DOWNLOAD Sharp LC-22DS240K (serv.man2) Service Manual ↓ Size: 2.67 MB | Pages: 3 in PDF or view online for FREE

5

4

Important note: Ensure that the aerial is connected before switching on the 
TV for the first time installation.
Note:  Do  not  turn  off  the  TV  while  initializing  first  time  installation.
When the TV is turned on for the first time, the menu for the language selection 
appears  on  the  screen.  The  message  “Welcome    please  select  your 
language!”  is  displayed  in  all  language  options  sequentially  in  the  menu 
screen.
By pressing    or    buttons highlight the language you want to set and press 
“OK”.  After  selecting  the  language,  “Welcome!”  screen  will  be  displayed, 
requiring you to set 

Use navigation buttons to set the required options. When finished, press OK 
button on the remote control and the following message will be displayed on 
the screen:

Select YES by using the Left or Right button and and press OK button to start 
search. Afterwards, the following OSD will be displayed on the screen and the 
television will search for broadcasts.

Country, Search Type, Teletext Language, Scan Encrypted 

and Store Mode  options:  

3

2

1

Insert two AAA/R3 or 
equivalent type batteries 
inside. Observe the correct 
polarity (+/-) when inserting 
batteries and replace the 
battery cover.

Auto TV Off:
Important
By default your TV will switch off after 4 hours of remote 
inactivity, the power down time can be changed in hourly 
increments or set to “Off” to disable this feature. 
Using the remote control:
1. Press “Menu”
2. Scroll to “Settings” (Green Icon) and press “OK”
3. Scroll down to “Other Settings” and press “OK”
4. Scroll down to “Auto TV OFF” and scroll right or left until 
“Off” is selected
5. Press “Menu”

If you are located at a TV regional border or are able to receive broadcasts from
more than one transmitter the “Choose Region” OSD will be displayed after the
digital channels have been scanned. Please select your local region and
transmitter for best results and press OK.

After all the available stations have been stored a channel list will be shown
based on the broadcaster LCN  (Logical Channel Number) press OK to accept
this channel order and again to start viewing  or you can use the Edit functions
To change the order or delete unwanted channels.

To select the HDMI input, press the “SOURCE” button on the remote 
control. Each time it is pressed the on-screen menu confirms your 
selection. 

When  the  TV  set  is  turned  on,  switch  to  DVD  input  by  using  the 
SOURCE  button  on  the  remote  control.  Press  play  on  the  remote 
control, or directly press play button on the side panel. 

Sound settings:
Important
If the default audio settings are not to your liking please adjust to your 
preference  via  the  “Sound”  menu,  please  refer  to  the  operation 
manual for all available features.
Using the remote control:
1. Press “Menu”
2. Scroll to “Sound” (Cyan Speaker Icon) and press “OK”
3. Scroll down to “Equaliser” and press “OK”
4. Select inbuilt Preset  or “User” to set custom levels.

6

7

1. Switch the “  ” button to position “|” so the TV will switch to 

standby mode. Then the standby LED lights up.

To switch on the TV from standby mode either:
2. Press the “  ” button, 

 

   or a numeric button on the 

remote control.

3. Press the “  ” or 

 button on the TV.

By either method the TV will switch on.

8

9

IMPORTANT: To record a programme, you should rst connect 
a USB memory stick to your TV while the TV is switched off. You 
should  then  switch  on  the  TV  to  enable  recording  feature. 
Otherwise, recording feature will not be available. 

You should back up your les before making any connections to 
the TV set in order to avoid any possible data loss. Note that 
manufacturer will not be responsible for any le damage or data 
loss. 

CAUTION !
•  Quickly  plugging  and  unplugging  USB  devices,  is  a  very 
hazardous operation. Especially, do not repeatedly quickly plug 
and unplug the drive. This may cause physical damage to the 
USB player and especially the USB device itself.
• Do not pull out USB module while playing or recording a le.

IMPORTANT:  The  TV  supports  only  FAT32  and  NTFS  disk 
formatting.  However,  NTFS  format  is  not  supported  for 
recording  features.  For  recording,  if  you  connect  a  USB  disk 
with NTFS format, the TV will ask you to format the content. See 
the  section,  “Format  Disk”  in  the  instruction  book  for  more 
information on disk formatting.
Note that ALL the data stored on the USB disk will be lost and 
then the disk format will be converted to FAT32 in such a case.

10

Press     (RECORD) button to start recording an event instantly while 
watching a programme. The following OSD appears on the screen:

Record OSD will then be displayed for a short time and the current 
event will be recorded. You can press       (RECORD) button on the 
remote  control  again  to  record  the  next  event  on  the  EPG.  In  this 
case, OSD will display the programmed events for recording.

Press       (STOP) button to cancel instant recording. The

Select Yes by using Left or Right and OK 

buttons to cancel instant recording.

 following 

 will be displayed. 

OSD

In the main menu, use Left or Right buttons to select Media 
Browser. Highlight Recordings Library item by using Left or 
Right button and press OK button to enter. Recordings 
Library will then be displayed.

Select a recorded item from the list (if previously recorded) by  
using Up or Down button. Press OK button to view Play 
Options. 
Select an option by using Up or Down and OK buttons.

Available playback options:
• Play from start: Plays the recording from the beginning.
• Resume: Recommences the recordings.
• Play from offset: Species a playing point.

Press 

 

(STOP) button to stop a playback and return to return 

to Recordings Library.

11

Please read the following information carefully before attaching the stand to your new Sharp Television.

!

 Before fitting the stand, ensure that the TV is unplugged from its power source.

!

 Place the Sharp Television (1) on a soft, stable and flat surface, facing down.

!

 Place the Stand (3) on the stand mounting pattern on the rear side of the TV. 

  Ensure the Stand (3) is placed correctly and that you can see the screw holes on 
the back of the Sharp Television.

!

 Place the Stand Cover (2) on the Stand (3).

!

 Ensure the Stand Cover (3) is placed correctly and that you can see the screw 

holes on the back of the Sharp Television.

!

 DO NOT insert the screws before placing the plastic molding.

!

 Insert the four screws provided and tighten them gently until the stand is properly 

fitted.

Please read the following information carefully before detaching the stand of your Sharp Television. 

!

 Before detaching the stand, ensure that the TV is unplugged from its power source.

!

 Place the Sharp Television on a soft, stable and flat surface, facing down. 

!

 Unscrew gently the four screws that attach the foot assembly and remove the 

screws when they are completely unscrewed. 

!

 Remove the stand and plastic moulding gently from the panel. 

50217970