DOWNLOAD Sharp LC-26SA1E (serv.man3) Service Manual ↓ Size: 1.59 MB | Pages: 28 in PDF or view online for FREE

Model
LC-26SA1E (serv.man3)
Pages
28
Size
1.59 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
TV / LCD
File
lc-26sa1e-sm3.pdf
Date

Sharp LC-26SA1E (serv.man3) User Manual / Operation Manual ▷ View online

5
Remote control unit
Quick guide
Selectable items
NICAM STEREO, MONO
NICAM CH A, NICAM CH B,
NICAM CH AB, MONO
NICAM MONO, MONO
Signal
Stereo
Bilingual
Monaural
Selectable items
STEREO, MONO
CH A, CH B, CH AB
MONO
Signal
Stereo
Bilingual
Monaural
NOTE
• When no signal is input, the sound mode will display “MONO”.
 3 (Freeze/Hold)
(See page 20.)
B (Standby/On)
Enter standby mode or turn on the
power.
(See page 7.)
[ (Subtitle for Teletext)
(See page 20.)
END
Exit the menu screen.
i (k/l) (Volume)
i (k) Increase the volume.
i (l) Decrease the volume.
0–9
Set the channel in TV mode.
Set the page in Teletext mode.
A (Flashback)
Press to return to the previous
image in normal viewing mode.
2 (Sound mode)
Select the sound multiplex mode.
(See below.)
SURROUND
Switch the surround effects on and off.
(Subpage)
(See page 20.)
SLEEP
Set the sleep timer on (in units of 30 min.
up to max. 2 hr. 30 min.) and off.
k (Reveal hidden Teletext)
(See page 20.)
p (Display information)
(See page 20.)
RETURN
Return to the previous menu screen.
e (Mute)
Switch the sound on and off.
b (INPUT SOURCE)
Select an input source.
(TV, EXT1, EXT2, EXT3, EXT4, EXT5)
(See page 8.)
f (WIDE MODE)
Select the wide mode.
(See page 19.)
Set the area of magnification in Teletext
mode. (See page 20.)
MENU
Display the MENU screen.
(See page 10.)
P (r/s)
TV: Select the channel.
External: Switch to TV input mode.
Teletext: Move to the next/previous page.
OK
Execute a command within the menu
screen.
Display the programme list. (Except
external input.)
(See page 7.)
a/b/c/d (Cursor)
Select a desired item on the setting
screen.
Colour (Red/Green/Yellow/Blue)
(See page 20.)
m (Teletext)
(See page 20.)
NICAM TV broadcasts selection
A2 TV broadcasts selection
LC-32SA1E_GB_a
06.7.25, 11:27 AM
5
6
TV (Front view)
Quick guide
TV (Rear view)
AC INPUT terminal
OPC sensor
Remote control sensor
B (Standby/On) indicator
OPC indicator
a (Power button)
b (Input button)
i (l/k)
(Volume buttons)
P (s/r)
(Programme [channel] buttons)
SLEEP indicator
EXT 2 (RGB) terminal
EXT 3 terminals
Headphone jack
EXT 1 (RGB) terminal
EXT 5 (HDMI/AUDIO)
terminals
Antenna input terminal
OUTPUT (Audio) terminals
EXT 4 terminals
RS-232C terminal
For LC-26SA1E,
LC-26SV1E
LC-32SA1E_GB_a
06.7.25, 11:27 AM
6
7
Turning on the power
Press a on the TV.
• The B indicator on the TV changes from red to green.
NOTE
• If you are not going to use this TV for a long period of
time, be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when a is
turned off.
Initial auto installation
When the TV powers on for the first time after purchase,
the initial auto installation is invoked. You can
automatically set language, country and channels in
successive operations.
1
Setting the on-screen display language
1 Press a/b/c/d to select the desired language
listed on the screen.
2 Press OK to enter the setting.
2
Setting the country or area
1 Press  a/b/c/d to select your country or area
listed on the screen.
2 Press OK to enter the setting.
• The programme auto search starts at the same time.
After this setting, auto search starts with the following
order.
1 Programme auto search
2 Auto labelling
3 Auto sorting
4 Preset download
You do not need to do anything during the auto search.
NOTE
• The initial auto installation functions only once. If the initial
auto installation is not completed, (ex: When menu screen
disappeared by not operating for a few minutes, when
the power shut down, etc.), try Auto Installation from the
Setup menu. (See page 14.)
• The initial auto installation stops by pressing RETURN.
Standby mode
Press B on the remote control unit.
• The TV enters standby mode and the image on the screen
disappears.
• The B indicator on the TV changes from green to red.
Turning off the power
Press a on the TV.
• The B indicator on the TV gradually turns off.
• When the TV is turned off by a, you cannot turn on the
power by pressing B on the remote control unit.
Off
Red
Green
Display status indicator
Power off
The TV is in standby mode.
The TV is on.
Using the programme list
You can also select the desired channel from
programme list instead of using 0-9 numeric buttons
or P (
r
r
r
r
r/s
s
s
s
s).
The setup menu disappears and you can watch the
programme on channel 1.
1
Press  OK when no other menu screen is
displayed. (Except external input.)
2
Press a/b to select the desired channel to tune
in, and then press OK.
3
Press END to exit the Programme List.
Quick guide
LC-32SA1E_GB_a
06.7.25, 11:27 AM
7
8
Using external equipment
Setting the input source
To view external source images, select the input source using b on the remote control unit or TV.
NOTE
• The cables marked with * are commercially available items.
Connecting a VCR
You can use the EXT 1 or 2 terminals when connecting
a VCR and other audiovisual equipment.
If your VCR supports TV-VCR advanced AV Link
systems, you can connect the VCR to the EXT 2
terminal of the TV using the fully-wired SCART cable.
NOTE
• TV-VCR advanced AV Link systems may not be compatible
with some external sources.
• TV-OUT from EXT1 is not outputted when EXT5 (HDMI) is
selected as the input.
YP
B
(
C
B)
P
R
(
C
R)
COMPONENT
EXT 4
ø 3.5 mm stereo
minijack cable*
Component
cable*
3 RCA to 15-pin
D-sub adapter
(Supplied)
VCR
Decoder
SCART cable*
SCART cable*
EXT 1 or 2
VIDEO
S-VIDEO
L-AUDIO-R
AV OUTPUT
Connecting a DVD player
You can use the EXT 2, 3, 4 or 5 (HDMI) terminals
when connecting to a DVD player and other
audiovisual equipment.
DVD player
AUDIO cable*
EXT 3
Composite
video cable*
DVD player
HDMI cable*
When using an HDMI-DVI
conversion adapter/cable,
input the Audio signal here.
EXT 5
or
DVD player
S-video cable*
NOTE
• When connecting an HDMI-DVI conversion adapter/cable
to the HDMI terminal, the image may not come in clearly.
NOTE
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
terminals.
A game console, camcorder and some other
audiovisual equipment are conveniently connected
using the EXT 3 terminals.
NOTE
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
terminals.
Connecting a game console or
camcorder
Game console Camcorder
or
S-video cable*
Composite
video cable*
AUDIO cable*
EXT 3
VIDEO
S-VIDEO
L-AUDIO-R
AV OUTPUT
LC-32SA1E_GB_a
06.7.25, 11:27 AM
8
Page of 28
Display

Click on the first or last page to see other LC-26SA1E (serv.man3) service manuals if exist.