DOWNLOAD Sharp 66GF-63 Service Manual ↓ Size: 784.01 KB | Pages: 2 in PDF or view online for FREE

COLOUR TELEVISION

●  

Fitting the batteries into the remote control

●

 Connecting the aerial cable

●

 Tuning the TV channels

Using this installation
guide should enable you
to set up your TV in less
than 15 minutes - - -
- - - Please refer to your
operation manual for
more tips and advice

PRINTED ON RECYCLED PAPER

PRINTED IN SPAIN
TINS-6895BMN1
03/01

Sharp House, Thorp Road, Newton Heath,

Manchester M40 5BE

Refer to the Operation Manual for:

Channel selection .................................. P. 10
Picture adjustments............................... P. 11
Audio adjustments.................................. P. 15
Timer settings (ON/OFF Timer)............... P. 19
Child lock................................................ P. 21
Menu structures...................................... P. 23
Teletext mode......................................... P. 24

1 Select a well-ventilated location.

2  Avoid exposing this set to direct sunlight,

dust, heat sources or moisture.

3 Do not place objects containing liquids or

candles on top of theTV.

4 Never open the back cover.

5 Never insert objects into the TV.

6 Take care not to damage the power cord.

7 Keep the TV from strongly  magnetic

objects.

8  To prevent fire, never place any type of candle

or naked flames on the top or near the TV set.

PROBLEM

CHECK ITEM

PAGE

- TV not plugged in Outlet power OFF

- Main Power button of TV not ON

- Aerial not connected to terminal at the back of the TV

set

- Check STEREO Menu: Speakers matrix and

Identification.

No picture or sound

-  Aerial not connected to terminal at the back of the TV

set

-  Adjust COLOUR control

-  Check if the Brightness or Contrast setting in the

picture setting mode might be all the way to the minus
side

Sound OK, picture poor

Picture OK, sound poor

- Increase the volume

- Check AUDIO MODE and Audio levels Menus

- Poor equalizer adjustment. Check Graphic Equalizer

- Check STEREO Menu: Speakers matrix and

Identification.

Picture weak / No colour

-  Aerial not connected to terminal at the back of the TV

set

-  Adjust COLOUR control

-  Try fine tuning to correct

Poor reception on some

channels

-  Aerial not connected to terminal at the back of the TV

set

- Check for local interference

Remote control

does not work

- TV not plugged in Outlet power OFF

- Main Power button of TV not ON

- Turn OFF using the Main Power button, then turn ON again

after a minute

- Check batteries in the Remote Control

If problems persist contact the SHARP Helpline (office hours only) on

tel:08705 274277 (or (01) 676 0648 if telephoning from Ireland)

and/or WEB-SITE:www.sharp.co.uk/support

COLOUR TELEVISION

OPERATION MANUAL

Printed on recycled paper

Please read this operation manual carefully
before using the colour television.

1 Press the main power button (

®)

to start the AUTO INSTALLATION.

2 The orange power indicator will light.

3 The AUTO INSTALLATION            

message will appear on your TV        
screen, and after a time will change
for another with electrical connetions

Note:
If you need to repeat the “AUTO
INSTALLATION”, please refer to the
relevant section on page 28 of the
operation manual.

The AUTO INSTALLATION function will tune all available
TV stations into your TV.
The TV is ready to preset automatically all local channels
for you.

1. With your

thumb nail,
pull up the slit
as shown.

2. Insert the two

batteries as
shown.

3. Replace the
    cover.

●

 Is the TV connected to the mains?

● 

Is the aerial connected to the TV?

If you do not intend to use your TV with
a VCR then please proceed to stage 4.2

1 If the TV is being used
  with a VCR, turn on the

VCR and play back a

    pre-recorded tape.

2 Now, press any button
   on the TV remote

control and follow the

  instructions on the

screen, to start Auto
Channel Preset.

This tuning process may
take several minutes to
perform.

3 After searching has
  finished the channels

The "Stored programmes" menu will appear on screen
and you can change the order of the channels and change
or give the channels a four letter name.

If you wish to rename the channels, or change the order,
refer to the pages 8 and 9, chapter Stored programmes
in the Operation Manual

If you wish exit from the menu, press the BLUE button.

Remote control

Type-AA Dry Batteries

Operation Manual

Automatic searching and sorting

Press the menu button to cancel

Mains Socket Outlet

AC 220~240 V, 50 Hz

A scart lead (not supplied) is recommended for use with this TV, to
obtain the best communication between your TV and VCR, please refer
to page-36 of the operation manual.

Note: for Satellite/Cable or digital decoder page 36 of operation manual.

BACK OF TV

Mains Socket Outlet

AC 220~240 V, 50 Hz

Aerial Lead
(Not supplied)

SCART Lead

(Not supplied)

Aerial

(Not supplied)

Aerial Lead

(Not supplied)

Aerial in

Audio/Video

RF out

BACK OF VCR

Mains Socket Outlet

AC 220~240 V, 50 Hz

Aerial Lead

(Not supplied)

Aerial
(Not supplied)

Power indicator

Main power button