DOWNLOAD Sharp 66FW-54H (serv.man12) Service Manual ↓ Size: 2.32 MB | Pages: 52 in PDF or view online for FREE

STATION

REAL CHANNEL

FREQUENCY

SIGNALS

NUMBERS

MHZ

VHF

I-1 (A) ÷ I-9 (J)

CH-01 ÷ CH-09

45.75 ÷ 215.25

UHF

I-21 ÷ I-69

CH-21 ÷ CH-69

471.25 ÷ 855.25

C

M1/S1 ÷ M10/S10

CC-01 ÷ CC-10

105.25 ÷ 168.25

A

U-1/S-11 ÷ U-10/S-20

CC-11 ÷ CC-20

231.25 ÷ 294.25

T

S-21 ÷ S-41

CC-21 ÷ CC-41

303.25 ÷ 463.25

V

CC-42 ÷ CC-63

48 ÷ 304

CC-64 ÷ CC-68

69.25 ÷ 98.25

8

Power indicator

Main power button

This TV memorizes the Mode last used when it was switched off. When the
main power button (

I

) is pressed to turn on the set, the power indicator will

light and the set will resume in either the Stand-by mode or Programme
mode, depending upon its condition when it was switched off.

When the TV is in Stand-by mode, to turn ON the TV press the Stand-by but-
ton (

B

l

TV) on the remote control, or one of the four buttons on the TV

( Va/\, VCH/\ ). The TV will change from Stand-by mode to Programme
mode, the sound indicator will light a few moments and an image will appear
on the screen. Press the Stand-by button (

B

l

TV) again and the TV will

return to Stand-by mode.

If noise appears in TV or VCR mode, the screen turns blue. The blue back off-timer is then engaged and will automatically
switch to Stand-by mode after 15 minutes.

Channel setting is mainly performed using the remote control. Please follow the instructions with the remote control in
hand.
Television broadcasting stations have channel numbers assigned to them (real channel numbers). You can assign your
own channel number to a real channel and store it in the programme preset memory.

9

Auto Installation System
Your television set is provided with an Automatic Installation System which makes Installation easier.
This new system is activated when you turn on the TV for the first time.

Procedure:
1. Put batteries into the remote control and connect the antenna jack into the antenna input terminal on the rear of your

TV, as shown on page 4 and 5.

2. Connect the TV power cable to a 220 ~ 240 V system.

3. Press the main power button (

I

), on the right hand side of the TV

set, to start the “AUTO INSTALLATION”.

4. The red power indicator will light.

5. The “AUTO INSTALLATION” message will appear on your TV

screen.

•

The TV is ready to preset automatically all local channels for you.

•

If the TV is being used with a VCR, turn on the VCR and play back
a pre-recorded tape.

6. Now, press any button on the TV remote control and follow the

instructions on the screen, to start Auto Channel Preset.

Automatic Channel Sorting System (ACSS): The TV set SEARCHES
FOR FREQUENCIES, memorises the channels found, and sorts them
(according to technical criteria) from Pr-01 of the TV, to a maximum of
99 programmes.

Notes: This tuning process may take several minutes to perform.
IF THE TV CANNOT BE INSTALLED BY THIS METHOD, PLEASE
PHONE THE FOLLOWING NUMBER: 

If you need to repeat the “AUTO INSTALLATION”, please read -TV
Channel Setting- (page 32).

Stored programmes: When the AUTOMATIC SEARCH has been
completed, the "Stored programmes" Menu will appear on screen and
you can change the order of the channels and change or give the
channels a four letter name with the available options:

a) Select programme to be edited.
b) Delete this programme.
c) Go to sorting mode.
d) Edit this programme.
e) Exit.

For a more detailed explanation see page 10.
If you wish exit from the menu, press the BLUE button.

: 

It is advisable to use Pr 01, Pr 02, Pr 03 and Pr 04 for the most often used

programmes with teletext and for those which contain their own programme
information and information on other channels in the Teletext pages. For more
explanation, please go on to the section entitled TV-GUIDE.

Power indicator

Main power button

Automatic searching and sorting.
Press the menu button to cancel.

10

Select programme to be edited.
Use this option to select a programme from the list. Each time

you press 

E

or 

F

the memorised channel will be

viewed and will remain selected on the list by means of white
background.

Delete this programme.
Use this option for cancelling programmes which are badly tuned
or repeated.

b.1 Select the programme (Pr) you wish to delete using Cursor

UP/DOWN buttons  

E

/ 

F

(marked with white 

background).

b.2 Press the YELLOW button 

to see the “Delete Menu”.

When the YELLOW button 

is pressed, the TV will ask for

confirmation that you wish to cancel, and you must press the

YELLOW button 

again. The channels that follow it on the

list will automatically rearrange themselves by moving up one
programme (Pr) place, to restore the space of the cancelled
channel (CH).

Go to sorting mode
Use this option for sorting the channels (CH) into the desired
programme (Pr), as follows:

c.1 Select the programme (Pr) you wish to change using Cursor

UP/DOWN buttons  

E

/ 

F

(marked with white

background).

c.2 Press the GREEN button 

to see the “Sorting Menu”.

c.3 Press the Cursor UP/DOWN buttons  

E

/ 

F

to move

the channel (CH) to the required position.

c.4 Press the GREEN button 

to finish.

Edit this programme
Use this option for giving a name made up of four digits to the
channels or for changing the one which appears on some
channels, in the following way:

d.1 Select the channel using the Cursor UP/DOWN buttons  

E

/

F

.

d.2 Press the RED button 

to see the “Edit Menu”.

d.3 Press the Cursor UP/DOWN buttons  

E

/ 

F

to change

the first letter. Letters A to Z of the alphabet, a blank space and
the numbers 0 to 9 will appear sequentially. Some of the
broadcasting stations names such as BBC1 or CH4 are already
incorporated in the TV and appear among the alphabet to make
this task easier.

d.4 Press the

I

button for changing the position of the cursor and

the   

E

/ 

F

buttons for changing the letters (repeat this

action for other letters).

d.5 When you have finished the fourth letter, press the 

I

button to quit the “Edit Menu” option.

Note: Use the names that appear sequentially in section d.3 to ensure the better functioning of the “TV GUIDE”.

Use this option to quit the menu by pressing the BLUE button 

.

11

E/F

Select the programme channel number you want to see, using the
channel selector buttons 

E

or

F

.

When you press these buttons the list of programmes appears. 
Press the  

E

or

F

again to select another program.

Note: The channels that are in SKIP mode cannot be seen with these
buttons. Use numerical buttons to display these channels.

 

6

This button selects between one or two digit channel number entry.

You can select channels by pressing the 0 ~ 9 digit buttons on the remote control.
(For single and double digit entry see section B above).

Press this button to change from the current channel to the channel previously selected. Press the button again to switch
back to the original channel.

Single digit

entry mode

Double digit

entry mode

Previously

viewed channel

Currently

viewed channel