DOWNLOAD Sharp LC-19D1EWH (serv.man10) Service Manual ↓ Size: 1.2 MB | Pages: 32 in PDF or view online for FREE

Model
LC-19D1EWH (serv.man10)
Pages
32
Size
1.2 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
TV / LCD
File
lc-19d1ewh-sm10.pdf
Date

Sharp LC-19D1EWH (serv.man10) User Manual / Operation Manual ▷ View online

4
Quick guide
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any
chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
1
Hold in the tab on the battery cover and pull the
cover towards the direction of the arrow.
2
Insert two supplied “AA” size batteries.
• Place batteries with their terminals corresponding
to the (e) and (f) indications in the battery
compartment.
3
Insert the smaller tab of the battery cover into the
opening (1), and press down on the cover until
it clicks in place (2).
Inserting the batteries
Before using the TV for the first time, insert two “AA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AA” size batteries.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote
control unit and sensor may prevent proper operation.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight. The
heat may cause deformation of the unit.
• The remote control unit may not work properly if the remote control sensor
of the TV is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.
30
°
30
°
Remote control sensor
5 m
5
Remote control unit
Quick guide
Selectable items
NICAM STEREO, MONO
NICAM CH A, NICAM CH B,
NICAM CH AB, MONO
NICAM MONO, MONO
Signal
Stereo
Bilingual
Monaural
Selectable items
STEREO, MONO
CH A, CH B, CH AB
MONO
Signal
Stereo
Bilingual
Monaural
• Using K on the remote control unit
DTV mode:
Press K to open the multi audio screen. (See page 24.)
Analogue TV  mode:
Each time you press K, the mode switches as illustrated in the following
tables.
* The volume can be individually set for the speaker and headphones output for
each input (TV, DTV, EXT 1, EXT 2, EXT 3, EXT 4, EXT 5).
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
15
17
19
18
20
21
22
23
24
25
26
27
28
29
30
1
B (Standby/On)
Enter standby mode or turn on the
power.
2
p (Display information)
(See pages 23 and 24.)
3
DTV MENU
DTV: Display DTV Menu screen.
4
0–9
Set the channel in TV mode.
Set the page in Teletext mode.
5
A (Flashback)
Press to return to the previous
selected channel or external input
mode.
6
DTV
Press to access DTV mode while
watching other input sources, and
vice versa.
7
 (WIDE MODE)
Select the wide mode. (See page
17.)
8
Z (Freeze)
Freeze a motion picture on the
screen.
9
a/b/c/d (Cursor)
Select a desired item on the
setting screen.
OK
Execute a command within the
menu screen.
TV/DTV: Display the programme
list. (See pages 17 and 24.)
10
END
Exit the menu screen.
11
EPG
DTV: To display EPG (Electronic
Programme Guide) screen.
(See page 23.)
12
(Teletext)
Select the TELETEXT mode. (See
pages 18 and 24.)
DTV: Select DTV data
broadcasting and TELETEXT.
13
ESG
DTV: To display ESG (Electronic
Service Guide) screen. (See page
23.)
16
AV MODE
Select an audio and video setting.
(See page 10.)
17
e (Mute)
Switch the sound on and off.
18
K (Sound mode)
Select the sound multiplex mode.
(See below.)
19
(k/l) (Volume)*
i (k) Increase the volume.
i (l) Decrease the volume.
20
P (r/s)
TV/DTV: Select the channel.
External: Switch to TV or DTV
input mode.
Teletext: Move to the next/previous
page.
21
b
 (INPUT SOURCE)
Select an input source.
(See pages 8 and 9.)
22
RADIO
DTV: Switch between RADIO and
DTV mode.
• Due to the large variation in
transmitted volume levels in
RADIO mode, some stations
will produce distortion if the
volume level is set too high.
23
PC
Directly select the PC terminal as
an INPUT SOURCE.
24
MENU
Display the MENU screen.
25
RETURN
Return to the previous menu
screen.
26
Colour (Red/Green/Yellow/Blue)
TELETEXT: Select a page. (See
page 18.)
DTV: The coloured buttons are
used to select correspondingly to
the coloured items in the menu
screen.
27
[ (Subtitle for Teletext)
TV/External: To turn the subtitles
on and off.
DTV: Display the subtitle selection
screen. (See page 24.)
28
k (Reveal hidden Teletext)
(See page 18.)
29
(Top/Bottom/Full)
Switch the Teletext image to Top,
Bottom or Full.
30
1
 (Subpage)
(See page 18.)
When one of the 4 Nordic
countries (Sweden, Norway,
Finland, or Denmark) is
selected in the country setting
of Auto Installation, DTV
channels are 4 digits. When
another country is selected,
DTV channels are 3 digits.
14
3
 (Hold)
(See page 18.)
15
SLEEP
Set the sleep timer on (in units of
30 min. up to max. 2 hr. 30 min.)
and off.
NICAM TV broadcasts selection
A2 TV broadcasts selection
6
TV (Front/Side view)
Quick guide
TV (Rear view)
WARNING:
Make sure that the volume is turned down before
using or connecting earphones and headphones.
Listen to audio at moderate levels. Excessive
