DOWNLOAD Sharp LC-26SA1E (serv.man3) Service Manual ↓ Size: 1.59 MB | Pages: 28 in PDF or view online for FREE

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical

leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any

chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.

30

°

30

°

Remote control sensor

5 m

Hold in the tab on the battery cover and pull the
cover towards the direction of the arrow.

Insert two supplied “AA” size batteries.

• Place batteries with their terminals corresponding

to the (e) and (f) indications in the battery
compartment.

Insert the smaller tab of the battery cover into the
opening (1), and press down on the cover until
it clicks in place (2).

Before using the TV for the first time, insert two “AA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AA” size batteries.

Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote
control unit and sensor may prevent proper operation.

• Do not expose the remote control unit to shock.

In addition, do not expose the remote control unit to liquids, and do not
place in an area with high humidity.

• Do not install or place the remote control unit under direct sunlight. The

heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote control sensor

of the TV is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.

1

2

LC-32SA1E_GB_a

06.7.25, 11:27 AM

4

NICAM STEREO, MONO

NICAM CH A, NICAM CH B,
NICAM CH AB, MONO

NICAM MONO, MONO

STEREO, MONO

CH A, CH B, CH AB

MONO

• When no signal is input, the sound mode will display “MONO”.

 3 (Freeze/Hold)

(See page 20.)

B (Standby/On)

Enter standby mode or turn on the

power.

(See page 7.)

[ (Subtitle for Teletext)
(See page 20.)

Exit the menu screen.

i (k/l) (Volume)

i (k) Increase the volume.

i (l) Decrease the volume.

Set the channel in TV mode.

Set the page in Teletext mode.

A (Flashback)

Press to return to the previous

image in normal viewing mode.

2 (Sound mode)

Select the sound multiplex mode.

(See below.)

SURROUND
Switch the surround effects on and off.

1 (Subpage)
(See page 20.)

SLEEP
Set the sleep timer on (in units of 30 min.
up to max. 2 hr. 30 min.) and off.

k (Reveal hidden Teletext)

(See page 20.)

p (Display information)
(See page 20.)

RETURN
Return to the previous menu screen.

e (Mute)
Switch the sound on and off.

b (INPUT SOURCE)
Select an input source.
(TV, EXT1, EXT2, EXT3, EXT4, EXT5)
(See page 8.)

f (WIDE MODE)

Select the wide mode.

(See page 19.)

Set the area of magnification in Teletext

mode. (See page 20.)

MENU
Display the MENU screen.
(See page 10.)

P (r/s)
TV: Select the channel.
External: Switch to TV input mode.
Teletext: Move to the next/previous page.

OK
Execute a command within the menu
screen.
Display the programme list. (Except
external input.)
(See page 7.)

a/b/c/d (Cursor)

Select a desired item on the setting

screen.

(See page 20.)

m (Teletext)

(See page 20.)

LC-32SA1E_GB_a

06.7.25, 11:27 AM

5

AC INPUT terminal

OPC sensor

Remote control sensor

B (Standby/On) indicator

OPC indicator

a (Power button)

b (Input button)

i (l/k)

(Volume buttons)

P (s/r)

(Programme [channel] buttons)

SLEEP indicator

EXT 2 (RGB) terminal

EXT 3 terminals

Headphone jack

EXT 1 (RGB) terminal

EXT 5 (HDMI/AUDIO)
terminals

Antenna input terminal

OUTPUT (Audio) terminals

EXT 4 terminals

RS-232C terminal

LC-32SA1E_GB_a

06.7.25, 11:27 AM

6

Press a on the TV.

• The B indicator on the TV changes from red to green.

• If you are not going to use this TV for a long period of

time, be sure to remove the AC cord from the power outlet.

• Weak electric power is still consumed even when a is

turned off.

When the TV powers on for the first time after purchase,
the initial auto installation is invoked. You can
automatically set language, country and channels in
successive operations.

Setting the on-screen display language

1 Press a/b/c/d to select the desired language

listed on the screen.

2 Press OK to enter the setting.

Setting the country or area

1 Press  a/b/c/d to select your country or area

listed on the screen.

2 Press OK to enter the setting.
• The programme auto search starts at the same time.

After this setting, auto search starts with the following
order.

1 Programme auto search
2 Auto labelling
3 Auto sorting
4 Preset download

You do not need to do anything during the auto search.

• The initial auto installation functions only once. If the initial

auto installation is not completed, (ex: When menu screen
disappeared by not operating for a few minutes, when
the power shut down, etc.), try Auto Installation from the
Setup menu. (See page 14.)

• The initial auto installation stops by pressing RETURN.

Press B on the remote control unit.

• The TV enters standby mode and the image on the screen

disappears.

• The B indicator on the TV changes from green to red.

Press a on the TV.

• The B indicator on the TV gradually turns off.
• When the TV is turned off by a, you cannot turn on the

power by pressing B on the remote control unit.

Off

Red

Green

Power off

The TV is in standby mode.

The TV is on.

You can also select the desired channel from
programme list instead of using 0-9 numeric buttons
or P (

r

r

r

r

r/s

s

s

s

s).

The setup menu disappears and you can watch the
programme on channel 1.

Press  OK when no other menu screen is
displayed. (Except external input.)

Press a/b to select the desired channel to tune
in, and then press OK.

Press END to exit the Programme List.

LC-32SA1E_GB_a

06.7.25, 11:27 AM

7