DOWNLOAD Sharp LC-32D12EA (serv.man2) Service Manual ↓ Size: 11.31 MB | Pages: 116 in PDF or view online for FREE

TO EXPOSED

METAL PARTS

CONNECT TO

KNOWN EARTH

GROUND

DVM

AC SCALE

1.5k ohm

10W

0.15 µF

TEST PROBE

Many electrical and mechanical parts in LCD television have special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily 

increased by using replacement components rated for higher voltage, wattage, etc.

Replacement parts which have these special safety characteristics are identified in this manual; electrical components 

having such features are identified by    “    “.

For continued protection, replacement parts must be identical to those used in the original circuit.
The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended 

replacement parts shown in this service manual, may create shock, fire or other hazards.

1. For continued safety, no modification of any circuit should be attempted.

2. Disconnect AC power before servicing.

1. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the 

chassis and other metal parts in the receiver.

2. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and 

compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.

3. To be sure that no shock hazard exists, check for leakage current in the following manner. 

• Plug the AC cord directly into a 220~240 volt AC outlet. (Do not use an isolation transformer for this test).

•Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal 

cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.

•A true RMS reading multimeter should be used for this test, especially where the equipment uses a switch mode 

power supply which may result in very non-sinusoidal leakage current.

•Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, 

screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.

All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must 

be used only for the purpose of completing these checks.)

Any reading of 1.05V peak (this corresponds to 0.7 mA. peak AC.) or more is excessive and indicates a potential shock 

hazard which must be corrected before returning the monitor to the owner.

!

  CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF
  FIRE REPLACE ONLY WITH SAME TYPE  
 

F800, F801 (T 3.15A  250V  RADIAL)

e:

Indicates lead-free solder of tin, silver and copper.

“ALL  PWB” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the 

PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.

Example:

When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead 

wire solder may cause damage or accident due to cracks.

As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you to 
use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our 

service station or service branch in your area.

As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder by 

40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended 

period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be 

exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition.

Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and 

off the power of the bit as required.

If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every 

use of it.

When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.

Be careful when replacing parts with polarity indication on the PWB silk.

Lead-free wire solder for servicing.

Indicates lead-free solder of tin, silver and nickel.

Sn-Ag-Ni

English   - 38 -

00_MB60_[GB]_1910UK_IDTV_PVR_NICKEL16_32883W_YPBPR_ROCKER_10075570_5019xxxx.indd   38

07.09.2011   15:46:29

English   - 8 -

Standby

Image size / Zooms videos (in Media Browser 

video mode)

Sleep Timer

Mono / Stereo - Dual I-II / Currrent Language (*) 

(in DVB channels)

Favourite Mode Selection (in DVB channels)

Numeric buttons

Electronic programme guide (in DVB channels)

No function

Media Browser

Navigation buttons (Up/Down/Left/Right)

No function

Recordings Library

Programme Down / Page up - Programme Up / 

Page down

Mute

Programme recording

Pause (in Media Browser mode) / Timeshift 

recording

Rapid reverse (in Media Browser mode)

Play (in Media Browser mode)

Red button

Green button / List Schedule (in EPG) / Tag 

/ Untag All (in favourite list) / Play-Slideshow 
(in Media Browser) / Loop-Shuffl e (in Media 
Browser)

Picture mode selection / Changes picture mode 

(in Media Browser video mode) 

No function

Teletext / Mix (in TXT mode)

Subtitle on-off (in DVB channels)

Previous programme

AV / Source selection

Menu on-off

Okay (Confi rm) / Hold (in TXT mode) / Edit 

Channel List

Exit / Return / Index page (in TXT mode)

No function

Info / Reveal (in TXT mode)

Volume Up / Down

No function

No function

Rapid advance (in Media Browser mode)

CH

V

Stop (in Media Browser mode)

Blue button / Edit Channel List / Filter (In 

Favourite List&EPG) 

Yellow button / Timeline Schedule (in EPG)

00_MB60_[GB]_1910UK_IDTV_PVR_NICKEL16_32883W_YPBPR_ROCKER_10075570_5019xxxx.indd   8

07.09.2011   15:45:59