DOWNLOAD Sharp LC-26SA1E (serv.man3) Service Manual ↓ Size: 1.59 MB | Pages: 28 in PDF or view online for FREE

Model
LC-26SA1E (serv.man3)
Pages
28
Size
1.59 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
TV / LCD
File
lc-26sa1e-sm3.pdf
Date

Sharp LC-26SA1E (serv.man3) User Manual / Operation Manual ▷ View online

3
Quick guide
Attaching the stand
Before attaching (or detaching) stand, unplug the AC cord from the AC INPUT terminal.
1
Confirm the 8 screws supplied with the TV.
Short screws (m4)
(used in step 2)
Long screws (m4)
(used in step 4)
2
Attach the two parts of the stand unit to each other
using the 4 short screws as shown.
3
Insert the stand into the opening on the bottom of
the TV.
4
Insert and tighten the 4 long screws on the rear
of the TV as shown.
NOTE
• To detach the stand, perform the above steps in reverse order.
Before performing work spread cushioning over the base area to lay the TV on, making sure the
area is completely flat. This will prevent it from being damaged.
Setting the TV
Standard DIN45325
plug (IEC 169-2)
75-ohm coaxial cable
Setting the TV on the wall
• This TV should be mounted on the wall only with the wall mount bracket available from SHARP. (See page 23.) The
use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
• Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting
or mounting that results in accident or injury.
• You can ask a qualified service personnel about using an optional bracket to mount the TV to the wall.
Ferrite Core
The Ferrite Core should be permanently attached
and never removed from the AC cord.
AC cord
Product shape
varies in some
countries.
Place the TV close to the
AC outlet, and keep the
power plug within reach.
Ferrite Core
Cable clamp
Cable tie
For LC-26SA1E, LC-26SV1E
LC-32SA1E_GB_a
06.7.25, 11:27 AM
3
4
Quick guide
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any
chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
30
°
30
°
Remote control sensor
5 m
1
Hold in the tab on the battery cover and pull the
cover towards the direction of the arrow.
2
Insert two supplied “AA” size batteries.
• Place batteries with their terminals corresponding
to the (e) and (f) indications in the battery
compartment.
3
Insert the smaller tab of the battery cover into the
opening (1), and press down on the cover until
it clicks in place (2).
Inserting the batteries
Before using the TV for the first time, insert two “AA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AA” size batteries.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote
control unit and sensor may prevent proper operation.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight. The
heat may cause deformation of the unit.
• The remote control unit may not work properly if the remote control sensor
of the TV is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.
1
2
LC-32SA1E_GB_a
06.7.25, 11:27 AM
4
5
Remote control unit
Quick guide
Selectable items
NICAM STEREO, MONO
NICAM CH A, NICAM CH B,
NICAM CH AB, MONO
NICAM MONO, MONO
Signal
Stereo
Bilingual
Monaural
Selectable items
STEREO, MONO
CH A, CH B, CH AB
MONO
Signal
Stereo
Bilingual
Monaural
NOTE
• When no signal is input, the sound mode will display “MONO”.
 3 (Freeze/Hold)
(See page 20.)
B (Standby/On)
Enter standby mode or turn on the
power.
(See page 7.)
[ (Subtitle for Teletext)
(See page 20.)
END
Exit the menu screen.
i (k/l) (Volume)
i (k) Increase the volume.
i (l) Decrease the volume.
0–9
Set the channel in TV mode.
Set the page in Teletext mode.
A (Flashback)
Press to return to the previous
image in normal viewing mode.
2 (Sound mode)
Select the sound multiplex mode.
(See below.)
SURROUND
Switch the surround effects on and off.
(Subpage)
(See page 20.)
SLEEP
Set the sleep timer on (in units of 30 min.
up to max. 2 hr. 30 min.) and off.
k (Reveal hidden Teletext)
(See page 20.)
p (Display information)
(See page 20.)
RETURN
Return to the previous menu screen.
e (Mute)
Switch the sound on and off.
b (INPUT SOURCE)
Select an input source.
(TV, EXT1, EXT2, EXT3, EXT4, EXT5)
(See page 8.)
f (WIDE MODE)
Select the wide mode.
(See page 19.)
Set the area of magnification in Teletext
mode. (See page 20.)
MENU
Display the MENU screen.
(See page 10.)
P (r/s)
TV: Select the channel.
External: Switch to TV input mode.
Teletext: Move to the next/previous page.
OK
Execute a command within the menu
screen.
Display the programme list. (Except
external input.)
(See page 7.)
a/b/c/d (Cursor)
Select a desired item on the setting
screen.
Colour (Red/Green/Yellow/Blue)
(See page 20.)
m (Teletext)
(See page 20.)
NICAM TV broadcasts selection
A2 TV broadcasts selection
LC-32SA1E_GB_a
06.7.25, 11:27 AM
5
6
TV (Front view)
Quick guide
TV (Rear view)
AC INPUT terminal
OPC sensor
Remote control sensor
B (Standby/On) indicator
OPC indicator
a (Power button)
b (Input button)
i (l/k)
(Volume buttons)
P (s/r)
(Programme [channel] buttons)
SLEEP indicator
EXT 2 (RGB) terminal
EXT 3 terminals
Headphone jack
EXT 1 (RGB) terminal
EXT 5 (HDMI/AUDIO)
terminals
Antenna input terminal
OUTPUT (Audio) terminals
EXT 4 terminals
RS-232C terminal
For LC-26SA1E,
LC-26SV1E
LC-32SA1E_GB_a
06.7.25, 11:27 AM
6
Page of 28
Display

Click on the first or last page to see other LC-26SA1E (serv.man3) service manuals if exist.