DOWNLOAD Sharp 37GT-27H (serv.man16) Service Manual ↓ Size: 2.41 MB | Pages: 44 in PDF or view online for FREE

Model
37GT-27H (serv.man16)
Pages
44
Size
2.41 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / CTR
File
37gt-27h-sm16.pdf
Date

Sharp 37GT-27H (serv.man16) Service Manual ▷ View online

1
37GT-27H
   
  MODEL
 
 37GT-27H
SHARP  CORPORATION
CONTENTS
         
  PAL I  SYSTEM COLOUR TELEVISION
  SE0037GT27H00
SQUAD-T 
 CHASSIS
SERVICE MANUAL
In the interests of user safety (required by safety
regulations in some countries) the set should restored
to its original condition and only parts identical to
those specified should be used.
  Issued: 23th  April  2002
ELECTRICAL SPECIFICATION.......................3
IMPORTANT SERVICING NOTES.......................4
SERVICE ADJUSTMENTS...............................5
PRINTED WIRING BOARDS..........................12
COMPONENT LOCATION TABLES................14
ICs ADDITIONAL INFORMATION..................17
○○
SCHEMATIC DIAGRAM, WAVE FORMS.......24
BLOCK DIAGRAM..........................................30
TROUBLESHOOTING TABLES......................32
PARTS  LISTING..................................................37
PACKING OF THE SET...................................42
REMOTE CONTROL DESCRIPTION..............43
FASTEXT
2
37GT-27H
Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc.
If only part  number changes are required, just change part number directly the part number in the Parts Listing Section.
If you need more information, please refer to the Technical Report (Bulletin).
SERVICE MANUAL UPDATE LOG SHEET
Part No.
Technical Report  No.
Technical Bulletin No.
Cause / Solution
Page No.
Application
Data /Serial No.
3
37GT-27H
ELECTRICAL SPECIFICATIONS
Focus ....................... High Bi-Potential Electrostatic
Picture Intermediate frequency...................38.9MHz
Sound  Carrier Trap................................... 32.9MHz
Adjacent  Sound Carrier Trap ................... 40.9MHz
Adjacent  Picture  Carrier Trap.................. 30.9MHz
Aerial Input Impedance
VHF/UHF ...................... 75 ohm Unbalanced
Tuning Ranges........... 45.75 MHz thru 855.25 MHz
VHF: IR A - J / S1 - S41 CH (Hiperband)
UHF: I21 - I69 CH
CATV Special Channels
White Level
Set brightness control to get total picture tube cathode current of 600 
µ
A under no signal condition.
Maximum necessary correction of each picture tube cathode current to get 8950 degrees
 
K-20 MPCD
screen temperature should not exceed 15% of its original value.
X=0.290 ± 0.015         Y=0.284 ± 0.015
                                            WARNING
The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug
and power receptacle, when servicing this chassis.
To prevent electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to
qualified service personnel.
Specifications are subject to change without prior notice.
Power Input .................... 220V-240 Volts AC 50Hz
Power Consumption
Normal Operation (Method IEC60107) ............ 30W
Stand-by Operation ..........................................7.5W
Audio Power Output Rating (MPO) / Impedance
Speaker...................................................... 2W, 32
Speaker.............................................................8cm Round
Convergence (Maximum Misconvergence)
Static (Centre) between any two  colours  ... 0.08 cm
Dynamic after static equals zero
Within 10cm (4”) circle ....................... 0.12cm
10-25cm (4-10” ) circle ...................... 0.20 cm
Everywhere else ................................ 0.28 cm
4
37GT-27H
IMPORTANT SERVICING NOTES
Only qualified service personnel are allowed to carry out maintenance and repair of this receiver.
Servicing of High Voltage System and CRT
It is important that the static charge is removed from the high voltage system when carrying out work on the
receiver. This can be achieved by connecting a 10K resistor (with a suitably insulated lead) from the CRT
cavity connector to the CRT ground tag. This must be carried out with the AC supply disconnected from the
receiver.
Note the following:
 
The CRT in this receiver employs Integral Implosion Protection.
 If the CRT has to  be changed  it  MUST  be  replaced  with  the  correct  type for continued safe  working.
 DO NOT lift the CRT by its neck.
 When handing the CRT, ensure that shatterproof goggles are worn.
 Ensure that the CRT is discharge before handling.
X-Ray
This receiver is designed to keep any x-ray emission to an absolute minimum. Some fault conditions  and
servicing procedures may produce potentially hazardous x-ray radiation levels. This is a problem when in
close proximity to the receiver for long  periods of time. To reduce any risks associated with this, please
observe the following precautions:
1. When undertaking any servicing on this chassis, DO NOT increase the EHT  to more than 30KV, (at a
instantaneous beam current of 300
µ
A
)
.
2. Ensure that during normal operation the EHT does not exceed 27.5KV (at a beam current of 800
µ
A). This
level has been preset in the factory. Always check that this level has not been exceeded after carrying out
any repair on the receiver.
3. DO NOT replace the CRT with any other type than that specified in the parts listing as this may cause
excessive x-ray radiation.
Before returning the receiver to the customer
In addition to the above checks, the following should also be carried out before  returning the receiver  to the
customer.
1. Inspect all the leads to ensure that they are dressed correctly and that they are not obstructed or pinched
by any other parts.
2. Ensure that all protective devices are in good condition. These will include nonmetallic control knobs,
insulating fish papers, cabinets backs, compartment covers or shields, mechanical insulators, etc.
Page of 44
Display

Sharp 37GT-27H (serv.man16) Service Manual ▷ Download

  • DOWNLOAD Sharp 37GT-27H (serv.man16) Service Manual ↓ Size: 2.41 MB | Pages: 44 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp 37GT-27H (serv.man16) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp 37GT-27H (serv.man16) CTR. Information contained in Sharp 37GT-27H (serv.man16) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.