DOWNLOAD Sharp 66FW-54H (serv.man11) Service Manual ↓ Size: 648.44 KB | Pages: 36 in PDF or view online for FREE

20

Loudness increases the volume of low and high frequency signals according to the current volume setting.

In NORMAL mode keeping the amplitude of the 1 KHz reference frequency constant.
In SPECIAL mode keeping the amplitude of the 2 KHz reference frequency constant.

Press the MENU button  

●

to see the MAIN Menu.

Press the GREEN button 

to see the AUDIO EFFECTS

Press the RED button 

to see the SPEAKERS LEVELS

Press the Cursor UP/DOWN buttons 

E

/ 

F

to select:

Volume, Balance, Loudness mode, Volume centre, Volume surround
or Noise sequencer.

The red point mark indicates the selected item.

Adjust the sound quality to your liking with the Cursor LEFT/RIGHT

buttons 

C 

/

I

.

Note: When the AUDIO MODE is on Bypass, Panorama or Spatial
expander mode, the Volume centre, Volume surround and Noise
sequencer options do not appear.

Select Loudness mode (NORMAL, SPECIAL or OFF) to improve the
sound quality [

].

Select Volume centre to adjust the central volume.

Select Volume surround to adjust the rear loudspeakers volume.

Select Noise sequencer: When Noise sequencer is set to on by 

C 

/

I

buttons, a noise test will be heard through the loudspeakers
(LEFT/RIGHT/CENTRE/SURROUND) [

]. In this mode you can easily

adjust the balances:

• Press the Cursor UP/DOWN buttons 

E

/ 

F

to select: Volume,

Balance, Volume centre, Volume surround or, Volume subwoofer.

• Press the Cursor LEFT/RIGHT buttons 

C 

/

I

to adjust.

• Press the Cursor UP/DOWN buttons 

E

/ 

F

to select Noise

sequencer and press the Cursor LEFT/RIGHT buttons 

C 

/

I

to deactivate

the Noise sequencer.

Press the RED button 

to see the HEADPHONES LEVELS

Balancing the sound levels in two channel stereo is simple and direct, but when three or four channels are used,
the task becomes more difficult. To enable the user to accurately set system balance, a steady test signal is played
in one channel at a time and the levels can be adjusted until they match each other. A mid-frequency noise signal is
used so that it will sound similar from all speakers in the system regardless of size or location.

21

Press the Cursor UP/DOWN buttons  

E

/ 

F

to select:

Volume, Balance, Loudness mode, Bass or Treble.
The red point mark indicates the selected item.

Adjust the sound quality to your liking with the Cursor

LEFT/RIGHT buttons  

C 

/

I

.

Press the RED button 

to see the EXTERNAL LEVELS

10. Press the Cursor UP/DOWN buttons  

E

/ 

F

to select:

SCART volume or AV volume.
The red point mark indicates the selected item.
Select SCART volume to adjust the sound level output to the
Euro-SCART connector (RGB) with the Cursor LEFT/RIGHT

buttons  

C 

/

I

.

Select AV volume to adjust the sound level output to the
external connectors (AV-1/AV-2) with the Cursor LEFT/RIGHT

buttons  

C 

/

I

.

11. Press the MENU button 

●

to close the AUDIO LEVELS

Press the MENU button  

●

to see the MAIN Menu.

Press the GREEN button 

to see the AUDIO EFFECTS

Press the GREEN button 

if you wish to normalize audio

levels to default factory setting.

GREEN

22

Press the MENU button  

●

to see the MAIN Menu.

Press the GREEN button 

to see the AUDIO EFFECTS

Press the YELLOW button 

to see the EQUALIZER Menu.

Press the YELLOW button 

to select a pre-defined

equalization: Personal / Classic / Jazz / Pop / In concert / Sport .

To change the Personal option:

a) Press the Cursor LEFT/RIGHT buttons  

C 

/

I

to select:

100Hz, 330Hz, 1KHz, 3.3KHz or 10KHz 
The red point mark indicates the selected item.

b) Press the Cursor UP/DOWN buttons  

E

/ 

F

to

Adjust.

Note: The Equalizer adjustments are not operative for the    

headphones.

Press the BLUE button 

to see the STEREO Menu.

