Sharp LC-26LE430E Service Manual ▷ View online
LC-19LE430E, LC-22LE430E, LC-26LE430E, LC-32LE430E
6
TV (Front view)
TV (Rear view)
2008-03-14
LC-19LE430E, LC-22LE430E, LC-26LE430, LC-32LE430E
7
Preparation
Mount the TV base
1.
Put the TV face down on a safe surface
that is covered by a soft and smooth cloth.
2.
Adjust the TV stand to the bottom of the TV.
Please be sure the arrow heads are facing front.
3. Fasten the screws by using a cross-head screwdriver(Not supplied).
NOTE:
To detach the TV stand, perform the steps in reverse order.
Wall mounting
TV screen
size
( Inches)
size
( Inches)
VESAcompatible
wall bracket
(millimeters)
(W x H)
wall bracket
(millimeters)
(W x H)
Screw type
19”
75 x 75 mm
Metric 4 x 10 mm
22”
100 x 100 mm
Metric 4 x 10 mm
26”
100 x 100 mm
Metric 4 x 10 mm
32”
200 x 100 mm
Metric 4 x 10 mm
NOTE
• At the time of purchasing wall bracket, please check if there is enough space between the wall bracket and TV terminals for the terminal connection.
Installation of batteries
1.
Insert two AAA batteries into Remote control. Make sure (+) and (-) are facing the proper
direction.
2.
Replace the cover
NOTE
• If the remote control will not to be used for a long time, remove the batteries to avoid remote control
damage.
CAUTION:
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries come in contact with skin can cause a rash. If you find any chemical
leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove batteries from it.
Note on disposing batteries:
The batteries provided contain no harmful materials such as cadmium, lead or mercury. Regulations concerning used batteries stipulate that batteries may
no longer be thrown out with the household rubbish. Deposit any used batteries free of charge into the designated collection containers set up at
commercial businesses.
LC-19LE430E, LC-22LE430E, LC-26LE430E, LC-32LE430E
8
Using the remote control
Use the remote control unit by pointing it towards the remote control sensor. Objects
between the remote control unit and sensor may prevent proper operation.
Display the Menu Screen
Press MENU and the menu screen displays.
Select an item by the remote control
1. Press
<>≥ to select the desired menu.
2. Press
≤ ≥ to select / adjust the item to the
desired level. The setting on screen is applied
immediately.
immediately.
3.
Press EXIT to return to the previous layer .
Exit the Menu Screen
The operation will exit the menu screen if you press EXIT before it is complete.
2008-03-14
LC-19LE430E, LC-22LE430E, LC-26LE430, LC-32LE430E
9
Appendix
troubleshooting
problem
possible Solution
No picture
1. Connect power cord correctly.
2. Turn on power.
3. Connect signal cable correctly.
4. Press any button on the LCD TV.
2. Turn on power.
3. Connect signal cable correctly.
4. Press any button on the LCD TV.
Abnormal colours
Connect signal cable correctly.
Twisted picture
1. Connect signal cable correctly.
2. Please use compatible signal.
2. Please use compatible signal.
Picture too dark
Adjust brightness and contrast.
Audio only, no images
1. Please check if input signal is connected correctly.
2. TV-RF signal must not be lower than 50dB.
2. TV-RF signal must not be lower than 50dB.
Picture only, no audio
1. Connect signal cable correctly.
2. Adjust volume to proper level.
3. Connect audio signal cable correctly.
4. TV-RF signal must not be lower than 50dB.
2. Adjust volume to proper level.
3. Connect audio signal cable correctly.
4. TV-RF signal must not be lower than 50dB.
Cannot use remote control
1. Please change battery.
2. Turn off power for 10 seconds; and then restart power.
2. Turn off power for 10 seconds; and then restart power.
Cannot receive sufficient channels
through antenna
through antenna
Please use the Channel Scan function to increase the number of channels not included in memory.
No colour
Please adjust the colour setup.
Blinking picture accompanied by ghost
image
image
1. Check the connection of antenna/signal cable.
2. Check if channel is in play mode.
3. Press signal source and change input mode.
2. Check if channel is in play mode.
3. Press signal source and change input mode.
Broken lines or segments
Adjust antenna.
Keep the TV away from noise sources, such as automobiles, neon lights, and hair dryers.
Keep the TV away from noise sources, such as automobiles, neon lights, and hair dryers.
Certain TV channels are blocked(Hope to
acquire some channels)
acquire some channels)
Please use the Update Scan method to add the channels not included in memory.
Overlapping images or ghost images
Please use multi-directional outdoor antenna.(If your TV is subject to the influence of nearby
mountains or buildings).
mountains or buildings).
Cannot use a function
If the item you choose turns gray, that item cannot be selected.
Cannot receive programmes
Please use the Update Scan method to add the channels not included in memory.
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. This
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. This
is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
• Storage temperature: +5°C to +35°C.
Information on the software license for this product
Software composition
The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third parties.
Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were developed or written by SHARP are
owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely
distributed software and software components whose copyrights are held by third parties. These include software components covered by a GNU
General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license Agreement.
owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely
distributed software and software components whose copyrights are held by third parties. These include software components covered by a GNU
General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license Agreement.
Acknowledgements
The following open source software components are included in this product:
•linuxkernel•modutils•glibc•zlib•libpng
•linuxkernel•modutils•glibc•zlib•libpng
Click on the first or last page to see other LC-26LE430E service manuals if exist.