Sharp LC-22LE510K (serv.man2) Service Manual ▷ View online
17
LC-19LE510
LC-22LE510
LC-24LE510
Operation Manual (Continued)
English - 13 -
Connecting the LCD TV to a PC
For displaying your computer’s screen image on your
LCD TV, you can connect your computer to the TV set.
Power off both computer and display before making
any connections. Use 15-pin D-sub display cable to
connect a PC to the LCD TV. When the connection
is made, switch to PC source. See “Input selection”
section. Set the resolution that suits your viewing
requirements. Resolution information can be found
in the appendix parts
.
PC Input
(back)
Side AV Input
PC VGA Cable
(Not supplied)
(Not supplied)
PC Audio Cable
(Not supplied)
Side Audio/Video
Connection Cable
(Supplied)
Or
SIDE A
V
Using Side AV Connectors
You can connect a range of optional equipment to your
LCD TV using side connectors of the TV.
For connecting a camcorder or camera , you should
•
use
AV socket (side). To do this, you must use the
supplied
video/audio connection cable. First, plug
single jack of the cable to the TV’s
AV IN socket
(side). Afterwards, insert your camera cable’s (not
supplied) connectors into the plural part of the
video/
audio connection cable. Colours of the connected
jacks should match. See illustration below.
Afterwards, you should switch to
Afterwards, you should switch to
•
Side AV source. See
the section Input selection in the following sections
for more information.
Camera
AV Connection
Cable (supplied)
AV Cable
(not supplied)
Headphone
SIDE
AV
To listen the TV sound from headphones, you
•
should connect headphones to your TV by using the
HEADPHONE jack as illustrated above..
HEADPHONE jack as illustrated above..
Remote Control Handset
Inserting Batteries
Remove the battery cover located on the back of
•
the handset by gently pulling backwards from the
indicated part.
Insert two
Insert two
•
AAA/R3 or equivalent type batteries
inside. Observe the correct polarity (+/-) when
inserting batteries and replace the battery cover.
Note: Remove the battery from remote control
handset when it is not to be used for a long period.
Otherwise it can be damaged due to any leakage of
batteries. Remote range is approximately 7m/23ft.
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC 50 Hz.
•
Then the standby LED lights up.(The led will blink
during the standby On/Off)
To switch on the TV from standby mode either:
To switch on the TV from standby mode either:
•
Press the “
•
” button, CH / CH or a numeric
button on the remote control.
Press the “
Press the “
•
” button,
- or + button on the TV. The
TV will then switch on.
Note: If you switch on your TV via CH / CH buttons
on the remote control or on the TV set, the programme
that you were watching last will be reselected.
By either method the TV will switch on.
By either method the TV will switch on.
To Switch the TV Off
Press the “
•
” button on the remote control or press
the “ ” switch on the TV, so the TV will switch to
standby mode.
To power down the TV completely, unplug the
To power down the TV completely, unplug the
•
power cord from the mains socket.
Note: When the TV is switched to standby mode,
standby LED can blink to indicate that features such
as Standby Search, Over Air Download or Timer is
active.
A01_MB60_[GB]_1910UK_IDTV_TC_PVR_BRONZE17_19942LED_YPBPR_10072629_5018xxxx.indd 13
12.05.2011 17:49:31
18
LC-19LE510
LC-22LE510
LC-24LE510
DIMENSIONS
LC-19LE510E/K Models
English - 38 -
Dimensional Drawings
A01_MB60_[GB]_1910UK_IDTV_TC_PVR_BRONZE17_19942LED_YPBPR_10072629_5018xxxx.indd 38
12.05.2011 17:49:43
English - 37 -
Speci cations
TV BROADCASTING
PAL/SECAM B/G D/K K’ I/I’ L/L’
RECEIVING CHANNELS
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
NUMBER OF PRESET CHANNELS
1000
CHANNEL INDICATOR
On Screen Display
RF AERIAL INPUT
75 Ohm (unbalanced)
OPERATING VOLTAGE
220-240V AC, 50Hz.
AUDIO
German + Nicam Stereo
AUDIO OUTPUT POWER (W
PAL/SECAM B/G D/K K’ I/I’ L/L’
RECEIVING CHANNELS
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
NUMBER OF PRESET CHANNELS
1000
CHANNEL INDICATOR
On Screen Display
RF AERIAL INPUT
75 Ohm (unbalanced)
OPERATING VOLTAGE
220-240V AC, 50Hz.
AUDIO
German + Nicam Stereo
AUDIO OUTPUT POWER (W
RMS.