sound pressure from earphones and headphones
can cause hearing loss.
b (Input Source) button
a Power button
MENU button
Antenna input terminal
(DVB-T 5V=/80mA)
EXT 2 terminals
i (e/f) (Volume
buttons)
P (r/s) (Channel
buttons)
OPC indicator
OPC sensor
B (Standby/On)
indicator
Remote control sensor
Headphone jack
RS-232C terminal
EXT 3 (Component)
terminals
EXT 4 (HDMI/AUDIO)
terminals
EXT 1 (RGB) terminal
EXT 5 terminals
AC INPUT terminal
Regarding the headphone jack
• Use headphones with a stereo mini plug (Ø 3.5 mm).
• Be sure to unplug headphones from the jack when they
are not in use.
• The speakers do not output volume when headphones are
plugged in.
• You can set the volume to different levels for each input
source.
Round lock for Kensington
Security Standard slot
NOTE
• Only if you use an active terrestrial antenna, select “On(5V)” under “Supply Voltage”. (See page 16.)
COMMON
INTERFACE
slot
TV control panel buttons
Pr
Ps
ik
il
Remote control buttons
b
OK
a
b
d
c
Operation without a remote control unit
7
Turning on the power
When the Power of the TV is OFF (B indicator is off),
Press a on the TV.
• The B indicator on the TV changes to green.
When the TV is in Standby ( B indicator is Red),
Press B on the remote control unit.
• The B indicator on the TV changes from red to green.
NOTE
• If you are not going to use this TV for a long period of
time, be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when a is
turned off.
• In DTV input mode, if the power is turned off immediately
after a setting change from the menu screen, the new
setting or channel information may not be memorised.
Initial auto installation (Analogue)
When the TV powers on for the first time after purchase,
the initial auto installation is invoked. You can
automatically set language, country and channels in
successive operations.
You do not need to do anything during the auto search.
NOTE
• The initial auto installation functions only once. If the initial
auto installation is not completed, (ex: When menu screen
disappeared by not operating for a few minutes, when
the power shut down, etc.), try Auto Installation from the
Setup menu. (See page 12.)
• The initial auto installation stops by pressing RETURN.
Standby mode
Press B on the remote control unit.
• The TV enters standby mode and the image on the screen
disappears.
• The B indicator on the TV changes from green to red.
Turning off the power
Press a on the TV.
• The B indicator on the TV turns off.
• When the TV is turned off by a, you cannot turn on the
power by pressing B on the remote control unit.
Off
Red
Green
Display status indicator
Power off
The TV is in standby mode.
The TV is on.
The setup menu disappears and you can watch the
programme on channel 1.
Quick guide
1
Setting the on-screen display language
1 Press a/b/c/d to select the desired language
listed on the screen.
2 Press OK to enter the setting.
2
Setting the country or area
1 Press  a/b/c/d to select your country or area
listed on the screen.
2 Press OK to enter the setting.
• The programme auto search starts at the same time.
Initial auto installation (DTV)
Digital Video Broadcasting is a transmission scheme.
It is much more than a simple replacement for existing
analogue television transmission. DVB provides more
stations, clearer picture quality and other services
displayed on the screen. It also allows a range of new
features and services including subtitles and multiple
audio tracks.
To watch DTV broadcasts, follow the procedures below
to scan all available services in your area.
1
Press DTV or b to access the DTV mode.
2
Press  DTV MENU and the DTV Menu screen
displays.
3
Press c/d to select “Installation”.
4
Press a/b to select “Auto Installation”, and then
press OK.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
• See page 14 for setting PIN.
• A confirmation message displays. To start the
search, select “Yes”.
5
The TV starts scanning all available DTV and radio
services in your area.
NOTE
• The language and country settings used in this operation
are the settings you have already set while executing the
Initial auto installation (Analogue). If you want to
reconfigure the country setting, for instance after moving
to another country, conduct “Auto Installation” from the
Setup menu again.
• The services are stored according to the channel number
information embedded in the stream (if available). If the
information is not available, the services are stored
according to the order in which they were received.
If you would like to sort the order, it is possible to arrange
it as explained in page 20.
• To cancel the scan in progress, press END.
• You cannot select any DTV-related menu items unless
“Auto Installation” has been completed.
Page of 32
Display

Click on the first or last page to see other LC-19D1EWH (serv.man10) service manuals if exist.