Sharp LC-32DH57E (serv.man6) Service Manual ▷ View online
LC-32DH57E-BK/RU-BK/S-BK
5 – 1
LC-32DH57E-BK
Service Manual
CHAPTER 5.
MAJOR IC INFOMATIONS
[1] MAJOR IC INFOMATIONS
1. DESCRIPTION OF MAJOR ICs
Ref No.
Name
Part Code
Description
Drawing
No.
[MAIN UNIT]
IC1301
IC1301
VHiAK4341ED-1Y
DAC
AK4341 is 24 bits DAC of 2Vrms output. A newly developed advanced
multiple bit system is adopted in the
multiple bit system is adopted in the
modulator. In this model, this
IC is used to use the audio signal from a digital tuner as an audio out-
put signal of SCART1.
put signal of SCART1.
1/10
IC1302
VHiMT8292N+-1Q
Audio multiplexer
The MediaTek MT8292 introduces the advantages of an input multi-
plexer, the headphone driver and the PGA outputs. The analog input
pins can either independently support GPIO function or provide extra
GPIO pins to use. The analog input pins can either independently sup-
port GPIO function or provide extra GPIO pins to use.
plexer, the headphone driver and the PGA outputs. The analog input
pins can either independently support GPIO function or provide extra
GPIO pins to use. The analog input pins can either independently sup-
port GPIO function or provide extra GPIO pins to use.
1/10
IC1303
VHiS80944NM-1Y
Voltage detector with built-
in delay circuit
in delay circuit
This IC is a highly precision voltage detector (4.4V) with built-in delay
circuit.
In this model, It used as voltage detector of MUTE signal.
circuit.
In this model, It used as voltage detector of MUTE signal.
1/10
IC501
VHi2BR24C21F-1Y
for service
(RH-iXC206WJQZS)
for service
(RH-iXC206WJQZS)
1K E2PROM
This IC is a 1Kbit-2-wire (I2C bus type) serial EEPROM that can be
programmed electrically. The EEPROM chip stores the EDID data of
PC input. This data is controlled through I2C signals.
programmed electrically. The EEPROM chip stores the EDID data of
PC input. This data is controlled through I2C signals.
2/10
IC506
VHiM3221EiP-1Y
RS232C-DRIVER
The MAX3221E is a single driver, single receiver RS-232 solution
operating from a single Vcc supply. The RS-232 pins provide IEC
G1000-4-2 ESD Protection. The device meets the requirements of
TIA/EIA-232-F and provides the electrical interface between an asyn-
chronous communication controller and the serial-port connector.
The charge pump and four small external capacitors allow operation
from a single 3V to 5.5V supply.
operating from a single Vcc supply. The RS-232 pins provide IEC
G1000-4-2 ESD Protection. The device meets the requirements of
TIA/EIA-232-F and provides the electrical interface between an asyn-
chronous communication controller and the serial-port connector.
The charge pump and four small external capacitors allow operation
from a single 3V to 5.5V supply.
2/10
IC1508
VHiSii91873-1Q
HDMI_Port _Processor
The SiI91873 HDMI port processor is the second generation of HDMI
devices that support revision 1.3 of the HDMI specification.
The main feature is as follows.
1) 4-input, 1-output HDMI port processor.
2) Integrated TMDS receiver and transmitter cores capable of receiv-
devices that support revision 1.3 of the HDMI specification.
The main feature is as follows.
1) 4-input, 1-output HDMI port processor.
2) Integrated TMDS receiver and transmitter cores capable of receiv-
ing and transmitting at 2.25Gbps.
3) Supports video resolutions up to 1080p, 60Hz, 12bit or 720p/1080i,
120Hz,12bit.
4) Receiver fully comply with DVI1.0, HDCP1.1 and HDMI1.3 specifi-
cations.
3/10
IC3302
VHiBD6538G+-1Y
USB high side SW
BD6538G is single channel high side powers switch with low ON resis-
tance Nch power MOSFET.
Rich safety functions such as over current detection, Thermal shut-
down (TSD), under voltage lock out (UVLO) and soft start function
which are required for the power supply port protection are integrated
into 1chip.
tance Nch power MOSFET.
Rich safety functions such as over current detection, Thermal shut-
down (TSD), under voltage lock out (UVLO) and soft start function
which are required for the power supply port protection are integrated
into 1chip.
4/10
IC3303
RH-iXC758WJQZQ
VCT & Main CPU
This IC is Video Processor & MAIN CPU.
In this IC, the decode processing and the video signal processing are
done.
Moreover, OSD is generated here and added to a picture signal.
In this IC, the decode processing and the video signal processing are
done.
Moreover, OSD is generated here and added to a picture signal.