) (10% THD)
2 x 2,5
POWER CONSUMPTION (W)
45 W (max)
< 0,5 W (Standby)
PANEL
16:9 display, 19” Screen Size
DIMENSIONS (mm)
DxLxH (With foot): 149 x 467 x 339
Weight (Kg): 3,35
DxLxH (Without foot): 35 x 467 x 314
Weight (Kg): 3,10
POWER CONSUMPTION (W)
45 W (max)
< 0,5 W (Standby)
PANEL
16:9 display, 19” Screen Size
DIMENSIONS (mm)
DxLxH (With foot): 149 x 467 x 339
Weight (Kg): 3,35
DxLxH (Without foot): 35 x 467 x 314
Weight (Kg): 3,10
Digital
Reception
MHEG-5 ENGINE compliant with ISO/IEC 13522-5 UK engine Pro le 1
for UK
Object carousel support compliant with ISO/IEC 135818-6 and UK DTT pro le
Frequency range: 474-850 MHz for UK models
170-862 MHz for EU models
Transmission standard: DVB-T. MPEG-2, MPEG-4
Demodulation: COFDM with 2K/8K FFT mode
FEC: all DVB modes
Video: MP@ML, PAL, 4:3/16:9
Audio: MPEG Layer I&II 32/44.148kHz.
Digital Reception (DVB-C)
Transmission Standards:
DVB-C, MPEG2, DVB-C, MPEG4
i. DEMODULATION
-Symbolrate: 4.0 Msymbols/s to 7.2 Msymbols/s
- Modulation: 16-QAM , 32-QAM ,64-QAM, 128-QAM
DVB-C, MPEG2, DVB-C, MPEG4
i. DEMODULATION
-Symbolrate: 4.0 Msymbols/s to 7.2 Msymbols/s
- Modulation: 16-QAM , 32-QAM ,64-QAM, 128-QAM
and 256-QAM
ii. VIDEO
- All MPEG2 MP@ML formats with up-conversion and
ii. VIDEO
- All MPEG2 MP@ML formats with up-conversion and
ltering to CCIR601 format.
-CVBS analogue output
iii. AUDIO
-All MPEG1 Layer 1 and 2 modes
-Sampling frequencies supported are 32, 44.1 & 48
-CVBS analogue output
iii. AUDIO
-All MPEG1 Layer 1 and 2 modes
-Sampling frequencies supported are 32, 44.1 & 48
kHz
A01_MB60_[GB]_1910UK_IDTV_TC_PVR_BRONZE17_19942LED_YPBPR_10072629_5018xxxx.indd 37
12.05.2011 17:49:43
19
LC-19LE510
LC-22LE510
LC-24LE510
LC-22LE510E/K Models
English - 37 -
Speci cations
TV BROADCASTING
PAL/SECAM B/G D/K K’ I/I’ L/L’
RECEIVING CHANNELS
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
NUMBER OF PRESET CHANNELS
1000
CHANNEL INDICATOR
On Screen Display
RF AERIAL INPUT
75 Ohm (unbalanced)
OPERATING VOLTAGE
220-240V AC, 50Hz.
AUDIO
German + Nicam Stereo
AUDIO OUTPUT POWER (W
PAL/SECAM B/G D/K K’ I/I’ L/L’
RECEIVING CHANNELS
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
NUMBER OF PRESET CHANNELS
1000
CHANNEL INDICATOR
On Screen Display
RF AERIAL INPUT
75 Ohm (unbalanced)
OPERATING VOLTAGE
220-240V AC, 50Hz.
AUDIO
German + Nicam Stereo
AUDIO OUTPUT POWER (W
RMS.
) (10% THD)
2 x 2,5
POWER CONSUMPTION (W)
45 W (max)
< 0,5 W (Standby)
PANEL
16:9 display, 22” (55 cm) Screen Size
DIMENSIONS (mm)
DxLxH (With foot): 149 x 534,6 x 377,4
Weight (Kg): 4,35
DxLxH (Without foot): 35 x 534,6 x 352,4
Weight (Kg): 4,10
POWER CONSUMPTION (W)
45 W (max)
< 0,5 W (Standby)
PANEL
16:9 display, 22” (55 cm) Screen Size
DIMENSIONS (mm)
DxLxH (With foot): 149 x 534,6 x 377,4
Weight (Kg): 4,35
DxLxH (Without foot): 35 x 534,6 x 352,4
Weight (Kg): 4,10
Digital
Reception
MHEG-5 ENGINE compliant with ISO/IEC 13522-5 UK engine Pro le 1
for UK
Object carousel support compliant with ISO/IEC 135818-6 and UK DTT pro le
Frequency range: 474-850 MHz for UK models
170-862 MHz for EU models
Transmission standard: DVB-T. MPEG-2, MPEG-4
Demodulation: COFDM with 2K/8K FFT mode
FEC: all DVB modes
Video: MP@ML, PAL, 4:3/16:9
Audio: MPEG Layer I&II 32/44.148kHz.
Digital Reception (DVB-C)
Transmission Standards:
DVB-C, MPEG2, DVB-C, MPEG4
i. DEMODULATION
-Symbolrate: 4.0 Msymbols/s to 7.2 Msymbols/s
- Modulation: 16-QAM , 32-QAM ,64-QAM, 128-QAM
DVB-C, MPEG2, DVB-C, MPEG4
i. DEMODULATION
-Symbolrate: 4.0 Msymbols/s to 7.2 Msymbols/s
- Modulation: 16-QAM , 32-QAM ,64-QAM, 128-QAM
and 256-QAM
ii. VIDEO
- All MPEG2 MP@ML formats with up-conversion and
ii. VIDEO
- All MPEG2 MP@ML formats with up-conversion and
ltering to CCIR601 format.
