4652.  (To protect the 
panel against damage)
Check the power supply voltage supplied to the panel (check at 
SC4651 and SC4652).
Is the harness connected correctly between the PWBs (power 
unit, inverter PWB, inverter GND PWB and LCD control PWB)?
Check the connector and inverter circuit of each fluorescent lamp.
Check the peripheral circuits of IC4501.
Check the video signal circuit.
Is the input voltage at pin (62) of IC2004 (microprocessor) 5V?
The thermistor on the inverter GND PWB is faulty.
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "5".  Is the test pattern displayed correctly at intervals of one 
dot?
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "4".  Is the test pattern displayed correctly at intervals of one 
dot?
Check the connection between SC4651 and SC4652 and check 
the peripheral circuits of IC4501.
Check IC4701 and IC4901 and their peripheral circuits.
Connect the harness correctly or replace it.
Pin (62) of IC2004 (microprocessor) is faulty.
Check the inverter circuit located downstream from the blown 
Is the control signal applied to pin (11) (OFL1) and pin (13) 
(INV.OSC) of CN705 of the power supply unit?
Check IC4702, IC4902 and their peripheral circuits.
Check the line between IC4701 and IC4501.
Check the peripheral circuits of IC4602.
Check the line between IC4901 and IC4501.
47
LC-32GA3E
LC-37GA3E
TROUBLE SHOOTING TABLE
 (Continued)
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
YES
NO
YES
YES
NO
YES
NO
YES
NO
YES
NO
Data dropout (relating to gray scale)
Noise is caused to the moving picture with the QS drive on.
The backlight does not go on.
The whole screen is whitish (LCD power supply).
Set PATTERN1 
→ 
PATTERN1 on the adjustment process menu 
to "2".  Is the gray scale pattern displayed correctly?
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "1".  Is the gray scale pattern displayed correctly?
Is OSTEMP.AD on Page 1 of the process adjustment mode set at 
255?
Is the harness connected correctly between the inverter GND 
PWB and LCD control PWB?
Is any of the fuses in the power supply unit blown?
Is power supplied to the inverter PWB?
Connect the harness correctly or replace it.
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "1".  Is the gray scale pattern displayed correctly?
Disconnect the FPC from SC4651 and SC4652.  (To protect the 
panel against damage)
Check the power supply voltage supplied to the panel (check at 
SC4651 and SC4652).
Is the harness connected correctly between the PWBs (power 
unit, inverter PWB, inverter GND PWB and LCD control PWB)?
Check the connector and inverter circuit of each fluorescent lamp.
Check the peripheral circuits of IC4501.
Check the video signal circuit.
Is the input voltage at pin (62) of IC2004 (microprocessor) 5V?
The thermistor on the inverter GND PWB is faulty.
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "5".  Is the test pattern displayed correctly at intervals of one 
dot?
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "4".  Is the test pattern displayed correctly at intervals of one 
dot?
Check the connection between SC4651 and SC4652 and check 
the peripheral circuits of IC4501.
Check IC4701 and IC4901 and their peripheral circuits.
Connect the harness correctly or replace it.
Pin (62) of IC2004 (microprocessor) is faulty.
Check the inverter circuit located downstream from the blown 
Is the control signal applied to pin (11) (OFL1) and pin (13) 
(INV.OSC) of CN705 of the power supply unit?
Check IC4702, IC4902 and their peripheral circuits.
Check the line between IC4701 and IC4501.
Check the peripheral circuits of IC4602.
Check the line between IC4901 and IC4501.
47
LC-32GA3E
LC-37GA3E
TROUBLE SHOOTING TABLE
 (Continued)
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
YES
NO
YES
YES
NO
YES
NO
YES
NO
YES
NO
Data dropout (relating to gray scale)
Noise is caused to the moving picture with the QS drive on.
The backlight does not go on.
The whole screen is whitish (LCD power supply).
Set PATTERN1 
→ 
PATTERN1 on the adjustment process menu 
to "2".  Is the gray scale pattern displayed correctly?
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "1".  Is the gray scale pattern displayed correctly?