4/10
IC3304
VHiS80928NM-1Y
Voltage detector with built-
in delay circuit
in delay circuit
This IC is a highly precision voltage detector (2.8V) with built-in delay
circuit. In this model, It uses as RESET signal of IC3303.
circuit. In this model, It uses as RESET signal of IC3303.
4/10
IC3305
VHiS80920NM-1Y
Voltage detector with built-
in delay circuit
in delay circuit
This IC is a highly precision voltage detector (2.0V) with built-in delay
circuit. In this model, It used as a D-POW signal generator.
circuit. In this model, It used as a D-POW signal generator.
4/10
IC3501/2
RH-iXC505WJQZQ
512Mb-DDR2-SDRAM
This IC is 512Mb DDR2 SDRAM.
This IC operates as a memory of IC3303 (Video Processor). ***
This IC operates as a memory of IC3303 (Video Processor). ***
5/10
IC8403
RH-iXC788WJN2Y
2Mb-FLASH
This IC is 2Mbit CMOS 3.0 Volt Flash Memory with 50-MHz SPI
(Serial Peripheral Interface) Bus and Small Sector for Boot and
Parameter Storage.
(Serial Peripheral Interface) Bus and Small Sector for Boot and
Parameter Storage.
6/10
IC8401
RH-iXC721WJQZQ
512Mb-NAND-FLASH
This IC is 512Mb NAND flash memory.
This IC stores the software data that processes the system of TV such
as the graphic processing, the LCD controls, and backlights etc.
This IC stores the software data that processes the system of TV such
as the graphic processing, the LCD controls, and backlights etc.
6/10
IC8455
VHiBR24S64F-1Y
I2C bus type-64K
E2PROM
E2PROM
The BR24S64F is a 64Kbit-2-wire (I2C bus type) serial EEPROM that
can be programmed electrically.
This IC stores the menu data and the adjustment value data of adjust-
ment process mode etc.
The data is given out by commands from the main microprocessor.
can be programmed electrically.
This IC stores the menu data and the adjustment value data of adjust-
ment process mode etc.
The data is given out by commands from the main microprocessor.
6/10
LC-32DH57E-BK/RU-BK/S-BK
5 – 2
IC4402
VHiAOZ1320C-1Y
SMART LOAD SW
The AOZ1320 is a P-channel high-side load switch with controlled
slew rate. AOZ1320-04 have a slew rate of 1ms.
slew rate. AOZ1320-04 have a slew rate of 1ms.
7/10
IC4401
VHiMT8295AE-1Q
IC Controller
This is a control IC for PCMCIA cards. This controls information on IC
cards inserted into the PCMCIA card slot (SC4401) or information on
software version upgrade cards saved on flash memories to transfer
the data to CPUs and memories.
cards inserted into the PCMCIA card slot (SC4401) or information on
software version upgrade cards saved on flash memories to transfer
the data to CPUs and memories.
7/10
IC2701
VHiYDA148QZ-1Y
A-AMP
This IC is a digital audio power amplifier. It is mounted by 32QFN
small package with 15W or less stereo. it drives by 10W in 26, and 32
types.
small package with 15W or less stereo. it drives by 10W in 26, and 32
types.
9/10
IC9605
VHiLV5893M+-1Y
1CH-SW-REG
BU3.3V-REG
BU3.3V-REG
LV5893M is 1.8A 1ch step down switching regulator.
In this model, it generate BU3.3V.
In this model, it generate BU3.3V.
10/10
IC9608
VHiLV5893M+-1Y
1CH-SW-REG
D5V-REG
D5V-REG
LV5893M is 1.8A 1ch step down switching regulator.
In this model, it generate D5V.
In this model, it generate D5V.
10/10
IC9606
VHiLV5805M+-1Y
1CH-SW-REG
D1.8V-REG
D1.8V-REG
LV5805M is 2A 1ch step down switching regulator.
In this model, it generate D1.8V.
In this model, it generate D1.8V.
10/10
IC9611
VHiTCR5SB25-1Y
1CH-SW-REG
2.5V-REG
2.5V-REG
The TCR5SB25 is CMOS general-purpose single-output voltage regu-
lators with an on/off control input, featuring low dropout voltage and
low quiescent bias current. The output current is possible up to 200mA
or less. In this model, it generate CPU2.5V.
lators with an on/off control input, featuring low dropout voltage and
low quiescent bias current. The output current is possible up to 200mA
or less. In this model, it generate CPU2.5V.
10/10
IC9604
VHiLV58072M-1Y
1CH-SW-REG
D1.1V-REG
D1.1V-REG
LV58072M is 3A 1ch step down switching regulator.
In this model, it generate D1.1V.
In this model, it generate D1.1V.
10/10
IC9607
VHiS80944NM-1Y
Voltage detector with built-
in delay circuit
in delay circuit
This IC is a highly precision voltage detector with built-in delay circuit.