-CVBS analogue output
iii. AUDIO
-All MPEG1 Layer 1 and 2 modes
-Sampling frequencies supported are 32, 44.1 & 48
-CVBS analogue output
iii. AUDIO
-All MPEG1 Layer 1 and 2 modes
-Sampling frequencies supported are 32, 44.1 & 48
kHz
A01_MB60_[GB]_1910UK_IDTV_TC_PVR_BRONZE17_22942LED_YPBPR_ROCKER_10072631_50186839.indd 37
28.06.2011 14:16:18
English - 38 -
Dimensional Drawings
A01_MB60_[GB]_1910UK_IDTV_TC_PVR_BRONZE17_22942LED_YPBPR_ROCKER_10072631_50186839.indd 38
28.06.2011 14:16:18
20
LC-19LE510
LC-22LE510
LC-24LE510
LC-24LE510E/K Models
DIMENSIONS
English - 38 -
Dimensional Drawings
A01_MB60_[GB]_1910UK_IDTV_TC_PVR_NICKEL16_24942LED_YPBPR_ROCKER_10072637_5018xxxx.indd 38
06.05.2011 15:34:36
English - 37 -
Speci cations
TV BROADCASTING
PAL/SECAM B/G D/K K’ I/I’ L/L’
RECEIVING CHANNELS
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
NUMBER OF PRESET CHANNELS
1000
CHANNEL INDICATOR
On Screen Display
RF AERIAL INPUT
75 Ohm (unbalanced)
OPERATING VOLTAGE
220-240V AC, 50Hz.
AUDIO
German + Nicam Stereo
AUDIO OUTPUT POWER (W
PAL/SECAM B/G D/K K’ I/I’ L/L’
RECEIVING CHANNELS
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
NUMBER OF PRESET CHANNELS
1000
CHANNEL INDICATOR
On Screen Display
RF AERIAL INPUT
75 Ohm (unbalanced)
OPERATING VOLTAGE
220-240V AC, 50Hz.
AUDIO
German + Nicam Stereo
AUDIO OUTPUT POWER (W
RMS.
) (10% THD)
2 x 2,5
POWER CONSUMPTION (W)
50 W (max)
< 0,5 W (Standby)
PANEL
16:9 display, 24” Screen Size
DIMENSIONS (mm)
DxLxH (With foot): 149 x 580 x 405
Weight (Kg): 5,20
DxLxH (Without foot): 35,5 x 580 x 380
Weight (Kg): 4,80
POWER CONSUMPTION (W)
50 W (max)
< 0,5 W (Standby)
PANEL
16:9 display, 24” Screen Size
DIMENSIONS (mm)
DxLxH (With foot): 149 x 580 x 405
Weight (Kg): 5,20
DxLxH (Without foot): 35,5 x 580 x 380
Weight (Kg): 4,80
Digital
Reception
MHEG-5 ENGINE compliant with ISO/IEC 13522-5 UK engine Pro le 1
for UK
Object carousel support compliant with ISO/IEC 135818-6 and UK DTT pro le
Frequency range: 474-850 MHz for UK models
170-862 MHz for EU models
Transmission standard: DVB-T. MPEG-2, MPEG-4
Demodulation: COFDM with 2K/8K FFT mode
FEC: all DVB modes
Video: MP@ML, PAL, 4:3/16:9
Audio: MPEG Layer I&II 32/44.148kHz.
Digital Reception (DVB-C)
Transmission Standards:
DVB-C, MPEG2, DVB-C, MPEG4
i. DEMODULATION
-Symbolrate: 4.0 Msymbols/s to 7.2 Msymbols/s
- Modulation: 16-QAM , 32-QAM ,64-QAM, 128-QAM
DVB-C, MPEG2, DVB-C, MPEG4
i. DEMODULATION
-Symbolrate: 4.0 Msymbols/s to 7.2 Msymbols/s
- Modulation: 16-QAM , 32-QAM ,64-QAM, 128-QAM
and 256-QAM
ii. VIDEO
- All MPEG2 MP@ML formats with up-conversion and
ii. VIDEO
- All MPEG2 MP@ML formats with up-conversion and
ltering to CCIR601 format.
-CVBS analogue output
iii. AUDIO
-All MPEG1 Layer 1 and 2 modes
-Sampling frequencies supported are 32, 44.1 & 48
-CVBS analogue output
iii. AUDIO
-All MPEG1 Layer 1 and 2 modes
-Sampling frequencies supported are 32, 44.1 & 48
kHz
A01_MB60_[GB]_1910UK_IDTV_TC_PVR_NICKEL16_24942LED_YPBPR_ROCKER_10072637_5018xxxx.indd 37
06.05.2011 15:34:36
Click on the first or last page to see other LC-22LE510K (serv.man2) service manuals if exist.