Is OSTEMP.AD on Page 1 of the process adjustment mode set at 
255?
Is the harness connected correctly between the inverter GND 
PWB and LCD control PWB?
Is any of the fuses in the power supply unit blown?
Is power supplied to the inverter PWB?
Connect the harness correctly or replace it.
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "1".  Is the gray scale pattern displayed correctly?
Disconnect the FPC from SC4651 and SC4652.  (To protect the 
panel against damage)
Check the power supply voltage supplied to the panel (check at 
SC4651 and SC4652).
Is the harness connected correctly between the PWBs (power 
unit, inverter PWB, inverter GND PWB and LCD control PWB)?
Check the connector and inverter circuit of each fluorescent lamp.
Check the peripheral circuits of IC4501.
Check the video signal circuit.
Is the input voltage at pin (62) of IC2004 (microprocessor) 5V?
The thermistor on the inverter GND PWB is faulty.
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "5".  Is the test pattern displayed correctly at intervals of one 
dot?
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "4".  Is the test pattern displayed correctly at intervals of one 
dot?
Check the connection between SC4651 and SC4652 and check 
the peripheral circuits of IC4501.
Check IC4701 and IC4901 and their peripheral circuits.
Connect the harness correctly or replace it.
Pin (62) of IC2004 (microprocessor) is faulty.
Check the inverter circuit located downstream from the blown 
Is the control signal applied to pin (11) (OFL1) and pin (13) 
(INV.OSC) of CN705 of the power supply unit?
Check IC4702, IC4902 and their peripheral circuits.
Check the line between IC4701 and IC4501.
Check the peripheral circuits of IC4602.
Check the line between IC4901 and IC4501.
47
LC-32GA3E
LC-37GA3E
TROUBLE SHOOTING TABLE
 (Continued)
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
YES
NO
YES
YES
NO
YES
NO
YES
NO
YES
NO
Data dropout (relating to gray scale)
Noise is caused to the moving picture with the QS drive on.
The backlight does not go on.
The whole screen is whitish (LCD power supply).
Set PATTERN1 
→ 
PATTERN1 on the adjustment process menu 
to "2".  Is the gray scale pattern displayed correctly?
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "1".  Is the gray scale pattern displayed correctly?
Is OSTEMP.AD on Page 1 of the process adjustment mode set at 
255?
Is the harness connected correctly between the inverter GND 
PWB and LCD control PWB?
Is any of the fuses in the power supply unit blown?
Is power supplied to the inverter PWB?
Connect the harness correctly or replace it.
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "1".  Is the gray scale pattern displayed correctly?
Disconnect the FPC from SC4651 and SC4652.  (To protect the 
panel against damage)
Check the power supply voltage supplied to the panel (check at 
SC4651 and SC4652).
Is the harness connected correctly between the PWBs (power 
unit, inverter PWB, inverter GND PWB and LCD control PWB)?
Check the connector and inverter circuit of each fluorescent lamp.
Check the peripheral circuits of IC4501.
Check the video signal circuit.
Is the input voltage at pin (62) of IC2004 (microprocessor) 5V?
The thermistor on the inverter GND PWB is faulty.
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "5".  Is the test pattern displayed correctly at intervals of one 
dot?
Set PATTERN1 
→ 
PATTERN3 on the adjustment process menu 
to "4".  Is the test pattern displayed correctly at intervals of one 
dot?
Check the connection between SC4651 and SC4652 and check 
the peripheral circuits of IC4501.
Check IC4701 and IC4901 and their peripheral circuits.
Connect the harness correctly or replace it.
Pin (62) of IC2004 (microprocessor) is faulty.
Check the inverter circuit located downstream from the blown 
Is the control signal applied to pin (11) (OFL1) and pin (13) 
(INV.OSC) of CN705 of the power supply unit?
Check IC4702, IC4902 and their peripheral circuits.
Check the line between IC4701 and IC4501.
Check the peripheral circuits of IC4602.
Check the line between IC4901 and IC4501.
Page of 12
Display

