DOWNLOAD Sharp LC-32D44E (serv.man11) Service Manual ↓ Size: 4.27 MB | Pages: 40 in PDF or view online for FREE

Menu Operation: A (page 12)
Produce a clearer image. (Off, High, Low)

HDMI (High-Definition Multimedia Interface) terminal 
selection.

To watch an HDMI equipment image, select 
“EXT6” or “EXT7” (the terminal which you are 
using) from “INPUT SOURCE” menu using 

b 

on the remote control unit or TV.

Press MENU and the MENU screen displays.

Press 

c/d to select “Option”.

Press 

a/b to select  “HDMI Setup”, and then 

press OK.

•  “HDMI Setup” is displayed only when “EXT6” or 

“EXT7” is selected from the INPUT SOURCE menu.

MENU    

[Option ... HDMI Setup]

Option

Audio Only

DNR

HDMI Setup

[Off]

Press 

a/b to select the desired item, and then 

press OK.

Press 

a/b/c/d to select the desired setting, 

and then press OK.

RGB/YCbCr 4:4:4/
YCbCr 4:2:2

Select the video signal 
type from the HDMI 
terminal. 

ITU601/ITU709

Select the internal 
colour space 
conversion method 
when an RGB signal 
is input. 

Normal/Enhanced

Select the signal 
amplitude range. 
Usually, select 
“Normal”.

Disable/Enable

Set whether or not 
to use WIDE MODE 
based on signal 
recognition, including 
an HDMI signal.

Digital/Analogue

Select “Digital” for 
audio signal via the 
HDMI terminal. Select 
“Analogue” for audio 
signal via the AUDIO 
jack.

NOTE
•  Refer to your external equipment operation manual for the 

signal type.

•  Items marked * may be greyed out (with 

4) depending on 

the type of signal input from the external equipment.

•  Item marked ** is only available when EXT6 is selected.

Menu Operation: A (page 12)
For setting the signal type of external equipment.

Y/C, CVBS, RGB

Y/C, CVBS, RGB

NOTE
•  If no (colour) image displays, try to change the other 

•  Check the operation manual of the external equipment for 

the signal type.

•  TV, EXT3, EXT4, EXT5, EXT6 and EXT7 are not displayed in 

Input Select.

•  If both CVBS and RGB signals are input to EXT 1 or EXT 

2 using a SCART cable, the TV may output an RGB signal 
even though you have designated CVBS for the respective 
terminal. This happens due to the setting of your external 
equipment.

Menu Operation: A (page 12)
You can change the colour system to one that is 
compatible with the image on the screen. (AUTO, PAL, 
SECAM, NTSC3.58, NTSC4.43, PAL-60)

NOTE
•  Factory preset value is “AUTO”.
•  If “AUTO” is selected, colour system for each channel is 

automatically set. If an image does not display clearly, 
select another colour system (e.g. PAL, SECAM).

•  “NTSC3.58”, “NTSC4.43” and “PAL-60” cannot be 

selected in TV tuner mode.

LC-32D44E-gb.indd   19

LC-32D44E-gb.indd   19

2008/02/21   9:44:44

2008/02/21   9:44:44

You can select the picture size. Selectable picture size 
varies with the type of signal received.

Normal: For 4:3 “standard” pictures. A side bar 

appears on each side.

Zoom 14:9: For 14:9 letterbox pictures. A thin side bar 

appears on each side, and you may see bars on the 
top and bottom with some programmes.

Panorama: In this mode the picture is progressively 

stretched toward each side of the screen.

Full: For 16:9 squeeze pictures.
Cinema 16:9: For 16:9 letterbox pictures. Bars 

may appear on the top and bottom with some 
programmes.

Cinema 14:9: For 14:9 letterbox pictures. Bars 

may appear on the top and bottom with some 
programmes.

Full: Display with the Overscan image. Crop all sides of 

screen.

Press 

f.

•  The WIDE MODE menu displays.
•  The menu lists the wide mode options selectable for 

the type of video signal currently received.

Press 

f or 

a/b while the WIDE MODE menu 

displays on the screen.

•  As you toggle down the options, each is immediately 

reflected on the screen. No need to press OK.

If you set WSS and 4:3 Mode in the Setup menu on 
page 18, the optimum WIDE MODE is automatically 
chosen for every broadcast, VCR or DVD containing 
the WSS information.

To enable Auto Selection, set WSS in the Setup menu 
to “On”. (See page 18.)

To set the type of the wide screen, select “Normal” or 
“Panorama” in the 4:3 Mode menu. (See page 18.)

NOTE
•  If the signal contains no WSS information, Auto Selection 

will not function even when the WSS option is enabled.

You can select the picture size.

Press 

f.

•  The WIDE MODE menu displays.

Press 

f or 

a/b to select a desired item on 

the menu.

NOTE
•  Connect the PC before making adjustments. (See page 

10.)

•  Selectable picture size may vary with input signal type.

Normal: Keeps the original aspect ratio in a full screen 

display.

Full: An image fully fills the screen. 

4:3 Mode set to “Normal”

4:3 Mode set to “Panorama”

LC-32D44E-gb.indd   20

LC-32D44E-gb.indd   20

2008/02/21   9:44:45

2008/02/21   9:44:45

You can freeze a motion picture on the screen.

Press 

3.

Press 

3 again to exit still image.