In this model, It used as enable signal of BU3.3V_REG.
In this model, It used as enable signal of BU3.3V_REG.
10/10
IC2601
IC9601
IC9601
VHiHC2G66DP-1Y
Bilateral Switch
This IC is provides a dual analog switch. Each switch has two pins for
input or output and an active HIGH enable input.
input or output and an active HIGH enable input.
8/10
10/10
10/10
[POWER UNIT]
IC7201
IC7201
VHiSTRY64761E
SWING-P-CTL
This product is hybrid IC for the pseudoresonant switching power sup-
ply with built-in power MOSFET and multifunctional control IC. Highly
effective and the low noise are achieved by a pseudoresonance and
the bottoms ticket operation at the normal operation, and low power
consumption is achieved at the standby by the thing that intermittent
oscillates.
ply with built-in power MOSFET and multifunctional control IC. Highly
effective and the low noise are achieved by a pseudoresonance and
the bottoms ticket operation at the normal operation, and low power
consumption is achieved at the standby by the thing that intermittent
oscillates.
IC7101
VHiNCP1606B-1Y
Power Factor Controller
The NCP1606 is an active power factor controller specifically
designed for use as a pre-converter in electronic ballasts, ac-dc adapt-
ers and other medium power off line converters.
designed for use as a pre-converter in electronic ballasts, ac-dc adapt-
ers and other medium power off line converters.
[INVERTER UNIT]
IC7700
IC7700
VHiBD9897FS-1Y
DC/AC-CONVERTER
BD9897FS is IC for DC-AC inverter control. Functions of soft start cir-
cuit, timer latch circuit, and under voltage lock output circuit (UVLO),
etc. are built into this IC.
cuit, timer latch circuit, and under voltage lock output circuit (UVLO),
etc. are built into this IC.
Ref No.
Name
Part Code
Description
Drawing
No.
LC-32DH57E-BK/RU-BK/S-BK
5 – 3
2. Detailed ICs Information
2.1. IC1301 (VHiAK4341ED-1Y)
2.1.1 Block Diagram
2.1.2 Pin Connections and short description
Pin No.
Pin Name
I/O
Pin Function
1
MCLK
I
Master clock input pin. An external TTL clock should be input on this pin.
2
BICK
I
Audio serial data clock pin.
3
SDTI
I
Audio serial data input pin.
4
LRCK
I
L/R clock pin.
5
RDN
I
Power-down mode pin.
When at “L”, the AK4341 is in the power-down mode, held in reset and AOUTL/R are held in VCOM.
The AK4341 must be reset once upon power-up.
When at “L”, the AK4341 is in the power-down mode, held in reset and AOUTL/R are held in VCOM.
The AK4341 must be reset once upon power-up.
6
SMUTE
I
Soft mute pin in parallel control mode.
“H”: Enable, “L”: Disable
“H”: Enable, “L”: Disable
7
ACKS
I
Auto setting mode pin.
“L”: Manual setting mode, “H”: Auto setting mode.
“L”: Manual setting mode, “H”: Auto setting mode.
8
DIF
I
Audio data interface format pin.
“L”: 24bit MSB justified, “H”; I2S.
“L”: 24bit MSB justified, “H”; I2S.
9
DEM
I
De-emphasis enable pin.
“H”: Enable, “L”: Disable
“H”: Enable, “L”: Disable
10
AOUTR
O
Rch analog output pin.
When PDN pin = “L”, outputs VCOM voltage.
When PDN pin = “L”, outputs VCOM voltage.
11
AOUTL
O
Lch analog output pin.
When PDN pin = “L”, outputs VCOM voltage.
When PDN pin = “L”, outputs VCOM voltage.
12
HVDD
I
Output buffer power supply pin.
Normally connected to VSS with a 0.1
Normally connected to VSS with a 0.1
µF ceramic capacitor in parallel with a 10µF electrolytic cap.
13
VSS
—
Ground pin.
14
VDD
—
DAC power supply pin.
15
VCOM
O
DAC common voltage pin.
Normally connected to VSS with a 10
Normally connected to VSS with a 10
µF electrolytic cap.
Outputs VCOM VDD voltage either PDN pin = “L” or “H”.
16
GAIN
I
Gain control pin.
“H”: +6dB, “L”: 0dB, open: +12dB.
When PDN = “H”, the gain pin is connected to VDD and VSS with 50k
“H”: +6dB, “L”: 0dB, open: +12dB.
When PDN = “H”, the gain pin is connected to VDD and VSS with 50k
Ω resister and held to VDD/2 when open.
When PDN = “L”, connected to VSS with 50k
Ω resister.
LC-32DH57E-BK/RU-BK/S-BK
5 – 4
2.2. IC1302 (VHiMT8292N+-1Y)
2.2.1 Block Diagram