DOWNLOAD Sharp LC-15C2E (serv.man9) Service Manual ↓ Size: 3.8 MB | Pages: 47 in PDF or view online for FREE

There are three methods below.
1) Press the “Adjustment process key” on the remote control after turning on the power.
2) Pressing both the MENU key and the TV/VIDEO key on the main body, turn on the power. Then, press the volume

DOWN key and the tuning DOWN key at the same time.

3) Turn on the power with falling either KEY4 (pin 81 of microcomputer) or KEY5 (pin 82 of microcomputer) to “L”.
[Note] For the method 3), the ROM is initialized at the same time. Therefore, 3) must be executed if IC2004 or IC2001

is changed. For 1) or 2), the main body only enters the MAIN side adjustment process.

4) Entering the TUNER side adjustment process

MENU key on the main body 

→

 Cursor UP key (remote control) 

→

 Select the position shown in the figure below and

press the M key (remote control) within 1 second. 

→

 Enters the adjustment process.

MAIN side adjustment (Press the “M” key to move the cursor and press the volume UP/DOWN key to make an
adjustment.)
• Power supply voltage adjustment (+B 5V)
• Model setting
• Inch size setting
• COMMON BIAS adjustment of LCD module
• CUTOFF adjustment

TUNER side adjustment (Press the tuning UP/DOWN key to move the cursor and press the volume UP/DOWN key to
make an adjustment.)
• Horizontal size adjustment (LCD adjustments)
• Video adjustment (other adjustments)
  Y delay
  Subcontrast
  Subcolour
  Subbrightness
  Tint offset
  AGC gain start
The TUNER side adjustment is possible. However, it is recommended to replace EAROM (I2).

Black level

Contrast

Colour

: select

M: Back
E: End

PAL/PAL60

SECAM

NTSC

y delay

7

6

RF

tint offset

0

0

sub contrast

2

2

sub colour

25

25

y delay

7

5

4

AV1

tint offset

1

1

1

AV2

sub contrast

0

2

0

sub colour

30

30

20

y delay

7

5

1

AVS

tint offset

1

1

1

sub contrast

0

0

0

sub colour

30

30

30

AGC gain start

23

3-1. +B adjustment

Page 9 of MAIN side adjustment process  +B-ADJ
Adjust the voltage of the pin 13 of P2002 to 5.0V

±

0.05V.

3-2. Model setting

Page 9 of MAIN side adjustment process  MODEL
Set to C2E.

3-3. Inch size setting

Page 9 of MAIN side adjustment process  INCH SIZE
Set to 15.

3-4. COMMON BIAS adjustment of LCD module

Page 9 of MAIN side adjustment process  COM BIAS
Input the picture of gray scale and adjust it so as to obtain the best contrast.

3-5. CUTOFF adjustment

Page 9 of MAIN side adjustment process  R CUTOFF, B CUTOFF
Adjust it so as to obtain the optimal colour balance.

4-1. Functional description

This LCD color television has a function (lamp error detection) to be turned OFF automatically for safety when
the lamp or lamp circuit is abnormal.
If the lamp or lamp circuit is abnormal, or some other errors happen, and the lamp error detection is
executed, the followings occur.

1

The main unit of television is turned OFF 5 seconds after it is turned ON. (The power LED on the front side of
TV turns from green to red.)

2

If the situation 

1

 happens 5 times sequentially, television can not be turned ON. (The power LED remains

red.)

4-2. Countermeasures
4-2-1. Check when turning OFF the lamp error detection

When television is turned OFF by the lamp error detection mentioned above, it enters the adjustment
process with the power LED red. Entering the adjustment process turns OFF the error detection and turns
ON TV.
This enables the operation check to detect errors in the lamp or lamp circuit.
Check whether "ERROR NO RESET" on line 7, page 1 of the adjustment process is 1 or more. If it is 1 or
more, it indicates the lamp error detection was executed.

4-2-2. Resetting of the lamp error count

After confirming that the lamp or lamp circuit is normal, reset the lamp error count. Select "ERROR NO
RESET" on line 5, page 1 of the adjustment process and set the number to 0 using the volume button.

 1

 + B – A D J

160

M O D E L

C2E

  I N C H   I

S   I Z E

15

N T S C

P W M

F R Q

0C0

E R R O R

N O

R E S E T

5

P M U T E

OFF

C 2 E

V E R

1 .   0  0

Reset 0

Page 1 of the adjustment process

Afterwards, perform the operation check to confirm that the lamp error detection does not function.

Check all the settings microprocessor's adjust process menu.

Do F2, F3 and F4 

function?

Are T701's secondary 

outputs, +38V, +16V, +9V, 

+5V and -8V normal?

Remove F2, F3 and F4 

and check the load side.

Is there short-circuiting?

Is there short-circuiting of 

T701 primary side periphery, 

Q751, Q753 and P901.

Replace F2, F3 and F4.

Check P901 and 

connection cable.

Is T701's primary oscillator 

waveform normal?

Check T701's secondary 

load.

Does F1 function?

Is the pin 34 of IC1201 in 

the "H" state?

Is the Q7603 short-circuiting?

Is there short-circuiting of 

T5701 and T5702 primary 

side periphery, Q751~Q753.

Replace the fluorecent lamp 

with new one and check 

again.

Check the OFL1 line, IC1201 

and their peripheral parts.

Check Q7603 and their 

peripheral parts.

Check T5701, T5702, 

Q5701~Q5703 and 

connection cable.