NOTE
•  When this function is not available, “No still image display 

available.” will display.

•  The still image automatically goes out after 30 minutes.

Teletext broadcasts pages of information and 
entertainment to specially equipped television sets. 
Your TV receives Teletext signals broadcast by a TV 
network, and decodes them into graphical format for 
viewing. News, weather and sports information, stock 
exchange prices and programme previews are among 
the many services available.

Select a TV channel or external input source 
providing the Teletext programme.

Press 

m to display the Teletext.

Press 

m again to display the Teletext on the 

right screen and normal image on the left 
screen.

•  Each time you press 

m, the screen switches as 

shown below.

* May appear in DTV input mode.
•  If you select a programme with no Teletext signal, 

“No Teletext available.” displays.

•  The same message displays during other modes if no 

Teletext signal is available.

NOTE
•  Teletext will not work if the selected signal type is RGB. 

(See page 19.)

You can display the time information included in the 
DTV and Teletext broadcasts.

NOTE
•  Skip step 1 if receiving DTV broadcasts.

Select a TV channel providing Teletext 
information. (The time information is 
automatically captured.)

Press 

p. The channel display will appear on 

the TV.

Press 

p again within the several seconds that 

the channel display is on the screen.

 

Time information will display below the channel 
display for several seconds.

Even when you change the TV channel, you can 
display the time information with steps 2 and 3 
above.

NOTE
•  The time display cannot be stored once the power is 

turned off. When you turn on the power, perform steps 1 to 
4 again.

•  If acquired successfully, the time information will appear in 

the upper-right corner of the screen by pressing MENU.

r/s)

Increase or decrease the page number.

Select a group or block of pages displayed in 
the coloured  brackets at the bottom of the 
screen by pressing the corresponding Colour 
(Red/Green/Yellow/Blue) on the remote 
control unit.

Directly select any page from 100 to 899 by 
using 0–9.

k (Reveal 
hidden Teletext)

Reveal or hide hidden information such as an 
answer to a quiz.

3 (Freeze/
Hold)

Stop updating Teletext pages automatically or 
release the hold mode. 

[ (Subtitle for 
Teletext)

Display the subtitle or exit the subtitle screen.
•  Subtitle will not be displayed when the 

service does not contain the subtitle 
information.

1 (Subpage)

Reveal or hide subpages.
•  Red button: Move to the previous subpage.
•  Green button: Move to the following 

subpage.

•  These two buttons are shown on the screen 

by the signs 

l and k.

User for LC-32D44E:
•  Subtitle is set to off when the power is 

turned on.

User for LC-32D44S:
•  Subtitle is set to on when the power is 

turned on.

LC-32D44E-gb.indd   21

LC-32D44E-gb.indd   21

2008/02/21   9:44:46

2008/02/21   9:44:46

Use the following buttons on the remote control unit to 
operate the DTV Menu.

[: 

Press to display the subtitle selection 
screen.

m: 

Press to display TELETEXT or start the 
MHEG5 presentation, if available.

 - 

 : 

Aside from direct channel entry, each of the 

 - 

 numeric buttons have a unique 

function assigned in the Programme Setup 
screen. 

DTV: 

Press to access DTV mode.

EPG: 

Press to open the EPG screen.

ESG: 

Press to open the ESG screen.

RADIO: 

Press to switch between TV and RADIO 
mode.
•  Due to the large variation in transmitted 

volume levels in RADIO mode, some 
stations will produce distortion if the 
volume level is set too high.

2: 

Press to open the multi audio screen.

DTV MENU: 

Press to open or close the DTV Menu 
screen.

p: 

Press to open the service banner or view 
detailed information from the EPG/ESG 
screen.

a/b/c/d: 

Press to select a desired item on the screen 
or adjust a selected item.

OK: 

Press to go to the next step or complete the 
setting.

 

Press to open the Programme List when 
no other menu screen is active. (Except 
external input.)

END: 

Press to exit the current menu screen 
without saving the changes.

Colour: 

Each of the coloured buttons have a unique 
function assigned in the menu screen. 

RETURN: 

Press to return to the previous step.

1  Language

•  To customise the language preference for audio and 

MHEG5 application.

2  Programme Setup

•  To configure various settings for each service. These 

include: Fav(ourite), Lock, Move, Move To, Skip, 
Select, Erase, Label, and View functions. 

3  Installation

•  To scan all services available in your area, or to label/

erase/re-scan the selected carrier.

4  System Setup

•  To configure On-Screen Display and Child Lock 

settings. 

5  Accessories

•  To display the current version of the software or to 

allow the software upgrade to take place.

6  Common Interface

•  To display the current Common Interface details.

7  Navigation buttons

•  To navigate within the DTV Menu screen.

1 Press 

DTV or 

b to access the DTV mode. 

2 Press 

DTV MENU and the DTV Menu screen 

displays.

3 Press 

c/d to select the desired menu, and 

then press OK if necessary.

•  From this point, menu operations differ depending on 

the item you are going to adjust. See the respective 
section of the menu operation.

•  You cannot select any DTV-related menu items 

unless “Auto Installation” has been completed.

• Press RADIO to switch between DTV and Radio 

mode.

•  To exit the current screen without saving the change, 

press END.

1

3

4

6

5

2

7

LC-32D44E-gb.indd   22

LC-32D44E-gb.indd   22

2008/02/21   9:44:46

2008/02/21   9:44:46