DOWNLOAD Sharp LC-19D1EWH (serv.man6) Service Manual ↓ Size: 6.38 MB | Pages: 28 in PDF or view online for FREE

LC-19D1E/S-BK/WH

5 – 7

23

VCCP1N

 -

ch1 Power supply terminal of the minus side power amplifier output   (Rch-)

24

N.C.

 -

No connection

25

BSP1N

I

ch1 The minus side boost strap terminal  2N (Rch-)

26

WARNING

O

Warning output terminal . It is a terminal which tells warning of operation.

27

ERROR

O

Error output terminal .    It is a terminal which tells an error of operation.

28

MUTEX

I

Audio mute control terminal.  (H: mute OFF  L: mute ON)

29

N.C.

 -

No connection

30

N.C.

 -

No connection

31

OSC

I/O

Sampling clock signal input-and-output terminal.

32

MS

I

master slave change terminal    (H: slave operation  L: master operation)

33

ROSC

I

Sampling clock frequency setting terminal for Insides PWM.    
It can usually use it by opening..  

34

TM

I

Audio mute time constant setting terminal

35

VHOLD

I

The detection voltage setting terminal for a power supply instant cutting detection function

36

BSP2N

I

ch2 Minus side boost strap terminal  2N (Lch-)

37

N.C.

 -

No connection

38

VCCP2N

 -

ch2 Power supply terminal of the minus side power amplifier output  (Lch-)

39

VCCP2N

 -

ch2 Power supply terminal of the minus side power amplifier output  (Lch-)

40

OUT2N

O

ch2 Minus side PWM signal output terminal  (Lch-)

41

OUT2N

O

ch2 Minus side PWM signal output terminal  (Lch-)

42

GNDP2

 -

ch2 Ground terminal of a power amplifier output.  (Lch)

43

GNDP2

 -

ch2 Ground terminal of a power amplifier output.  (Lch)

44

OUT2P

O

ch2 Plus side PWM signal output terminal  (Lch+)

45

OUT2P

O

ch2 Plus side PWM signal output terminal  (Lch+)

46

VCCP2P

 -

ch2 Power supply terminal of the plus side power amplifier output  (Lch+)

47

VCCP2P

 -

ch2 Power supply terminal of the plus side power amplifier output  (Lch+)

48

N.C.

 -

No connection

LC-19D1E/S-BK/WH

5 – 8

LC-19D1E/S-BK/WH

5 – 9

A/V SWITCH (12C BUS)

1

V1-V

Video input terminal

3

V1-Y

(Composite or Y)

7

V2-V

*Sync chip clamp

9

V2-Y

13

V3-V

I

16

STV-V

19

YIN2

32

YIN1

41

MTV-V

2

V1-L

Audio input terminal

4

V1-R

8

V2-L

10

V2-R

14

V3-L

I

15

V3-R

17

STV-L

18

STV-R

40

MTV-R

42

MTV-L

5

V1-C

Video input terminal

11

V2-C

I

(Croma)

21

CIN2

31

CIN1

6

S1

I

Distinction 3-effects input terminal

12

S2

DC Detect

20

ADR

I

Sleve address select

30

MUTE

Audio Mute terminal

27

GND

-

Ground.

22

VOUT2

O

Composite video out

35

VOUT1

23

ROUT2

Audio out terminal

25

LOUT2

O

33

ROUT1

34

LOUT1

24

COUT2

S-Video out terminal

26

YOUT2

O

37

YOUT1

39

COUT1

28

SDA

I/O

Data input from I2C

29

SCL

I

CLK input from I2C

36

BIAS

I

Internal bias terminal

38

VCC

-

Power Supply.

LC-19D1E/S-BK/WH

5 – 10

RS232C-DRIVER/RECEIVER

1

EN

I

Receiver Enable Control . Drive low for normal operation. Drive high to force the receiver outputs (R_OUT) into 
a high-impedance state.

2

C1+

 -

Positive terminal of the voltage doubler Charge-Pump Capacitor

3

V+

 -

 +5.5V generated by the charge pump

4

C1-

 -

Negative terminal of the voltage doubler Charge-Pump Capacitor

5

C2+

 -

Positive terminal of inverting Charge-Pump Capacitor

6

C2-

 -

Negative terminal of inverting Charge-Pump Capacitor

7

V-

 -

 -5.5V generated by the charge pump

8

R_IN

I

RS-232 Receiver Inputs

9

R_OUT

O

TTL/CMOS Receiver Outputs

10

INVALID

I

Output of the Valid Signal Detector. INVALID is enabled high if a valid RS-232 level is present on any receiver 
input.

11

T_IN

I

TTL/CMOS Transmitter Inputs

12

FORCEON

I

Drive high to override automatic circuitry keeping transmitters and charge pump on (FORCEOFF must be high)

13

T_OUT

O

RS-232 Transmitter Outputs

14

GND

 -

Ground

15

VCC

 -

 +3.0V to +5.5V Supply Voltage

16

FORCEOFF

I

Force-Off Input, active low. Drive low to shut down transmitters, receivers (MAX3243E, except R2OUTB), and 
on-board charge pump . This overrides all automatic circuitry and FORCE ON