Press the Cursor UP/DOWN buttons  

E

/ 

F

to select:

Speakers matrix, Headphones matrix, AV Matrix [

] or

Identification.
The red point mark indicates the selected item.

Press the Cursor LEFT/RIGHT buttons  

C 

/

I

to change.

Select Speakers matrix to change the sound mode in the
speakers.
Select Headphones matrix to change the sound mode in the
headphones.
Select AV matrix to change the sound mode in the audio output
of the external connector (AV-1/AV-2).
Select Identification to activate (ON) or deactivate (OFF) the
automatic Identification of audio system of the current program
[

] .

Press the MENU button 

●

to close the STEREO Menu.

About Matrix: Depending on the sound transmission the sound reproduction can be chosen in the STEREO Menu.

In this menu you can select a sound mode to the speakers, another to the headphones and another to the external connectors (AV-1/AV-2).
When the TV set is receiving a STEREO NICAM programme, the TV selects STEREO automatically, and you can change:

STEREO 

MONO

When the TV is receiving a BILINGUAL NICAM programme, the TV selects DUAL CHANNEL A automatically, and you can change:

DUAL CHANNEL A 

DUAL CHANNEL B 

DUAL CHANNEL A B 

MONO

When the TV set is receiving a MONO NICAM programme, the TV set selects MONO NICAM automatically, and you can change:

MONO NICAM 

MONO

When the TV is receiving a MONO FM programme, the TV set selects MONO automatically but the sound mode cannot be change.

 

IDENTIFICATION ON: The TV automatically identifies the received audio system MONO FM, STEREO NICAM or DUAL NICAM SIGNAL.
IDENTIFICATION OFF: Disqualifies the automatic identification of the audio system and forces the sound into MONO FM.
This mode can be convenient when the level of the signal received is extremely weak. This function is independent for every program.

23

In this mode you can set the ON-TIMER and OFF-TIMER, set the CHILD LOCK, activate or deactivate the interactive
HELP, view the all functions implemented in your TV set demonstration and set the Post code.

Press the MENU button 

●

to see the MAIN Menu.

Press the YELLOW button 

to see the Timer Menu.

The On-Timer is used to programme switching ON the TV set during
the 24 hours of the day.
In order to be able to run this function, it is essential to adjust the
current time

Press the Cursor UP/DOWN buttons 

E

/

F

to select

“Current time”. The red point mark indicates the selected item.

Automatic TIME adjustment: If a programme with teletext is being
received, the “Current time” can be adjusted automatically with that
signal's clock.
To synchronize “Current time”, press Text/Mix button 

a

/

b

.

*

Important: If a signal via satellite is being received, or if correct time

cannot be obtained, the time will have to be adjusted manually.

Manual time adjustment: Press the Cursor LEFT/RIGHT buttons  

C 

/

I

to adjust the “Current time” manually.

Press the Cursor UP/DOWN buttons  

E

/

F

to select “Programmed switch on at”. The red point mark

indicates the selected item.

Press the Cursor LEFT/RIGHT buttons 

C 

/

I

to adjust the switch on.

To cancel the switch on, select 

.

Press the MENU button 

●

to close the ON TIMER Menu.

Press the Stand-by button ( 

æ 

TV) on the remote control to put the TV set into Stand-by Mode.

When the preset time is reached, the TV set turns ON and a picture appears on the screen.

* As a safety precaution, in the case of nobody being home when the television switches on automatically, the television
will disconnect itself after 120 minutes; if it is to continue to run, any button on the remote control functions should be
pressed.

Note: In the event of a power cut, disconnection from the plug or television switch, all the data on the ON TIMER will be
cancelled.

The OFF-Timer is used to programme switching the TV set to Stand-by
mode, after the set length of time has passed.
If necessary, repeat steps (1. ~ 2.) to see the Timer Menu.

Press the Cursor UP/DOWN buttons  

E

/

F

to select   “Off

timer status”. The red point mark indicates the selected item.

Press the Cursor LEFT/RIGHT buttons  

C 

/

I

to select the desired

period (05 ( 180 minutes).
To cancel the OFF-Timer, select 

.

Press the MENU button 

●

to close the OFF -TIMER Menu.

Note: The off timer data will be cancelled if you turn off the TV by the
Stand-by button ( 

æ 

TV) on the remote control or with the Main power

button (

®

) on the TV set.