Sharp LC-32GA3E (serv.man8) Service Manual ▷ Download

Found More:

LC-32GA3E (serv.man8) Service Manuals

Preview DownloadPagesSize
LC-32GA3E (serv.man2) Cover Contents Service Manual 1 41.7 KB
LC-32GA3E (serv.man23) Schematic Diagram Ex Speaker Service Manual 1 71.18 KB
LC-32GA3E (serv.man22) Schematic Diagram Inverter Inverter GND Service Manual 3 177.31 KB
LC-32GA3E (serv.man21) Schematic Diagram Power Service Manual 3 177.31 KB
LC-32GA3E (serv.man20) Schematic Diagram DVI Service Manual 2 609.54 KB
LC-32GA3E (serv.man19) Schematic Diagram Main Service Manual 14 4.71 MB
LC-32GA3E (serv.man18) Schematic Diagram CPU Service Manual 5 1.22 MB
LC-32GA3E (serv.man17) Schematic Diagram LCD Control Service Manual 8 2.6 MB
LC-32GA3E (serv.man16) Schematic Diagram Front Service Manual 1 129.39 KB
LC-32GA3E (serv.man15) Schematic Diagram Key RC-LED Service Manual 1 261.49 KB
LC-32GA3E (serv.man14) Schematic Diagram AV Service Manual 5 2.43 MB
LC-32GA3E (serv.man12) Packing of the set Service Manual 4 31.17 KB
LC-32GA3E (serv.man11) Printed wiring Board Service Manual 26 15.89 MB
LC-32GA3E (serv.man10) Overall Wiring Diagram Service Manual 2 185.1 KB
LC-32GA3E (serv.man9) Block Diagram Service Manual 6 2.16 MB
LC-32GA3E (serv.man7) Adjustment Procedure Service Manual 17 510.05 KB
LC-32GA3E (serv.man6) Removing of Major Parts Service Manual 5 1.62 MB
LC-32GA3E (serv.man5) Dimensions Service Manual 2 166.78 KB
LC-32GA3E (serv.man4) Service Manual 7 958.62 KB
LC-32GA3E (serv.man3) Important Service Safety Precautions Service Manual 2 48.03 KB
LC-32GA3E (serv.man13) Description of Schematic Diagram Service Manual 1 36.54 KB
LC-32GA3E (serv.man25) Configuring an XBOX 360 with your Sharp LCD-TV User Manual / Operation Manual 5 846.53 KB
LC-32GA3E (serv.man26) Part 1 Cover, Contents, Supplied accessories, Preparation, Watching TV, Basic adjustment settings User Manual / Operation Manual 32 1.77 MB
LC-32GA3E (serv.man27) Part 2 Using external equipment, Useful adjustment settings, Useful features, Appendix, Dimensional drawings User Manual / Operation Manual 29 1.71 MB
LC-32GA3E (serv.man28) User Manual / Operation Manual 61 3.39 MB
LC-32GA3E (serv.man24) Parts List Service Manual / Parts Guide 57 1.83 MB
LC-32GA3E Service Manual / Specification 1 9.45 KB
LC-32GA3E (serv.man29) Dark shadows on screen Service Manual / Technical Bulletin 7 1.44 MB
LC-32GA3E (serv.man30) No operation or stuck in standby Service Manual / Technical Bulletin 1 5.72 KB
LC-32GA3E (serv.man31) Printing error in PC compatibility chart Service Manual / Technical Bulletin 1 32.25 KB
LC-32GA3E (serv.man32) Vertical stripped lines at switch on Service Manual / Technical Bulletin 2 96.69 KB

RANDOM: