DOWNLOAD Sharp LC-20SD4E (serv.man7) Service Manual ↓ Size: 1.71 MB | Pages: 30 in PDF or view online for FREE

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical

leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any

chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.

30

°

5m

30

°

Remote control sensor

Press and slide the battery
cover to open it.

Before using the TV for the first time, insert two “AA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AA” size batteries.

Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote
control unit and sensor may prevent proper operation.

• Do not expose the remote control unit to shock.

In addition, do not expose the remote control unit to liquids, and do not
place in an area with high humidity.

• Do not install or place the remote control unit under direct sunlight. The

heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote control sensor

of the TV is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.

Insert two supplied
“AA” size batteries.

• Place batteries with their terminals corresponding

to the (e) and (f) indications in the battery
compartment.

Close the battery cover.

B (Standby/On)
Enter standby mode or turn on the
power. (See page 7.)

BACKLIGHT
Adjust the screen brightness.

TV/RADIO
DTV: Switch between RADIO and
DTV mode.

DTV/TV
Switch between analogue TV and
DTV mode.

e (Mute)
Switch the sound on and off.

0–9
Set the channel in TV and DTV mode.
Set the page in Teletext mode.

A (Flashback)
Press to return to the previous image
in normal viewing mode.

f (WIDE MODE)
DTV: Select the wide mode.
(See page 25.)

6 (Sound mode)
Select the sound multiplex mode.
(See below.)

GUIDE
DTV: To display EPG (Electronic
Programme Guide) screen.

7 (Teletext)
Select the TELETEXT mode. (all TV
image, all TEXT image, TV/TEXT
image) (See page 15.)
DTV: Select DTV data broadcasting
and TELETEXT.

EXIT
Exit the menu screen.

k (SKIP/Reveal hidden Teletext)
TV: Conceal stored channels. (See
page 15.)
TELETEXT: (See page 15.)

3 (STATUS/Hold)
TV: Display the clock and
programme infor mation, if it is
available.
TELETEXT: (See page 15.)

i (k/l) (Volume)

i (k) Increase the volume.

i (l) Decrease the volume.

P (r/s)
TV/DTV: Select the channel.
External: Switch to TV or DTV input
mode.
Teletext: Move to the next/previous
page.

b (INPUT SOURCE)
Select an input source.
(TV, EXT1, EXT2) (See page 8.)

SLEEP
Set the sleep timer in units of 30 min.
up to max. 2 hr.

p (Display information)
Display various information; channel
number, sleep timer, etc.
(See pages 23 and 24.)

DTV MENU
DTV: Display DTV Menu screen.

MENU
Display the MENU screen.
(See page 9.)

a/b/c/d (Cursor)
Select a desired item on the setting
screen.

ENTER
Execute a command within the menu
screen.
DTV: Display the Channel list.

v (Top/Bottom/Full)
Set the area of magnification in
Teletext mode. (See page 15.)

1 (Subpage)
(See page 15.)

[ (Subtitle for Teletext)
TELETEXT: To turn the subtitles on
and off. (See page 15.)
DTV: Display the subtitle selection
screen. (See page 25.)

Colour (Red/Green/Yellow/Blue)
TELETEXT: Select a page.
(See page 15.)
DTV: The coloured buttons are used
to select correspondingly to the
coloured items in the menu screen.

Mono, Nicam Stereo

Mono, Nicam Sound1, Nicam
Sound2

Mono

Mono, Stereo

Mono, Sound1, Sound2

Mono

• When no signal is input, the sound mode will display “

Mono

”.

E

 Using 6 on the remote control unit

Press 6 to open the multi audio screen. (See page 25.)
Analogue TV mode:
Each time you press 6, the mode switches as illustrated in the following tables.

C.I. 

I

EXT1

(RGB)

AUDIO

OUT

VIDEO

S-VIDEO

AUDIO

L

L

R

R

EXT2

AC INPUT

220-240V

(MONO)

AC INPUT terminal

Remote control sensor

B (Standby/On) indicator

Headphone jack

a (Power button)

b (Input button)/ENTER

i (l/k) (Volume buttons)

Cursor (c/d)

P (s/r)

(Programme [channel] buttons)

Cursor (a/b)

EXT2 terminals

EXT1 (RGB) terminal

Antenna input terminal

(DVB-T 5V=/80 mA)

OUTPUT (Audio) terminals

COMMON INTERFACE slot

Press a on the TV.

• The B indicator on the TV changes from red to green.

• If you are not going to use this TV for a long period of

time, be sure to remove the AC cord from the power outlet.

• In DTV input mode, if the power is turned off immediately

after a setting change from the menu screen, the new
setting or channel information may not be memorised.

When the TV powers on for the first time after purchase,
the initial auto installation is invoked. You can
automatically set language, country and channels in
successive operations.

• The initial auto installation functions only once. If the initial

auto installation is not completed, (ex: When menu screen
disappeared by not operating for a few minutes, when
the power shut down, etc.), try First Installation from the
Setup menu. (See page 13.)

• The initial auto installation can be stopped by pressing

MENU or EXIT.

Setting the on-screen display language

1 Press a/b/c/d to select the desired language

listed from “First installation(Language)”.

2 Press ENTER to enter the setting.

Setting your country or area

1 Press  a/b/c/d to select your country or area

listed from “First installation(Country)”.

2 Press ENTER to enter the setting.

Setting the Automatic search

1 Press a/b to select the colour system.
2 Press ENTER to enter the setting.
• The programme auto search starts at the same time.

You do not need to do anything during the auto search.

The setup menu disappears and you can watch the
programme on channel 1.

Press B on the remote control unit when the TV is
on.

• The TV enters standby mode and the image on the screen

disappears.

• The B indicator on the TV changes from green to red.
• You can turn the TV on by pressing B on the remote

control unit from standby mode.

• Weak electric power is still consumed even when B is

turned off.

• To completely turn off the TV, press a on the TV.

Off

Red

Green

Orange

Power off

The TV is in standby mode.

The TV is on.

The TV screen is off and a Timer event
has begun.

Although it only displays the tuning of the analogue
channel, it is actually tuning the digital channels at
the same time.

• Both analogue and digital channels are scanned at the

same time during “Automatic search” of the “First
installation”, and digital channel tuning is faster than
analogue tuning. If you want to operate the digital mode
first, press EXIT and then press DTV/TV.

• You can select a language from the Setup menu. Select

from 13 languages. (English, Spanish, German, French,
Italian, Swedish, Dutch, Russian, Portuguese, Turkish,
Greek, Finnish, Polish)

• You can select a country from the Setup menu. Select

from 13 countries. (United Kingdom, Spain, Germany,
France, Italy, Sweden, Netherlands, Russia, Portugal,
Turkey, Greece, Finland, Poland)
* If on the “First Installation(country)” screen “United

Kingdom” is selected, “Move To” cannot be used in U.K.

• If you want to reconfigure the country setting, for instance

after moving to another country, conduct “First installation”
from the Analogue Menu again.

• After “Auto Scan” is complete, carrier names are sorted

in the same order of the “Channel Sort Table List (TV,
Radio)”.

• Sorting is accomplished by checking whether the service

name correspond to the “Received Service Name” of the
“Channel Sort Table List”.

• Received carrier names are not changed to match the

“Short Service Name”.

• The channel position moves up, if the service is not found

after the “Auto Scan” is finished.

• A carrier that is not in the “Channel Sort Table List” will be

positioned at the bottom of the sorted list.

• If the same service name is duplicated, the tuner selects

the stronger signal, sorts it and places it in the list. The
weaker signal listing is placed at the bottom of the list.

• TV and Radio presetting is done separately so LCN

numbers are not duplicated between the two.